# What is API 574 (inspection practices for piping)?

> API 574 is the American Petroleum Institute's recommended practice (RP) for inspecting piping, valves and fittings in refineries and chemical plants. It also covers tubing, leaves out control valves, and supplements the API 570 code for in-service piping. The current 5th edition was published in February 2024, with Addendum 1 in March 2025.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T11:53:52+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: Refining
- Canonical: https://beacon.winda.ai/library/api-574/

## Why does it matter?

In June 2019 a steel elbow in the hydrofluoric acid (HF) alkylation unit of a Philadelphia refinery ruptured, starting fires and explosions; the refinery estimated that 5,239 pounds of HF were released, and an insurance industry report cited by investigators put the property loss at about $750 million [1]. The elbow's piping circuit had grown from 41 condition monitoring locations (CMLs) in 2002 to 141 by 2019, but none of them was on the elbow that failed [1]. The elbow held high levels of nickel and copper and had thinned much faster than neighboring components, which were not thin [1]. Industry practice at the time did not require every carbon steel component in HF service to be inspected; according to the CSB, API RP 751 on HF alkylation was revised after the incident so that each carbon steel component in known corrosion zones is now inspected [1].

## What does API 574 cover?

API RP 574, *Inspection Practices for Piping System Components*, is a recommended practice that API's catalog pairs with the API 570 piping code, as a reference that builds inspectors' working knowledge [2]. It deals with the parts that make up refinery and chemical plant piping systems: the pipe and tubing themselves, their fittings, and valves, with control valves left out [2]. API announced the 5th edition [3], dated February 2024 [2], and its effectivity sheet for 2027 inspector exams lists that edition with Addendum 1 of March 2025 [4].

## Where does piping deteriorate, and how is it found?

Refineries divide piping into circuits that share process conditions, material and expected damage, and place condition monitoring locations within each circuit where wall thickness is measured over time [1]. In the CSB's description, a circuit expected to corrode evenly gets fewer CMLs and one prone to local attack gets more [1].

| Location or feature | Why it needs attention | Public source |
|---|---|---|
| Injection points, mixing points and dead legs | The US Occupational Safety and Health Administration (OSHA) points to these spots, where deterioration is likely, as places that need CMLs in addition to readings spread along the line [7] | OSHA 3918, 2017 [7] |
| Dead legs (stagnant branches, relief lines, bypasses) | Corrosion can be aggressive and very local; for high-risk dead legs HSE does not consider spot ultrasonic readings adequate and expects a significant share of the line to be tested [5] | HSE safety alert, 2019 [5] |
| Insulated piping | OSHA cited a refinery for not inspecting for corrosion under insulation on piping and vessels in a sulfur unit [7] | OSHA 3918, 2017 [7] |
| Components with different chemistry | High nickel and copper steel corrodes faster in HF service [1]; low-silicon carbon steel corrodes faster in hot sulfur service [6] | CSB, 2022 and 2015 [1][6] |

## How does API 574 relate to API 570 and to regulators?

API 570 (5th edition, February 2024) is the code that governs metal piping in service, from its inspection program to its repairs [2][4]. RP 574 is a supporting practice, not a code [2]. In the US, the process safety rule requires piping inspection to meet recognized and generally accepted good engineering practice (RAGAGEP) [8], and OSHA names API publications as examples [7]. In the UK, HSE regards API 570, RP 574 and Energy Institute guidance as relevant good practice for reducing pipework risk on major hazard sites [5].

After the 2012 Richmond, California, refinery fire, the CSB recommended that API revise RP 574, then in its 3rd edition, to adopt the sulfidation guideline RP 939-C as a normative reference and to follow a leak response protocol [6].

## Where integrity problems show up

| What it finds well | What it can miss or get wrong | In the Library |
|---|---|---|
| **Thickness readings at CMLs** track general wall loss across a circuit [1] | One component corroding faster than its circuit: the Philadelphia elbow had no CML [1] | [What are condition monitoring locations (CMLs)?](/library/condition-monitoring-locations/) · [Corrosion circuit](/glossary/corrosion-circuit/) |
| **Spot ultrasonic checks** at fixed points [5] | Local thinning between points: the 8-inch UK relief line that ruptured in 2019 was tested at four locations, none near the failure, and released about 75 tonnes of flammable material [5] | [Dead leg](/glossary/dead-leg/) · [How does ultrasonic thickness measurement work?](/library/ultrasonic-thickness-measurement/) |
| **Remaining-life forecasts** from thickness data [6] | Readings taken historically on high-silicon fittings at Richmond suggested the line could run until 2016; a low-silicon component failed in August 2012 [6] | [What is sulfidation (high-temperature sulfur corrosion)?](/library/sulfidation/) · [Remaining life](/glossary/remaining-life/) |
| **Inspection of exposed piping** surfaces | Corrosion under insulation when insulated lines are not included [7] | [What is corrosion under insulation (CUI)?](/library/corrosion-under-insulation/) |

Sources: CSB reports on Philadelphia (2022) [1] and Richmond (2015) [6]; HSE safety alert CEMHD2-2019 [5]; OSHA 3918 [7].

## Sources

1. [Investigation Report: Fire and Explosions at Philadelphia Energy Solutions Refinery Hydrofluoric Acid Alkylation Unit, Report No. 2019-04-I-PA, US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/20/PES_Final_Report_Published_October_2022_r1.pdf?16845), 2022-10-11
2. [2025 Publications Catalog (entries for API 570 and RP 574) (RP 574, 5th edition, February 2024; API 570, 5th edition, February 2024), American Petroleum Institute (API)](https://www.api.org/-/media/files/publications/2025-catalog/2025_pubs%20catalog.pdf)
3. [API Recommended Practice 574, 5th edition (standards announcement), American Petroleum Institute (API)](https://www.api.org/products-and-services/standards/important-standards-announcements/rp574)
4. [API 570 Exam Publications Effectivity Sheet for February 2027 and June 2027 (RP 574, 5th edition, February 2024, Addendum 1 (March 2025)), American Petroleum Institute (API)](https://www.api.org/-/media/Files/Certification/ICP/ICP-Certification-Programs/570/2027/570_Publications%20EffectivitySheet_Final_Feb_June%202027.pdf)
5. [Catastrophic rupture of dead-leg pipe-work (Safety alert, Bulletin No. CEMHD2-2019), UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/safetybulletins/catastrophic-rupture-dead-leg-pipe-work.htm), 2019-08-20
6. [Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire, Report No. 2012-03-I-CA, US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/17/Chevron_Final_Investigation_Report_2015-01-28.pdf?15397), 2015-01-28
7. [Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918), US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/Publications/OSHA3918.pdf)
8. [29 CFR 1910.119, Process safety management of highly hazardous chemicals, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)

Published by Winda Beacon (https://beacon.winda.ai).
