# What is ASME B31.8S?

> ASME B31.8S is the ASME standard for building an integrity management program for onshore gas pipeline systems made of ferrous materials. Its title is Managing System Integrity of Gas Pipelines. US federal rules for gas transmission integrity management (49 CFR 192, Subpart O) incorporate its 2018 edition; ASME's latest edition is 2025.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T11:53:52+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: LNG, Pipelines
- Canonical: https://beacon.winda.ai/library/asme-b31-8s/

## Why does it matter?

The edition of ASME B31.8S that US federal rules enforce is not the newest one. The federal list of incorporated documents, 49 CFR 192.7, names the 2018 edition (issued November 28, 2018) and ties it to 15 sections of Part 192, while ASME's product page lists a 2025 edition [1][2]. Subpart O tells operators to follow B31.8S and its appendices where the rule says so, and states that the rule wins wherever the two conflict [3]. For US compliance, the text that applies is therefore the 2018 edition read together with Subpart O [2][3].

## What does ASME B31.8S cover?

ASME B31.8S, *Managing System Integrity of Gas Pipelines*, belongs to ASME's B31 family of piping standards [1]. ASME's product page describes it as a basis for building and running an integrity management program, for onshore gas systems made of ferrous material, taking in the line pipe and also the stations, storage and other equipment connected to it [1]. The page lists eight editions, from 2010 to the current 2025 edition [1].

## How do US rules use B31.8S?

The US Pipeline and Hazardous Materials Safety Administration (PHMSA) issued the gas transmission integrity management rule at 68 FR 69778, effective February 14, 2004, and operators had until December 17, 2004, to put written programs in place [4][5][3]. The rule points to B31.8S for specific tasks:

| Subpart O section | What the rule takes from B31.8S |
|---|---|
| 192.903, high consequence area (HCA) definition | Potential impact radius for gases other than natural gas (B31.8S section 3.2) |
| 192.907(b) | Follow B31.8S and its appendices where specified; Subpart O controls in a conflict |
| 192.911(i) and (l) | Performance plan (section 9) and quality assurance process (section 12) |
| 192.913(a) | Features of prescriptive and performance-based programs |
| 192.917(a) to (c) | Threats listed in section 2; data gathering and integration (section 4); risk assessment (section 5) |
| 192.921(a)(2) and 192.939 | Test pressures and reassessment intervals (Table 5.6.1-1 of section 5) |
| 192.923(b)(1) | External corrosion direct assessment (section 6.4, with NACE SP0502) |
| 192.945(a) | Four overall performance measures (section 9.4) and threat-specific measures (Appendix A), reported yearly |

Source: 49 CFR 192.7 and Subpart O, eCFR, up to date as of 22 Oct 2026 [2][3].

Subpart O itself lists the threats an operator must consider, in four groups: time-dependent threats such as internal and external corrosion and stress corrosion cracking; stable threats such as manufacturing, welding and construction defects; time-independent threats like damage by third parties, incorrect operation, and weather or outside force; and human error [3].

**Worked example of the federal impact radius formula** (illustrative numbers, not from any real asset or standard table). 49 CFR 192.903 sets the potential impact radius for natural gas as r = 0.69 × √(p × d²), with r in feet, p the maximum allowable operating pressure (MAOP) in psi and d the nominal diameter in inches [3]. For p = 1,000 psi and d = 30 inches, r = 0.69 × √900,000 ≈ 655 feet (about 200 m). Buildings and identified sites inside that circle decide whether the segment lies in an HCA [3].

## What are prescriptive and performance-based programs?

Subpart O states that B31.8S gives the essential features of both [3]. PHMSA describes the rule as largely prescriptive, with fixed deadlines, reassessment intervals and remediation times [5]. An operator that shows exceptional performance, including a full risk analysis, a data integration process, semi-annual performance measures and at least two assessments of each covered segment, may deviate only on reassessment timing, with some reassessment still within 7 years, and on remediation timing [3].

## Where integrity problems show up

| Decision | Data it depends on | What goes wrong without it | In the Library |
|---|---|---|---|
| Which segments the program covers | MAOP and diameter for the impact radius; buildings and identified sites inside it [3] | A Class 2 segment near Sissonville, West Virginia, lay outside any HCA, was not in the operator's program and had not been inspected or tested after 1988; it ruptured in 2012 with more than 70% wall loss [6] | [High consequence area](/glossary/high-consequence-area/) |
| Which threats apply to a segment | Integrated pipe, coating, cathodic protection, test, assessment and monitoring data, including gas stream sampling [3] | Before the 2000 Carlsbad, New Mexico, rupture, the National Transportation Safety Board (NTSB) found, gas quality monitoring and sampling of removed liquids would likely have shown the corrosion potential [7] | [What is corrosion monitoring and which methods are used?](/library/corrosion-monitoring/) |
| How to assess each threat | Threats per segment; methods from in-line inspection to direct assessment [3] | Direct assessment may not be used for threats other than external and internal corrosion and stress corrosion cracking [3] | [What is direct assessment (ECDA, ICDA, SCCDA)?](/library/direct-assessment/) |
| Whether findings apply to similar pipe | Corrosion and crack findings, material, coating and environment [3] | At Sissonville, 2009 in-line inspection data showing external corrosion on two adjacent HCA lines was not adequately considered for the line that failed [6] | [What is pipeline integrity management?](/library/pipeline-integrity-management/) |

Sources: 49 CFR 192 Subpart O [3]; NTSB/PAR-14/01, 2014 [6]; NTSB/PAR-03/01, 2003 [7].

## Sources

1. [B31.8S, Managing System Integrity of Gas Pipelines (product page) (2025 (editions listed: 2025, 2022, 2020, 2018, 2016, 2014, 2012, 2010)), American Society of Mechanical Engineers (ASME)](https://www.asme.org/codes-standards/find-codes-standards/b31-8s-managing-system-integrity-gas-pipelines)
2. [49 CFR 192.7, What documents are incorporated by reference partly or wholly in this part? (incorporates ASME B31.8S-2018, issued November 28, 2018), eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/section-192.7)
3. [49 CFR Part 192, Subpart O, Gas Transmission Pipeline Integrity Management, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/part-192/subpart-O)
4. [Gas Transmission Integrity Management (GT IM) Overview, US Pipeline and Hazardous Materials Safety Administration (PHMSA)](https://www.phmsa.dot.gov/pipeline/gas-transmission-integrity-management/gas-transmission-integrity-management-gt-im-overview)
5. [GT IM Fact Sheet, US Pipeline and Hazardous Materials Safety Administration (PHMSA)](https://www.phmsa.dot.gov/pipeline/gas-transmission-integrity-management/gt-im-fact-sheet)
6. [Pipeline Accident Report: Columbia Gas Transmission Corporation Pipeline Rupture, Sissonville, West Virginia, December 11, 2012 (NTSB/PAR-14/01), US National Transportation Safety Board (NTSB)](https://www.ntsb.gov/investigations/AccidentReports/Reports/PAR1401.pdf)
7. [Pipeline Accident Report: Natural Gas Pipeline Rupture and Fire Near Carlsbad, New Mexico, August 19, 2000 (NTSB/PAR-03/01), US National Transportation Safety Board (NTSB)](https://www.ntsb.gov/investigations/AccidentReports/Reports/PAR0301.pdf)

Published by Winda Beacon (https://beacon.winda.ai).
