# What does a gas processing plant do?

> A gas processing plant cleans raw natural gas from wells to pipeline quality and recovers natural gas liquids such as ethane, propane and butanes. It removes free liquids, water, hydrogen sulfide, carbon dioxide and other impurities in stages: inlet separation, acid gas removal, dehydration, liquids recovery and fractionation. The order and scope vary by plant.

- Label: Fact
- Type: Explainer
- Published: 2026-11-13T09:39:01+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-13
- Topics: LNG, Pipelines
- Canonical: https://beacon.winda.ai/library/gas-processing-plant/

## What is removed from raw natural gas, and why?

Gas at the wellhead is mostly methane, but it also carries heavier hydrocarbons, water, hydrogen sulfide (H2S), carbon dioxide (CO2), nitrogen and sometimes helium, oil and condensate [2][1][11]. Long-distance transmission pipelines accept only gas that meets a quality specification [1]. In its 2006 review, the US Energy Information Administration (EIA) described pipeline-quality gas as having a heat content of about 1,035 British thermal units (Btu) per cubic foot, plus or minus 50, with only traces of H2S, CO2, nitrogen, water vapor and oxygen and no free water or solids [1].

Each impurity causes a different problem. Water can form hydrates, ice-like solids that block valves and gathering lines [4]. Gas outside the specification can cause operating problems and pipeline deterioration [1]. The US Environmental Protection Agency (EPA) calls gas "sour" when H2S exceeds 0.25 grains per 100 standard cubic feet, about 5.7 mg per normal cubic meter [5].

The heavier hydrocarbons are not waste. Once separated, natural gas liquids (NGLs) are sold as feedstock for refineries and petrochemical plants, as fuels and for enhanced oil recovery [4].

## What are the main steps in a gas processing plant?

The table follows the order most often described, but EIA notes that the steps can run in a different order or at the same time, and some happen away from the plant, for example at a lease separator [2].

| Step | What happens | Main equipment | What leaves the step |
|---|---|---|---|
| 1. Inlet separation | Free water and liquid hydrocarbons drop out of the incoming gas, which EIA (2006) says typically arrives at 600 psig (about 41 bar gauge) or more | Inlet slug catcher, separators | Condensate to stabilization and storage; produced water |
| 2. Acid gas removal | An amine solution absorbs H2S and CO2 | Amine absorber, regenerator | Acid gas to sulfur recovery, incineration or flare; CO2 vented or sent for enhanced oil recovery |
| 3. Dehydration | Water is absorbed by a liquid glycol or adsorbed on solid desiccant beds such as silica gel or activated alumina | Glycol contactor and regenerator, or desiccant towers | Dry gas; removed water |
| 4. NGL recovery | Gas is chilled so that ethane and heavier components condense, or a lean oil absorbs them | Turboexpander, cold heat exchangers, absorber | Methane-rich gas to the pipeline; mixed NGL stream |
| 5. Fractionation | The mixed NGL stream is separated in stages by boiling point | Distillation towers with reboilers | Ethane, propane, butanes and natural gasoline |

Sources: EIA (2006) [1]; EPA AP-42 (1995) [5]; Occupational Safety and Health Administration (OSHA) Technical Manual [6]; PHMSA (2017) [4].

Some plants add a nitrogen rejection unit, and some recover helium by membranes or pressure swing adsorption [1]. Where H2S goes to a sulfur recovery unit, the Claus process turns it into elemental sulfur through thermal and catalytic reactions [6].

## How are natural gas liquids recovered and separated?

EIA's 2006 review describes two main recovery methods [1]. In cryogenic processing, a turboexpander and external refrigeration chill the gas to about -120 °F (about -84 °C), so heavier components condense while methane stays a gas [1]. This route recovers light liquids such as ethane better than absorption does [1].

In absorption, a lean oil soaks up the NGLs in a tower; the rich oil is then heated to release them and is reused. A refrigerated version chills the lean oil to improve recovery somewhat [1]. The recovered mixture then goes to fractionation, where it is split in a series of towers into ethane, propane, butane, isobutane and natural gasoline [4][1].

## Where does a gas plant sit between the well and the pipeline?

Gas reaches the plant through small-diameter, low-pressure gathering lines; a single gathering system can link as many as 100 wells to one plant [4]. Some cleanup happens before the plant, at lease separators, heaters and scrubbers near the wells [1]. After processing, the dry gas enters transmission pipelines, which carry it to consumers, often over hundreds of miles [4].

EIA counted 530 gas processing plants in the Lower 48 US states in 2004, with about 60.5 billion cubic feet per day of capacity [1]. Capacity rose from 77.5 to 90.8 billion cubic feet per day between 2009 and 2010 [3].

## Where integrity problems show up

| Unit or equipment | Typical integrity issue | In the Library |
|---|---|---|
| Gathering lines and inlet piping carrying wet raw gas | Internal corrosion where water is present with CO2 and H2S from the gas | What is carbon dioxide (CO2) corrosion? |
| Amine absorber, regenerator, reboiler and amine piping | Amine-related corrosion and cracking; OSHA notes that corrosion control depends on regenerator bottom and reboiler temperatures | What is amine corrosion and amine cracking? |
| Carbon steel vessels in wet sour service, such as amine absorbers | Hydrogen-induced cracking from wet H2S; a 1986 OSHA memo reports this finding for a failed absorber's plate steel | What is wet hydrogen sulfide (H2S) damage? |
| Cold heat exchangers in the liquids recovery section | Brittle fracture: at Longford, Australia (1998), an exchanger chilled to about -42 °C after loss of warm oil flow ruptured when warm oil was reintroduced; 2 people died | What is brittle fracture? |
| Insulated piping in cold or cycling service | Corrosion under insulation, most often between -12 and 177 °C (10 and 350 °F) and in service that cycles through that range | [What is corrosion under insulation (CUI)?](/library/corrosion-under-insulation/) |

Sources: PHMSA, Fact Sheet: Internal Corrosion (2018) [8]; OSHA memorandum of 11 April 1986 [7] and OSHA Technical Manual Section IV Chapter 2 [6]; Institution of Chemical Engineers (IChemE) Lessons Learned Database summary (2023) [9]; American Institute of Chemical Engineers (AIChE) Center for Chemical Process Safety (CCPS), Process Safety Beacon (June 2019) [10].

## Sources

1. [Natural Gas Processing: The Crucial Link Between Natural Gas Production and Its Transportation to Market, U.S. Energy Information Administration, Office of Oil and Gas](https://www.dnr.louisiana.gov/assets/docs/oilgas/productiondata/ngprocess_20060131.pdf)
2. [Natural gas explained: Delivery and storage of natural gas, U.S. Energy Information Administration](https://www.eia.gov/energyexplained/natural-gas/delivery-and-storage.php)
3. [U.S. natural gas processing capacity expands rapidly (Today in Energy), U.S. Energy Information Administration](https://www.eia.gov/todayinEnergy/detail.php?id=3090), 2011-09-15
4. [Fact Sheet: Natural Gas Processing Plants, Pipeline and Hazardous Materials Safety Administration (PHMSA)](https://primis.phmsa.dot.gov/stakeholder-comms/factsheets/fsnaturalgasprocessingplants)
5. [AP-42, Compilation of Air Emission Factors, Section 5.3: Natural Gas Processing, U.S. Environmental Protection Agency](https://19january2021snapshot.epa.gov/sites/static/files/2020-09/documents/5.3_natural_gas_processing.pdf)
6. [OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Process, Occupational Safety and Health Administration](https://www.osha.gov/otm/section-4-safety-hazards/chapter-2)
7. [Potentially Hazardous Amine Absorber Pressure Vessels Used in Refinery Processing (memorandum), Occupational Safety and Health Administration](https://www.osha.gov/laws-regs/standardinterpretations/1986-04-11), 1986-04-11
8. [Fact Sheet: Internal Corrosion, Pipeline and Hazardous Materials Safety Administration (PHMSA)](https://primis.phmsa.dot.gov/stakeholder-comms/factsheets/fsinternalcorrosion)
9. [Deethaniser Reboiler Catastrophic Failure (Lessons Learned Database, individual incident summary), Institution of Chemical Engineers (IChemE); author P. Marsh](https://www.icheme.org/media/14214/longford-incident-summary-25-sep-98.pdf), 2023-07-03
10. [Process Safety Beacon: Corrosion Under Insulation, AIChE Center for Chemical Process Safety](https://www.aiche.org/resources/publications/cep/2019/june/process-safety-beacon-corrosion-under-insulation)
11. [40 CFR 98.238, Definitions (Subpart W, Petroleum and Natural Gas Systems), Electronic Code of Federal Regulations (eCFR)](https://www.ecfr.gov/current/title-40/chapter-I/subchapter-C/part-98/subpart-W/section-98.238)

Published by Winda Beacon (https://beacon.winda.ai).
