# HAZOP vs HAZID: what is the difference?

> A hazard identification study (HAZID) screens early for major hazards; a hazard and operability study (HAZOP) examines process deviations in detail later. A HAZOP applies guide words to each section of the piping and instrument diagrams (P&IDs), while a HAZID uses broader prompts such as fire or dropped objects. IEC 61882 is the HAZOP application guide.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T11:57:56+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: LNG, Refining, Upstream and offshore
- Canonical: https://beacon.winda.ai/library/hazop-vs-hazid/

## Why does it matter?

A project with process flow diagrams but no P&IDs yet cannot run a full HAZOP. UK Health and Safety Executive (HSE) guidance places the full study on frozen P&IDs, after earlier stages that identify major hazards and run a coarse HAZOP on the flowsheet [1]. Australia's offshore regulator, NOPSEMA, likewise suggests a coarse HAZOP or a HAZID at concept stage [2]. Order matters because, as HSE notes in its guidance on control systems, hazards found after design has begun are hard to design out, and harder and more expensive to deal with later in a system's life [3].

## HAZOP vs HAZID at a glance

| | HAZID | HAZOP |
|---|---|---|
| Question it asks | What hazards could this facility or activity present, and could any cause a major accident? [2] | How could each part of the process depart from its design intent, and what would follow? [5] |
| Typical timing | Concept stage, then repeated after changes, incidents and at set intervals [2] | Detailed design on frozen P&IDs [1]; for US covered processes, revalidated at least every 5 years [4] |
| Main inputs | Facility diagrams, process information, existing conditions, procedures and hazardous material data [2] | P&IDs and the rest of the process safety information, including relief design basis and operating limits [4][5] |
| Prompts | General hazard categories, such as overpressure, corrosion, leak, fire, explosion, gas release and external events [2] | Guide words paired with parameters, such as more pressure or reverse flow [5] |
| Unit of study | An area, process or activity, taken in turn [2] | A study node on the P&IDs, or a step in a procedure [5][6] |
| Output | Hazards and possible major accident events, passed to risk assessment and the safety case [2][7] | Deviations with causes, consequences, safeguards and actions [5] |
| Known limits | Less detailed than a HAZOP [2] | Gives no likelihood [1]; may miss interactions between nodes, mechanical integrity failures and external events [2] |
| Rules and guides | Method left to the operator by NOPSEMA [2]; UK offshore rules require all major accident hazards to be identified [7] | IEC 61882:2016 application guide [6]; a listed method for process hazard analysis under 29 CFR 1910.119(e) [4] |

Sources: HSE [1]; NOPSEMA guidance note GN0107, 2012 [2]; 29 CFR 1910.119 [4]; University of Auckland [5]; IEC [6]; HSE L154, 2015 [7].

## When is a HAZID used?

- **At concept stage,** before detailed drawings exist; NOPSEMA lists a HAZID or coarse HAZOP as suitable then [2].
- **To build the list of major accident hazards** for a safety case. UK offshore safety cases must show that all hazards able to cause a major accident have been identified [7].
- **For hazards outside the process,** such as dropped objects and vessel collisions, which NOPSEMA says HAZOP handles poorly [2].
- **Again over the life of the facility,** after modifications, a major accident event or dangerous occurrence, when a control deficiency is found, and at set intervals [2].

## When is a HAZOP used?

- **On frozen P&IDs during detailed design,** as HSE's third stage [1].
- **As the process hazard analysis** for a process covered by the US Occupational Safety and Health Administration (OSHA) rule, where HAZOP is one of the listed methods [4].
- **For plant modifications,** with written rules deciding how much HAZOP each change gets [1].
- **For operating procedures,** using procedural HAZOP, which IEC 61882:2016 illustrates with a case study [6].
- **On existing plants,** for example when control and instrumentation systems are upgraded [5].

## How do the two studies fit together?

HSE describes a sequence of six studies that runs from the earliest design to early operation [1]. The first identifies major hazards and checks that key hazard data exist. The second is a coarse HAZOP on the flowsheet and block diagram, and the third the full HAZOP on frozen P&IDs. The last three check that actions were done, carry out a pre-commissioning check and audit safety a few months after startup.

A HAZID's output is a list of hazards and possible major accident events that then need risk assessment and controls [2]. A HAZOP's output is a set of deviations and actions on a design that already exists [5]. NOPSEMA notes that HAZOP results describe causes and consequences of deviations, so they may need reworking before they fit a major accident risk assessment [2].

## A common mix-up

The abbreviation PHA means two different things. In US rules, process hazard analysis is the required study, and HAZOP is one of the methods allowed for it [4]. In HSE guidance, a preliminary hazard analysis is the first step of a hazard assessment, done during early process development and again for modifications [1].

## Where integrity problems show up

| Element or step | Integrity link | In the Library |
|---|---|---|
| HAZID prompts on corrosion and overpressure | NOPSEMA lists corrosion, overpressure and leaks among the general hazard prompts used at early stages [2] | [What is a corrosion risk assessment in FEED?](/library/corrosion-risk-assessment-in-design/) |
| HAZOP's weak spot on equipment damage | NOPSEMA notes HAZOP is less suitable for mechanical integrity failures [2] | [What is a damage mechanism review?](/library/damage-mechanism-review/) |
| From identified hazards to safety-critical equipment | UK offshore safety cases must show that measures, including safety and environmental-critical elements, are chosen to control each major accident risk [7] | [What are safety and environmental critical elements (SECEs)?](/library/safety-critical-elements/) |
| Accurate P&IDs and relief data for the full HAZOP | A HAZOP is only as good as its drawings and data [5]; relief design basis is required process safety information [4] | [What does a pressure relief valve do?](/library/pressure-relief-valve/) |
| Pre-commissioning check | HSE's fifth stage checks the plant before commissioning, including statutory requirements [1] | [What is a pre-startup safety review (PSSR)?](/library/pre-startup-safety-review/) |
| Repeating the studies after change | NOPSEMA expects hazard identification to be repeated after modifications [2]; HSE applies its stages to modifications too [1] | [What is management of change (MOC)?](/library/management-of-change/) |

Sources: HSE [1]; NOPSEMA [2]; 29 CFR 1910.119 [4]; University of Auckland [5]; HSE L154 [7].

## Sources

1. [Plant modification / Change procedures (COMAH technical measures), UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/comah/sragtech/techmeasplantmod.htm)
2. [Hazard Identification, Guidance Note N-04300-GN0107, Revision 5, National Offshore Petroleum Safety and Environmental Management Authority (NOPSEMA), Australia](https://www.nopsema.gov.au/assets/Guidance-notes/A98726.pdf)
3. [Out of control: Why control systems go wrong and how to prevent failure, HSG238, second edition, UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/pubns/priced/hsg238.pdf)
4. [29 CFR 1910.119, Process safety management of highly hazardous chemicals, paragraphs (d) and (e), eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)
5. [Hazard and Operability (HAZOP) Studies, University of Auckland](https://cdn.auckland.ac.nz/assets/ecm/documents/Hazard-Operability-Studies.pdf)
6. [IEC 61882:2016, Hazard and operability studies (HAZOP studies): Application guide (webstore page) (IEC 61882:2016, edition 2), International Electrotechnical Commission (IEC)](https://webstore.iec.ch/en/publication/24321), 2016-03-10
7. [The Offshore Installations (Offshore Safety Directive) (Safety Case etc) Regulations 2015: Guidance on Regulations, L154, first edition, UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/pubns/priced/l154.pdf)

Published by Winda Beacon (https://beacon.winda.ai).
