# What is a hydrostatic test?

> A hydrostatic test fills a pipeline, vessel or piping system with water and holds it above operating pressure to prove its strength and find leaks. For US pipelines, 49 CFR 192 Subpart J and 49 CFR 195 Subpart E set the test pressure, hold time and records, and the pressure reached caps the later operating pressure.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T11:53:52+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: LNG, Pipelines, Refining
- Canonical: https://beacon.winda.ai/library/hydrostatic-test/

## Why does it matter?

Passing a hydrostatic test does not prove a pipe is free of flaws. A 2013 study for the Pipeline and Hazardous Materials Safety Administration (PHMSA) explains that a test either makes a defect fail or shows that nothing weaker than the test pressure was left; smaller flaws survive, can grow in service and, if short and deep, can leak soon after restart [7]. The test still catches gross defects: the National Transportation Safety Board (NTSB) judged that a test would probably have revealed the defective pipe that ruptured in San Bruno, California, in 2010, which was never hydrostatically tested after installation in 1956 [8].

## How is a hydrostatic test done?

These steps and figures come from the US pipeline rules, 49 CFR 192 Subpart J for gas and 195 Subpart E for hazardous liquids [1][2]; plant equipment is covered further down.

1. **Isolate and instrument the section.** Liquid pipeline test records must include the pressure charts and instrument calibration data [2].
2. **Fill with the test medium.** Water is the default for hazardous liquid lines [2]. Gas lines may also use air, natural gas or inert gas that suits the pipe and, apart from natural gas, cannot burn [1].
3. **Raise the pressure and hold it.** Minimum hold times range from 1 to 8 hours, by pipeline type and stress level (table below) [1][2].
4. **Find leaks.** Every potentially hazardous leak must be found and eliminated before a gas segment operates [1].
5. **Keep people clear.** Above 50% of specified minimum yield strength (SMYS), gas operators must keep everyone but the test crew out of the area [1].
6. **Drain and dispose.** Test water must be disposed of so as to minimize damage to the environment [1].

## What do US pipeline rules require?

| Requirement | Gas pipelines (49 CFR 192 Subpart J) | Hazardous liquid pipelines (49 CFR 195 Subpart E) |
|---|---|---|
| When | Before a new, relocated or replaced segment operates (192.503) | Before operation, and after a segment is replaced, relocated or otherwise changed (195.302) |
| Medium | Liquid, air, natural gas or inert gas; water required near occupied buildings in Class 1 and 2 locations unless they are evacuated (192.503, 192.505) | Water, with narrow exceptions (195.306) |
| Pressure and hold | Steel at 30% SMYS or more: 8 h minimum; below 30% SMYS and at 100 pounds per square inch gauge (psig) or more: 1 h minimum (192.505, 192.507) | 125% of maximum operating pressure or more for 4 continuous h, plus 4 h at 110% or more if not visually inspected (195.304) |
| Spike test | Water; within the first 2 h, raised to 1.5 times the maximum allowable operating pressure (MAOP) or 100% SMYS, whichever is lower, for 15 min or more (192.506) | Not in Subpart E |
| Operating limit | MAOP no higher than test pressure divided by 1.1 to 1.5, by class location and installation date (192.619) | Maximum operating pressure no higher than 80% of test pressure (195.406) |
| Records | Useful life of the pipeline: medium, pressure, duration, charts, elevation changes, leaks and failures (192.517) | Latest test, kept while the facility is in use, with calibration data and temperature (195.310) |

Sources: eCFR, 49 CFR Parts 192 and 195, up to date as of 22 October 2026 [1][2][3][4].

Gas tests are capped more tightly than water tests: with air or inert gas, hoop stress may not exceed 75%, 50% and 40% of SMYS in Class 2, 3 and 4 locations, and with natural gas 30% [1].

Plant equipment is tested under its construction code; federal rules for breakout tanks, for example, point to the test sections of API 650, API 620 or ASME Section VIII [2]. In plants under the Occupational Safety and Health Administration (OSHA) process safety management standard, each test must be documented with date, person, equipment and result [9], and OSHA's 2017 refinery review lists a citation for pressure testing not done by an appropriately certified person [10].

## What does a passed test show, and what does it not show?

| A passed test shows | A passed test does not show |
|---|---|
| The section held the required pressure for the required time, with leaks found and fixed [1][2] | That no flaws remain: defects that would fail only above the test pressure survive [7] |
| Defects that would fail below the test pressure are gone, because they failed [7] | Where survivors are or how big; in-line inspection (ILI) can detect and classify many of them, and the study suggests combining the two [7] |
| A documented basis for the operating limit [3][4] | Future condition: survivors can grow by pressure-cycle fatigue, corrosion or stress corrosion cracking [7] |
| A margin that rises with the ratio of test to operating pressure [7] | Freedom from small leaks: short through-wall seam flaws may hold during the test [7] |

Sources: PHMSA-funded study, 2013, six case studies covering 2,096 miles of liquid pipelines [7].

The study also describes a "pressure reversal", where a near-critical flaw grows during the test and later fails at a lower pressure; it reports that one large enough to fail a line at operating pressure is extremely unlikely [7].

## Where integrity problems show up

| Decision or step at this stage | What it affects later | In the Library |
|---|---|---|
| Test pressure reached after construction | Caps operating pressure for the life of the line [3][4] | [Maximum allowable operating pressure](/glossary/maximum-allowable-operating-pressure/) |
| Test records kept complete | Gas transmission segments in high consequence areas and other listed locations need MAOP reconfirmation if test records are not traceable, verifiable and complete [5] | [What documents are handed over when a project is completed?](/library/handover-documentation/) |
| Construction test of new pipe in a high consequence area | Can count as the baseline integrity assessment, due within 10 years of installation [6] | [Baseline inspection](/glossary/baseline-inspection/) |
| Test failures recorded with their disposition | In 2010 PHMSA asked operators of large lines built in 2008 and 2009 to review test failures with welding and inspection records [1][11] | [What inspection records do codes require you to keep?](/library/inspection-record-requirements/) |
| Flaws that pass the test | Can grow in service, so time-dependent threats need retesting or ILI [7] | [What is in-line inspection (ILI) and pigging?](/library/in-line-inspection/) |

Sources: 49 CFR 192.517, 192.619, 192.624, 192.921, 195.406 [1][3][4][5][6]; PHMSA ADB-10-03, 2010 [11]; PHMSA-funded study, 2013 [7].

## Sources

1. [49 CFR Part 192, Subpart J, Test Requirements (192.501 to 192.517), eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-192/subpart-J)
2. [49 CFR Part 195, Subpart E, Pressure Testing (195.300 to 195.310), eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-195/subpart-E)
3. [49 CFR 192.619, Maximum allowable operating pressure: Steel or plastic pipelines, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-192/subpart-L/section-192.619)
4. [49 CFR 195.406, Maximum operating pressure, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-195/subpart-F/section-195.406)
5. [49 CFR 192.624, Maximum allowable operating pressure reconfirmation: Onshore steel transmission pipelines, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-192/subpart-L/section-192.624)
6. [49 CFR 192.921, How is the baseline assessment to be conducted?, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-D/part-192/subpart-O/section-192.921)
7. [Effectiveness of Hydrostatic Testing for Assessing the Integrity of ERW and Flash-weld Pipe Seams, Final Report No. 13-001 (K. M. Kolovich, J. F. Kiefner), Kiefner and Associates for Battelle, under US DOT agreement DTPH56-11-T-000003; hosted by PHMSA](https://primis.phmsa.dot.gov/rd/FileGet/7916/Task1_2-Effectiveness_of_Hydrostatic_Testing-KOLOVICH.pdf), 2013-01-15
8. [Pacific Gas and Electric Company Natural Gas Transmission Pipeline Rupture and Fire, San Bruno, California, September 9, 2010 (NTSB/PAR-11/01), US National Transportation Safety Board (NTSB)](https://www.ntsb.gov/investigations/AccidentReports/Reports/PAR1101.pdf)
9. [29 CFR 1910.119, Process safety management of highly hazardous chemicals, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)
10. [Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918), US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/sites/default/files/publications/OSHA3918.pdf)
11. [Pipeline Safety: Girth Weld Quality Issues Due to Improper Transitioning, Misalignment, and Welding Practices of Large Diameter Line Pipe (ADB-10-03), 75 FR 14243, Pipeline and Hazardous Materials Safety Administration (PHMSA), Federal Register via GovInfo](https://www.govinfo.gov/content/pkg/FR-2010-03-24/html/2010-6528.htm), 2010-03-24

Published by Winda Beacon (https://beacon.winda.ai).
