# What is mechanical integrity (MI)?

> Mechanical integrity (MI) is the program that keeps process equipment, from vessels and piping to relief devices and pumps, fit for service. It rests on written procedures, training, inspection and testing, correction of deficiencies and quality assurance. In the US it is part (j) of the Occupational Safety and Health Administration (OSHA) process safety rule, 29 CFR 1910.119.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T11:57:56+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: LNG, Refining, Upstream and offshore
- Canonical: https://beacon.winda.ai/library/mechanical-integrity/

## Why does it matter?

In refinery inspections under a national emphasis program launched in June 2007, OSHA found that failing to correct equipment deficiencies outside acceptable limits was one of the leading causes of process safety management (PSM) non-compliance [2]. Inspection finds problems, but the rule also requires fixing them [1]. Relief devices were cited most often, with piping circuits, pressure vessels and alarm systems next [2]. In one case cited, a leaking elbow in a hydrogen sulfide waste gas line stayed in service under an engineered clamp [2].

## What equipment does mechanical integrity cover?

The OSHA rule names six groups: pressure vessels and storage tanks; piping systems, including valves; relief and vent systems; emergency shutdown systems; controls, including sensors, alarms and interlocks; and pumps [1]. OSHA's process safety guide describes the aim as making sure critical equipment is designed and installed correctly and works properly [7].

OSHA's compliance guidance adds fire protection components, and calls a ranked list of equipment the first step of an MI program, so that items needing closer scrutiny stand out [1]. It frames MI as protecting the lines of defense: keeping chemicals contained and venting them safely first, then fire protection, dikes and drainage if a release happens [1].

## What does PSM mechanical integrity require?

| Paragraph of 29 CFR 1910.119 | Requirement | In practice |
|---|---|---|
| (j)(1) Application | Covers the six equipment groups [1] | The equipment list is the starting point [1] |
| (j)(2) Written procedures | Written procedures that keep process equipment sound over time [1] | OSHA cited procedures that did not set the number and location of thickness measurement points [2] |
| (j)(3) Training | Maintenance staff learn the process, its hazards and their own procedures [1] | Applies to each employee who maintains process equipment [1] |
| (j)(4) Inspection and testing | Follows recognized and generally accepted good engineering practice (RAGAGEP); frequency set by maker advice and good practice, more often if experience demands; each test recorded with date, person, equipment identifier, description and result [1] | Codes from the American Petroleum Institute (API), such as API 510, API 570 and API 580, are examples of inspection RAGAGEP for vessels and piping [2] |
| (j)(5) Equipment deficiencies | Deficiencies outside limits in the process safety information are corrected before further use, or in a safe and timely way with interim measures [1] | One of the leading causes of refinery non-compliance [2] |
| (j)(6) Quality assurance | New equipment suits the process as fabricated and is installed to design; spare parts and materials suit the process [1] | As-built drawings, certifications and materials records are kept, and gaskets, bolts and welding rods are checked in the field [1] |

## What do inspectors most often find?

OSHA's 2017 summary of its refinery program lists recurring MI gaps [2]:

- **Uncorrected deficiencies** in four groups: missing maintenance or repair, wrong installation such as incorrect sizing, missing protective systems such as relief devices, and weak structural support. [2]
- **Incomplete procedures** that did not fix thickness measurement locations or say how to handle anomalous data, such as wall readings that increase over time. [2]
- **Corrosion rates** not calculated to set inspection intervals, or measured rates above the expected rate left unaddressed. [2]
- **Corrosion under insulation** not inspected in a sulfur unit. [2]
- **Generic procedures** that missed site equipment; in one plant, hydrogen sulfide monitors and alarms were checked only after they malfunctioned. [2]

## Which other rules require mechanical integrity?

| Rule | Applies to | How it differs from OSHA (j) |
|---|---|---|
| Environmental Protection Agency (EPA), 40 CFR 68.73 | Program 3 processes under the Risk Management Program | Same six requirements and equipment groups [3] |
| Bureau of Safety and Environmental Enforcement (BSEE), 30 CFR 250.1916 | US offshore operations under safety and environmental management systems (SEMS) | Covers all equipment that prevents or mitigates uncontrolled releases, from design and procurement to modification; deficiencies beyond the maker's limits are corrected before further use; records carry the inspector's position and signature [4] |
| California, 8 CCR 5189.1(j) | Petroleum refineries in California | Inspection procedures must meet or exceed RAGAGEP, and the employer needs a process to evaluate new or updated codes and standards [5] |

## Where integrity problems show up

| Decision | Data it depends on | What goes wrong without it | In the Library |
|---|---|---|---|
| Putting equipment in the MI program | Piping and instrumentation diagrams and equipment lists | Gas monitors, flow and level alarms were inspected only when they failed [2] | [What should an inspection plan contain?](/library/inspection-plan/) |
| Setting thickness measurement locations and intervals | Corrosion rates and susceptible spots such as injection points, mixing points and dead legs | Corrosion rates were not calculated, and rates above expectation went unaddressed [2] | [What are condition monitoring locations (CMLs)?](/library/condition-monitoring-locations/) |
| Resolving anomalous readings | Thickness history at each location | Increasing wall readings were not investigated [2] | [What is an inspection data management system (IDMS)?](/library/inspection-data-management-system/) |
| Inspecting insulated equipment | Insulation condition and temperature cycling | Sulfur unit vessels and piping had no inspection for corrosion under insulation [2] | [What is corrosion under insulation (CUI)?](/library/corrosion-under-insulation/) |
| Re-checking old equipment when practice changes | New industry findings and material records | In Philadelphia in 2019, an elbow with high nickel and copper thinned in hydrofluoric acid service to 0.011 in (0.28 mm) and ruptured; industry guidance changed after 2003 research, but inspecting every component of existing circuits was not required [6] | [What is RAGAGEP (recognized and generally accepted good engineering practice)?](/library/ragagep/) |

Sources: OSHA 3918, 2017 [2]; CSB report 2019-04-I-PA, 2022 [6].

## Sources

1. [29 CFR 1910.119, Process safety management of highly hazardous chemicals (paragraphs (d) and (j), and Appendix C), eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)
2. [Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918-08), US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/Publications/OSHA3918.pdf)
3. [40 CFR 68.73, Mechanical integrity, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-40/chapter-I/subchapter-C/part-68/subpart-D/section-68.73)
4. [30 CFR 250.1916, What criteria for mechanical integrity must my SEMS program meet?, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-30/chapter-II/subchapter-B/part-250/subpart-S/section-250.1916)
5. [California Code of Regulations, Title 8, Section 5189.1, Process Safety Management for Petroleum Refineries (subsection (j), Mechanical Integrity), California Department of Industrial Relations (Cal/OSHA)](https://www.dir.ca.gov/title8/5189_1.html)
6. [Investigation Report: Fire and Explosions at Philadelphia Energy Solutions Refinery Hydrofluoric Acid Alkylation Unit (No. 2019-04-I-PA), US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/20/PES_Final_Report_Published_October_2022_r1.pdf?16845), 2022-10-11
7. [Process Safety Management (OSHA 3132), US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/sites/default/files/publications/osha3132.pdf)

Published by Winda Beacon (https://beacon.winda.ai).
