# How are pressure vessels inspected?

> Pressure vessels are inspected externally in service, internally during shutdowns, and with nondestructive tests such as ultrasonic thickness readings. Timing follows the measured damage and the governing code: usually API 510 in refining and chemicals and the National Board Inspection Code (NBIC) elsewhere, applied under state or national law.

- Label: Fact
- Type: Explainer
- Published: 2026-11-13T09:44:04+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-13
- Topics: LNG, Refining
- Canonical: https://beacon.winda.ai/library/pressure-vessel-inspection/

## Why does it matter?

In April 2017 a corroded pressure vessel in the steam system of a box plant in St. Louis, Missouri, failed at its bottom head; the explosion killed a worker nearby and threw the vessel several hundred feet onto a neighboring business, where three members of the public died [1][10]. The plant had known of corrosion in the vessel since 2004 but had no inspection program for it, and the city, which was responsible for inspecting pressure vessels there, never inspected it [1]. A 2012 repair had replaced only part of the corroded head [1].

## What does a pressure vessel inspection look at?

- **The records.** OSHA's guidance lists what an assessment needs: maker and National Board number, design code, materials, fabrication including post-weld heat treatment, and past inspections and repairs [2].
- **The outside, in service.** Visual examination covers large areas quickly and finds severe corrosion, erosion and hydrogen blistering [2]. A UK written scheme states whether each examination is made in or out of service [7].
- **The inside, at a shutdown.** OSHA's guidance focuses attention on vessels in deaerator, amine, wet hydrogen sulfide, ammonia and pulp digester service, on welds and the metal beside them, and on welds never post-weld heat treated [2].
- **The protective devices.** API 510 covers the relief devices that protect vessels [6]; a UK written scheme must cover every protective device [7].

## Which test methods are used?

OSHA's guidance names five methods in wide use by certified pressure vessel inspectors [2]:

| Method | What it finds | Main limit |
|---|---|---|
| Visual examination (VT) | General condition; severe corrosion, erosion and hydrogen blistering over large areas | Needs a clean surface and good light |
| Liquid penetrant testing (PT) | Flaws open to the surface, in any alloy, including austenitic stainless steel and nonferrous metals | Misses flaws that do not break the surface |
| Magnetic particle testing (MT), including the wet fluorescent variant (WFMT) | Surface and near-surface flaws in carbon and low-alloy steel; WFMT was the most effective method for cracking in pulp digesters | Magnetic steels only; most sensitive to flaws lying across the magnetic field; depth reach about 1.5 to 3 mm (about 1/16 to 1/8 inch), a crude estimate |
| Radiography (RT) | Flaws inside the wall, with their size in the plane of the image | Tight cracks show far less clearly than open voids; depth needs special techniques; radiation safety controls |
| Ultrasonic testing (UT) | Internal flaws, and wall thickness from the travel time of a sound pulse | In its basic form leaves no permanent record; newer equipment records signals |

Source: OSHA Technical Manual, Section IV, Chapter 3 [2].

OSHA's guidance adds that a safety assessment rests on "the largest flaw that may be missed, not the smallest one that can be found" [2]. See [How does ultrasonic thickness measurement work?](/library/ultrasonic-thickness-measurement/) and [Radiographic vs ultrasonic testing for welds](/library/radiography-vs-ultrasonic/).

## Who sets the rules and the timing?

- **US process safety rules.** For covered processes, OSHA requires inspections to follow recognized and generally accepted good engineering practice, at a frequency consistent with manufacturers' advice and good practice, or more often if experience demands; each one is recorded with date, inspector, equipment, method and results [4]. On timing, see How are inspection intervals set for vessels, piping and tanks? and What is risk-based inspection (RBI)?.
- **The in-service code.** API 510 serves refinery, petrochemical and chemical process vessels, and the NBIC serves other installations [3][6].
- **State and city law.** Missouri, for example, requires an external certificate inspection of each pressure vessel every two years, with internal inspection at the inspector's discretion, but exempts cities and counties with their own ordinance, as St. Louis was [1]. The National Board's NB-370 synopsis summarizes each jurisdiction's rules [8]. After 2017 the CSB recommended that St. Louis adopt NBIC Part 2 and require National Board commissioned in-service inspectors; it lists both as closed with acceptable action [10].
- **The UK.** Under the Pressure Systems Safety Regulations 2000, most systems need a written scheme of examination, drawn up or certified by a competent person, that covers protective devices and sets the nature and frequency of examinations; the competent person then carries them out [7].

## What happens with the results?

- **Thickness becomes a corrosion rate.** API 510 and the NBIC both use the general corrosion rate to time the next inspection [3]; OSHA cited refineries that never calculated rates, ignored rates above expectation or left rising readings uninvestigated [5]. See [Corrosion rate](/glossary/corrosion-rate/) and [Remaining life](/glossary/remaining-life/).
- **Cracks need an engineering assessment.** Judging a crack's severity takes fracture mechanics, with data on stresses, material properties and flaw size [2]. See [What is fitness-for-service (API 579-1/ASME FFS-1)?](/library/fitness-for-service/).
- **Deficiencies are corrected.** OSHA requires equipment outside acceptable limits to be fixed before further use, or promptly with measures that keep operation safe [4].
- **Repairs follow the code.** Repairs fall under API 510 or NBIC rules [3]; at St. Louis the CSB found the 2012 repair likely left metal below the required minimum thickness in place [1].

## Where integrity problems show up

| What it finds well | What it can miss or get wrong | In the Library |
|---|---|---|
| Weld cracking in amine and pulp digester service, found best by wet fluorescent magnetic particle testing on prepared surfaces [2] | Flaws below the surface when only surface methods are used, and flaws lying parallel to the magnetic field [2] | What is amine corrosion and amine cracking?, What is caustic stress corrosion cracking? |
| General wall loss from ultrasonic thickness readings [2] | Damage concentrated in one place: oxygen pitting and general corrosion thinned the St. Louis vessel's bottom head while its shell and upper head stayed relatively sound [1] | What is oxygen corrosion in water systems?, [What is pitting corrosion?](/library/pitting-corrosion/) |
| Advanced high temperature hydrogen attack with significant cracking [9] | Early-stage attack: the CSB called it very hard to find by inspection, with results that depend on technique and inspector skill (Anacortes, Washington, 2010) [9] | [What is high temperature hydrogen attack (HTHA)?](/library/high-temperature-hydrogen-attack/) |
| Visible external corrosion [2] | Corrosion under insulation where no one looked beneath it, cited by OSHA at refineries [5] | [What is corrosion under insulation (CUI)?](/library/corrosion-under-insulation/) |

Sources: CSB reports on St. Louis (2022) [1] and Anacortes (2014) [9]; OSHA Technical Manual [2]; OSHA 3918 (2017) [5].

## Sources

1. [Investigation Report: Loy-Lange Box Company Pressure Vessel Explosion (No. 2017-04-I-MO), US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/20/Loy_Lange_Box_Company_Report_-_Final.pdf?16806), 2022-07-29
2. [OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines, US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/otm/section-4-safety-hazards/chapter-3)
3. [NIST Special Publication 780, Guidelines for Pressure Vessel Safety Assessment (S. Yukawa), US National Institute of Standards and Technology (NIST)](https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication780.pdf)
4. [29 CFR 1910.119, Process safety management of highly hazardous chemicals, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)
5. [Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918), US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/Publications/OSHA3918.pdf)
6. [2025 Publications Catalog (entries for API 510 and RP 572) (API 510, 11th edition, October 2022; RP 572, 5th edition, November 2023), American Petroleum Institute (API)](https://www.api.org/-/media/files/publications/2025-catalog/2025_pubs%20catalog.pdf)
7. [Pressure systems: A brief guide to safety (INDG261, rev2), UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/pubns/indg261.pdf)
8. [NB-370, National Board Synopsis of Boiler and Pressure Vessel Laws, Rules and Regulations (all jurisdictions), National Board of Boiler and Pressure Vessel Inspectors (NBBI)](https://www.nationalboard.org/PrintAllSynopsis.aspx?Jurisdiction=Select)
9. [Investigation Report: Catastrophic Rupture of Heat Exchanger, Tesoro Anacortes Refinery (Report 2010-08-I-WA), US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/7/tesoro_anacortes_2014-may-01.pdf)
10. [Loy Lange Box Company Pressure Vessel Explosion (investigation page and recommendation status), US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/loy-lange-box-company-pressure-vessel-explosion-/)

Published by Winda Beacon (https://beacon.winda.ai).
