# Process safety vs occupational safety: what is the difference?

> Process safety prevents fires, explosions and toxic releases from process equipment; occupational safety prevents worker injuries, such as slips and falls. Occupational safety is also called personal safety. A low injury rate does not show that major accident hazards are under control, as the US Chemical Safety Board found at Texas City in 2005.

- Label: Fact
- Type: Explainer
- Published: 2026-11-14T12:02:06+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-14
- Topics: Refining, Upstream and offshore
- Canonical: https://beacon.winda.ai/library/process-vs-occupational-safety/

## Why does it matter?

At the Texas City, Texas, refinery, where an explosion and fire killed 15 workers and injured 180 in 2005, the US Chemical Safety and Hazard Investigation Board (CSB) found that a very low personal injury rate had given a misleading picture of process safety performance [1]. Between 2002 and 2004, loss of containment incidents at the site, a process safety measure that was tracked but not managed, rose 52%, from 399 to 607 a year [1]. Two years after the explosion, the UK Health and Safety Executive (HSE) reported that many offshore management monitoring systems leaned too heavily on occupational injury data and too little on early signs of major hazards [3].

## Process safety vs occupational safety at a glance

| | Process safety | Occupational (personal) safety |
|---|---|---|
| What it prevents | Fires, explosions and accidental chemical releases at process facilities, as defined by the Center for Chemical Process Safety and cited by the CSB [1] | Injuries to individual workers; the same CSB source gives slips, trips and falls as examples [1] |
| Typical event | Infrequent, but often with multiple injuries and deaths; OSHA wrote its 1992 process safety rule in response to such incidents [6] | Injuries and illnesses counted case by case and compared as a rate [1] |
| Main US rule | OSHA's process safety management standard, 29 CFR 1910.119, *Process Safety Management of Highly Hazardous Chemicals* [7] | OSHA workplace standards and injury records; the CSB noted OSHA's national inspection focus on sites with high injury rates [1] |
| Headline measure | Process safety indicators, leading and lagging, such as loss of containment events or overdue safety-critical work [4][5] | OSHA recordable injury and illness rate: cases per 100 full-time workers a year, based on 2,000 hours each [1] |
| What improvement work targets | Risk control systems: hazard analysis, mechanical integrity, change control, safety systems [4][7] | At Texas City, campaigns, goals and rewards aimed at worker behavior and personal safety metrics [1] |
| What can be missed if it is the only lens | Day-to-day injuries during routine tasks | Deterioration of containment and safety barriers before a major accident [1][3] |

Sources: CSB Texas City report, 2007 [1]; HSE KP3, 2007 [3]; HSE HSG254, 2006 [4]; OSHA FS-3896, 2016 [5]; OSHA CPL 03-00-021, 2017 [6]; 29 CFR 1910.119 [7].

## When is process safety the focus?

- **Where highly hazardous chemicals are present above threshold quantities,** which brings a process under the Occupational Safety and Health Administration (OSHA) process safety management standard [7].
- **When designing, changing or starting up plant,** through process hazard analysis, management of change and pre-startup safety review [7].
- **When setting maintenance and inspection priorities** for equipment that contains hazardous fluids and for safety systems; HSE's offshore program found poor understanding of how degraded plant can affect safety-critical elements in a major accident [3].
- **In reporting to senior leaders.** After Texas City, the CSB recommended that the company's senior executives use leading and lagging process safety indicators [1].

## When is occupational safety the focus?

- **For every task on site,** including tasks with no hazardous chemical involved, where slips, trips and falls are the typical concern [1].
- **When comparing workplaces or industries,** because the OSHA recordable rate is normalized for that purpose [1].
- **When selecting and monitoring contractors.** The process safety rule itself requires employers to evaluate a contractor's safety performance and to keep an injury and illness log for contract employees in process areas [7].

## How is each one measured?

OSHA describes two kinds of process safety metrics: lagging metrics, gathered after an incident above a set severity, and leading metrics, which show how key work processes and layers of protection are performing before an incident [5]. HSE guidance recommends pairing a leading and a lagging indicator for each critical risk control system, so that each checks the other [4]. HSE also warns that relying on failure data alone means weaknesses are found only after something goes wrong [4].

Occupational safety relies mainly on injury rates. The CSB notes that OSHA's recordable rate excludes fatalities and is normalized per 100 full-time workers, so that sites can be compared [1].

Reporting of process safety indicators has lagged. After Texas City, the CSB asked the American Petroleum Institute and the United Steelworkers to develop a standard with leading and lagging process safety indicators [1]; OSHA's 2016 fact sheet points readers to ANSI/API RP 754 on that subject [5]. In its 2014 report on the 2010 heat exchanger rupture in Anacortes, Washington, the CSB noted that neither the federal PSM rule nor the RMP rule required companies to use or report process safety indicators [2]. California's refinery rule, operative since 1 October 2017, now requires refineries to track them [8].

## A common mix-up

The mix-up is treating one safety number as a measure of both. At Texas City, the injury rate counted fatalities the same way as injuries and was, for 2003 to 2004, the only safety metric in the bonus plan, while process safety performance declined [1]. The CSB also found that regulators had leaned the same way: OSHA's focus on sites with high injury rates had drawn attention away from rare but catastrophic process incidents [1]. The same report found mechanical integrity gaps that had left process equipment to run to failure [1].

## Where integrity problems show up

| Element or step | Integrity link | In the Library |
|---|---|---|
| Counting loss of primary containment | OSHA lists unplanned releases as a lagging metric, recorded by number, containment level, cause and location [5]; at Texas City these events rose 52% in two years [1] | [What is asset integrity management in oil and gas?](/library/asset-integrity-management/) |
| Tracking overdue inspections and work orders | Sites in OSHA's Voluntary Protection Programs track inspections scheduled for relief valves, piping, vessels and tanks, overdue work orders and overdue safety-critical maintenance [5] | [What is mechanical integrity (MI)?](/library/mechanical-integrity/) |
| Watching safety-critical backlogs | HSE found poor understanding of how degraded plant affects safety-critical elements, and called for a common definition of maintenance backlog and deferrals [3] | [What are safety and environmental critical elements (SECEs)?](/library/safety-critical-elements/) |
| Testing instruments on time | An HSE example of a process safety indicator, cited by the CSB, is the share of instruments and equipment tested by the target date [1] | [What is a safety instrumented system (SIS)?](/library/safety-instrumented-system/) |
| Avoiding run to failure | The CSB found that mechanical integrity gaps at Texas City led to process equipment being run to failure [1] | [Preventive vs predictive vs corrective maintenance](/library/maintenance-strategies/) |
| Catching damage mechanisms | At Anacortes in 2010, high temperature hydrogen attack weakened a heat exchanger until it ruptured, killing 7 workers [2] | [What is high temperature hydrogen attack (HTHA)?](/library/high-temperature-hydrogen-attack/) |

Sources: CSB Texas City report, 2007 [1]; CSB Anacortes report, 2014 [2]; HSE KP3, 2007 [3]; OSHA FS-3896, 2016 [5].

## Sources

1. [Investigation Report: Refinery Explosion and Fire, Texas City, Texas, March 23, 2005, Report No. 2005-04-I-TX, US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/20/CSBFinalReportBP.pdf?13841)
2. [Investigation Report: Catastrophic Rupture of Heat Exchanger, Tesoro Anacortes Refinery, Anacortes, Washington, April 2, 2010, Report 2010-08-I-WA, US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/7/tesoro_anacortes_2014-may-01.pdf)
3. [Key Programme 3: Asset Integrity Programme, UK Health and Safety Executive (HSE), Offshore Division](https://www.hse.gov.uk/offshore/assets/docs/kp3.pdf)
4. [Developing process safety indicators: A step-by-step guide for chemical and major hazard industries, HSG254, UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/pubns/priced/hsg254.pdf)
5. [The Use of Metrics in Process Safety Management (PSM) Facilities, Fact Sheet FS-3896, US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/sites/default/files/publications/OSHA3896.pdf)
6. [CPL 03-00-021, PSM Covered Chemical Facilities National Emphasis Program, US Occupational Safety and Health Administration (OSHA)](https://www.osha.gov/sites/default/files/enforcement/directives/CPL_03-00-021.pdf), 2017-01-17
7. [29 CFR 1910.119, Process safety management of highly hazardous chemicals, eCFR, US Office of the Federal Register](https://www.ecfr.gov/current/title-29/subtitle-B/chapter-XVII/part-1910/subpart-H/section-1910.119)
8. [California Code of Regulations, Title 8, Section 5189.1, Process Safety Management for Petroleum Refineries, California Department of Industrial Relations](https://www.dir.ca.gov/title8/5189_1.html)

Published by Winda Beacon (https://beacon.winda.ai).
