# Refining vs petrochemicals: how do they connect?

> Refining turns crude oil mainly into fuels, while petrochemical plants turn hydrocarbons such as naphtha, ethane and propane into chemical building blocks. The two connect through shared streams: refineries supply naphtha, propylene from fluid catalytic crackers and aromatics from catalytic reformers, and steam crackers can send hydrogen and pyrolysis gasoline back.

- Label: Fact
- Type: Explainer
- Published: 2026-11-13T09:44:04+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-13
- Topics: Refining
- Canonical: https://beacon.winda.ai/library/refining-vs-petrochemicals/

## Refining vs petrochemicals at a glance

| | Refining | Petrochemicals |
|---|---|---|
| Main input | Crude oil, plus some condensate, natural gas liquids and unfinished oils [3] | Naphtha, ethane, propane, butane and gas oil; natural gas for ammonia and methanol [6][1] |
| Main output | Fuels: in 2023, US refineries made about 19.6 gallons of gasoline, 12.5 of distillate and 4.4 of jet fuel per 42-gallon barrel [3] | Ethylene, propylene, butadiene, benzene, toluene and xylenes, then polymers and other intermediates [1] |
| Core processes | Distillation, cracking, reforming, alkylation, hydrotreating, blending [2] | Steam cracking, chilled separation, chemical conversion [8] |
| Typical process temperatures | Crude heater outlet about 650 to 750 °F (343 to 400 °C) [8]; fluid catalytic cracker regenerator about 1,100 to 1,250 °F (590 to 675 °C) [9] | Cracking furnace coils about 1,400 to 1,600 °F (760 to 870 °C) [7] |
| Hydrogen balance | Net user: hydrotreating takes about 200 to 800 standard cubic feet per barrel treated, more than the reformer supplies [8][9] | Steam crackers make byproduct hydrogen that can go to refineries [1] |
| Main integrity drivers | Sulfur, chlorides and organic acids in crude; hot hydrogen [15][10][11] | Coke and carbon in furnace coils; reactive monomers in dead legs [7][12] |
| US process safety rule | Occupational Safety and Health Administration (OSHA) Process Safety Management standard (29 CFR 1910.119), with a refinery National Emphasis Program since 2007 [13] | Same standard; it covers, among others, processes with 10,000 pounds or more of flammable gas on site [14] |

## When is refining used?

- **To make fuels from crude at scale.** Gasoline, diesel and jet fuel make up most of a US refinery's output [3].
- **To upgrade the heavy part of the barrel.** Conversion units crack heavy fractions into lighter, higher-value ones [2].
- **To meet product specifications.** Hydrotreaters remove sulfur and nitrogen from jet fuel and diesel [8].
- **To supply some chemical feedstock.** In 2023, each US barrel yielded about 0.34 gallons of naphtha and 0.21 gallons of other oils for petrochemical feedstock [3], and refinery olefins such as propylene and butylenes are also sold as feedstock [4].

## When is petrochemical processing used?

- **To make ethylene.** Ethylene comes almost exclusively from steam crackers in the chemical sector [1].
- **To make the building blocks of plastics, fibers and rubber.** Demand for ethylene, propylene and aromatics follows those markets [1].
- **To use cheap light feeds.** An ethane cracker yields about 50% more high-value chemicals than a naphtha cracker, though mostly ethylene; naphtha gives more propylene and aromatics [1].
- **To make ammonia and methanol.** These come mainly from steam reforming of natural gas [1].

In 2017, petrochemical feedstock accounted for about 12% of global oil demand [1]. See [What is a petrochemical plant?](/library/petrochemical-plant/).

## Which streams connect a refinery and a petrochemical plant?

| Stream | From | To | Source |
|---|---|---|---|
| Naphtha | Refinery crude unit | Naphtha steam cracker | [1] |
| Propane and butanes | Refineries (for example, from the fluid catalytic cracker) and natural gas plants | Steam crackers | [5][4][6] |
| Ethane | Natural gas processing plants, not refineries | Ethane steam crackers | [4] |
| Propylene and butylenes | Refinery fluid catalytic cracker | Polymer and chemical units | [5][1] |
| Benzene, toluene and xylenes | Refinery fluid catalytic cracker and catalytic reformer | Aromatics and chemical units | [1] |
| Hydrogen | Steam cracker | Refinery hydrotreaters | [1] |
| Pyrolysis gasoline | Steam cracker | Refinery, for processing into gasoline components | [1] |

The catalytic reformer makes aromatics by stripping hydrogen from naphthenes in naphtha, and that hydrogen goes to the hydrotreaters; refineries still usually need a steam methane reformer or bought hydrogen to cover demand [9][1]. Because of these links, steam crackers are often built in the same industrial hub as refineries, even under different owners, to share feeds, utilities and logistics [1]. At the time of the International Energy Agency's 2018 report, about 40% of European naphtha cracking capacity sat inside integrated refinery and petrochemical complexes, against less than 20% of US naphtha cracking capacity [1].

## Where integrity problems show up

| Side | Unit / equipment | Typical integrity issue | In the Library |
|---|---|---|---|
| Refinery | Hot crude unit piping and heater tubes | Sulfidation; the US Chemical Safety and Hazard Investigation Board (CSB) states it is present at every refinery that runs crude | [Sulfidation](/library/sulfidation/) |
| Refinery | Crude unit overhead | Hydrochloric acid and ammonium chloride corrosion | Hydrochloric acid corrosion, [Ammonium chloride corrosion](/library/ammonium-chloride-corrosion/) |
| Both | Carbon steel in hot, high-pressure hydrogen service (for example, refinery hydrotreaters) | High temperature hydrogen attack; American Petroleum Institute Recommended Practice 941 (API RP 941) covers hydrogen service in both refineries and petrochemical plants | [High temperature hydrogen attack](/library/high-temperature-hydrogen-attack/) |
| Petrochemical | Cracking furnace coils | Coke buildup and carburization; the US Department of Energy (DOE) reported coil replacement every 2 to 7 years | Carburization |
| Petrochemical | Butadiene piping | Popcorn polymer growing in dead legs until the pipe ruptures | [Dead leg](/glossary/dead-leg/) |

Sources: CSB: Richmond final report (2015) [10], high temperature hydrogen attack safety alert (2016) [11], Port Neches news release (2022) [12]; DOE (2004) [7]; OSHA Technical Manual, Section IV, Chapter 2 (undated) [15].

On the refinery side, the mechanisms in the table trace back to compounds that arrive with the crude, such as sulfur, salts and acids [15][10]. On the cracker side, they trace back to high coil temperatures and the coke that forms inside the coils [7]. Hot hydrogen service appears in both.

## Sources

1. [The Future of Petrochemicals: Towards more sustainable plastics and fertilisers, International Energy Agency](https://www.iea.org/reports/the-future-of-petrochemicals), 2018-10-04
2. [Refining crude oil: the refining process, U.S. Energy Information Administration](https://www.eia.gov/energyexplained/oil-and-petroleum-products/refining-crude-oil-the-refining-process.php)
3. [Refining crude oil: inputs and outputs, U.S. Energy Information Administration](https://www.eia.gov/energyexplained/oil-and-petroleum-products/refining-crude-oil-inputs-and-outputs.php), 2024-06-20
4. [Uses of hydrocarbon gas liquids, U.S. Energy Information Administration](https://www.eia.gov/energyexplained/hydrocarbon-gas-liquids/uses-of-hydrocarbon-gas-liquids.php), 2023-12-26
5. [Fluid catalytic cracking is an important step in producing gasoline, U.S. Energy Information Administration, Today in Energy](https://www.eia.gov/todayinenergy/detail.php?id=9150), 2012-12-11
6. [Technical Support Document for the Petrochemical Production Sector: Proposed Rule for Mandatory Reporting of Greenhouse Gases, U.S. Environmental Protection Agency, Office of Air and Radiation](https://www.epa.gov/sites/default/files/2015-03/documents/subpartx-tsd-petrochem.pdf), 2008-09-09
7. [Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining, U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)](https://www.energy.gov/sites/prod/files/2013/11/f4/condition_assessment.pdf)
8. [Energy Bandwidth for Petroleum Refining Processes, U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)](https://www.energy.gov/sites/prod/files/2013/11/f4/bandwidth.pdf)
9. [AP-42, Section 5.1: Petroleum Refining, U.S. Environmental Protection Agency](https://www.epa.gov/sites/default/files/2020-09/documents/5.1_petroleum_refining.pdf)
10. [Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire, Report No. 2012-03-I-CA, U.S. Chemical Safety and Hazard Investigation Board](https://www.csb.gov/assets/1/20/chevron_final_investigation_report_2015-01-28.pdf)
11. [Safety Alert: Preventing High Temperature Hydrogen Attack (HTHA), U.S. Chemical Safety and Hazard Investigation Board](https://csb.gov/assets/1/20/safety_alert_htha_final1.pdf?16371=)
12. [CSB Releases Final TPC Report, U.S. Chemical Safety and Hazard Investigation Board](https://www.csb.gov/csb-releases-final-tpc-report-/), 2022-12-19
13. [CPL 03-00-004, Petroleum Refinery Process Safety Management National Emphasis Program, Occupational Safety and Health Administration](https://www.osha.gov/enforcement/directives/cpl-03-00-004), 2007-06-07
14. [Standard interpretation: Processes involving flammable liquids and gases (29 CFR 1910.119), Occupational Safety and Health Administration](https://www.osha.gov/laws-regs/standardinterpretations/1993-09-09-5), 1993-09-09
15. [OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes, Occupational Safety and Health Administration](https://www.osha.gov/otm/section-4-safety-hazards/chapter-2)

Published by Winda Beacon (https://beacon.winda.ai).
