# How does ultrasonic thickness measurement work?

> Ultrasonic thickness measurement finds the wall thickness of a pipe, vessel or tank from one side by timing a sound pulse reflected from the far wall. The gauge multiplies half the round-trip time by the speed of sound in the metal. ASTM E797 covers the manual contact pulse-echo method used on corroding equipment.

- Label: Fact
- Type: Explainer
- Published: 2026-11-13T09:44:04+09:00
- By: Jun Zhong
- Researched and drafted by: Beacon's AI newsroom
- Checked by: Jun Zhong on 2026-11-13
- Topics: Pipelines, Refining, Upstream and offshore
- Canonical: https://beacon.winda.ai/library/ultrasonic-thickness-measurement/

## Why does it matter?

A thickness reading describes the spot under the probe and nothing else. In 2019 the UK Health and Safety Executive (HSE) reported that an 8-inch relief line at a UK refinery ruptured and released about 75 tonnes of flammable material, although its wall was routinely tested at four locations [1]. The internal thinning sat very close to the failure point, where none of the four tests were made, and a neighboring relief line had similar damage that had also gone undetected [1]. HSE stated that for high-risk dead legs, spot ultrasonic readings alone are not adequate and a significant share of the line should be tested [1].

## How does the measurement work?

Ultrasonic testing (UT) uses high-frequency sound. In a pulse-echo set-up, a pulser drives a transducer, the transducer sends sound into the part, and the returning echoes are displayed against time; travel time maps directly to distance [2]. For thickness, the echo that matters comes from the back wall, so the sound crosses the wall twice [7].

```
thickness = sound velocity × round-trip time ÷ 2
```

A worked check with published laboratory values: a 2023 study calibrated a velocity of 5,928 m/s in a grade 45 steel and timed 3.373 microseconds (µs) on a 10.003 mm block. Half of 5,928 m/s × 3.373 µs is about 10.0 mm [7].

Three conditions affect whether the number can be trusted [4][5][6]:

- **Coupling.** Sound barely crosses an air gap, so a thin film of water, oil or glycerin sits between probe and surface [4].
- **Calibration.** The user calibrates instrument, transducer and set-up, preferably on a reference of the same material [5]. The 2023 study derived both the velocity and a zero offset from blocks of known thickness [7]. Because thickness is proportional to velocity in the formula, a velocity set for the wrong material shifts every reading by the same percentage.
- **Geometry and temperature.** ASTM E797 assumes a constant velocity through the part and mainly flat, parallel surfaces, and its scope ends at 93 °C (200 °F) [6].

## Which probes and techniques are used?

- **Single-element contact probes** for normal-beam work on fairly flat surfaces where near-surface resolution is not critical [3].
- **Dual-element probes**, with separate send and receive elements angled toward each other, suited to thin walls and reflectors close to the surface [3]. A 2003 report for the US Minerals Management Service (MMS) found 4 to 5 MHz dual-element gauges sensitive to small pits within their best thickness range [8].
- **Delay-line probes** for precise gauging of thin material; the delay line also shields the element on hot surfaces [3].
- **Echo-to-echo readings through coatings**, which the MMS report described for coatings that are well bonded and less than 6 mm thick [8].
- **Electromagnetic acoustic transducers (EMATs)**, which need no couplant and can work without contact at high temperature [11].
- **Scanning and corrosion mapping.** The MMS report called manual grid readings tedious and of limited accuracy, and used scanned mapping to improve accuracy; permanently bonded sensor strips give repeat readings at one critical area [8].

## How accurate is it, and what affects the reading?

On clean laboratory blocks of 3 to 20 mm, the 2023 system measured within about ±0.01 mm [7]. For hand-held gauges in the field, the MMS report gave a resolution of 0.1 mm and an accuracy of about ±0.5 mm [8]. Surface condition matters: conventional contact probes could not be used on externally corroded surfaces because of poor contact and scattering, and the ultrasonic techniques tested tended to show corrosion slightly deeper than it was, with smaller beams doing better [8]. A 2019 review by researchers at the US National Energy Technology Laboratory (NETL) adds that resolution depends on frequency and is often too coarse for small pits [9].

## Where integrity problems show up

| What it finds well | What it can miss or get wrong | In the Library |
|---|---|---|
| General wall loss at the reading point, measured from one side [6] | Very local thinning between reading points, as in the UK relief line rupture reported in 2019 [1] | What are condition monitoring locations (CMLs)?, [Dead leg](/glossary/dead-leg/) |
| Corrosion rates at fixed points read at intervals [10] | The fastest-corroding part of a circuit when no point is on it: at a refinery in Richmond, California, readings on high-silicon fittings did not show faster sulfidation of low-silicon straight pipe before a 2012 rupture [10] | [What is sulfidation (high-temperature sulfur corrosion)?](/library/sulfidation/) |
| Small pits, with dual-element probes in their best range [8] | Pits smaller than the frequency can resolve [9]; depth read slightly too deep on rough surfaces [8] | [What is pitting corrosion?](/library/pitting-corrosion/) |
| Wall thickness through well-bonded coatings, in echo-to-echo mode [8] | Readings on externally corroded surfaces with poor contact [8] | How do protective coatings prevent corrosion? |
| Thin walls and hot surfaces, with delay-line probes [3] | Surfaces above 93 °C (200 °F), outside the ASTM E797 practice [6]; a velocity set for the wrong material [5][7] | What are the main non-destructive testing (NDT) methods in oil and gas? |

Sources: HSE safety alert CEMHD2-2019 [1]; US Chemical Safety and Hazard Investigation Board (CSB) final report on the 2012 Richmond refinery fire, 2015 [10]; US Minerals Management Service report, 2003 [8]; Wright et al., 2019 [9]; ASTM E797/E797M-21 product page [6].

## Sources

1. [Catastrophic rupture of dead-leg pipe-work (Safety alert, Bulletin No. CEMHD2-2019), UK Health and Safety Executive (HSE)](https://www.hse.gov.uk/safetybulletins/catastrophic-rupture-dead-leg-pipe-work.htm), 2019-08-20
2. [Basic Principles of Ultrasonic Testing (NDE-Ed), Iowa State University, Center for Nondestructive Evaluation](https://www.nde-ed.org/NDETechniques/Ultrasonics/Introduction/description.xhtml)
3. [Transducer Types (NDE-Ed), Iowa State University, Center for Nondestructive Evaluation](https://www.nde-ed.org/NDETechniques/Ultrasonics/EquipmentTrans/transducertypes.xhtml)
4. [Couplant (NDE-Ed), Iowa State University, Center for Nondestructive Evaluation](https://www.nde-ed.org/NDETechniques/Ultrasonics/EquipmentTrans/Couplant.xhtml)
5. [Calibration Methods (NDE-Ed), Iowa State University, Center for Nondestructive Evaluation](https://www.nde-ed.org/NDETechniques/Ultrasonics/CalibrationMeth/calibrationmethods.xhtml)
6. [ASTM E797/E797M-21, Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method (product page, Scope and Significance) (E797/E797M-21 (listed as active)), ASTM International](https://www.astm.org/e0797_e0797m-21.html)
7. [Ultrasonic Thickness Measurement Method and System Implementation Based on Sampling Reconstruction and Phase Feature Extraction (W. Gong et al.), Sensors 23(22):9072, MDPI, via PubMed Central](https://pmc.ncbi.nlm.nih.gov/articles/PMC10675015/), 2023-11-09
8. [Evaluation of Methods for Detecting and Monitoring of Corrosion and Fatigue Damage in Risers (M. Lozev, B. Grimmett, E. Shell, R. Spencer), final report, Technical Assessment Program project 433, US Minerals Management Service (now Bureau of Safety and Environmental Enforcement, BSEE)](https://www.bsee.gov/sites/bsee.gov/files/tap-technical-assessment-program//433aa.pdf), 2003-11-04
9. [Corrosion Sensors for Structural Health Monitoring of Oil and Natural Gas Infrastructure: A Review (R. F. Wright et al.), Sensors 19(18):3964, MDPI, via PubMed Central](https://pmc.ncbi.nlm.nih.gov/articles/PMC6767297/), 2019-09-13
10. [Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire, US Chemical Safety and Hazard Investigation Board (CSB)](https://www.csb.gov/assets/1/17/Chevron_Final_Investigation_Report_2015-01-28.pdf?15397), 2015-01-28
11. [Electromagnetic Acoustic Transducers (EMATs) (NDE-Ed), Iowa State University, Center for Nondestructive Evaluation](https://www.nde-ed.org/NDETechniques/Ultrasonics/EquipmentTrans/emats.xhtml)

Published by Winda Beacon (https://beacon.winda.ai).
