Skip to content
Beaconby Winda
FactOil, Gas and Chemicals Basics · Facilities and processes

How is liquefied natural gas (LNG) made?

·13 sources

Short answer

Liquefied natural gas (LNG) is made by cooling cleaned natural gas to about -162 °C (-260 °F), where it turns liquid at atmospheric pressure. Pretreatment removes water, carbon dioxide, sulfur compounds, mercury and heavy hydrocarbons; refrigerant cycles liquefy it; insulated tanks hold it until loading onto ships. US safety standards for LNG facilities are in 49 CFR Part 193.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

What happens to the gas before it is liquefied?

Feed gas reaches a liquefaction plant by pipeline, according to the US Energy Information Administration (EIA) and the US Department of Energy 3,2. It must be cleaned further, because some components form solids during cooling, damage equipment or cause internal corrosion 6.

A US Gulf Coast liquefaction project reviewed in a 2019 environmental impact statement by the Federal Energy Regulatory Commission (FERC) lists four pretreatment systems in this order: mercury removal, acid gas removal, molecular sieve dehydration and heavy hydrocarbon removal 4. The table gives the reason for each step and limits published in a 2019 industry article 5.

ContaminantWhy it is removedCommon removal methodExample limit at the cold section (2019 article)
MercuryAttacks aluminum brazed heat exchangers by liquid metal embrittlementNon-regenerative guard beds (metal sulfide or sulfur-impregnated carbon)0.01 µg per normal cubic meter
Carbon dioxideCan form solids during cooling 6; also a product purity limitAmine solvent, often promoted methyldiethanolamine (MDEA)Below 50 parts per million by volume (ppmv)
Hydrogen sulfide and total sulfurSulfur specification of the productAmine unit; molecular sieves for some sulfur compoundsBelow 4 ppmv H2S; below 30 ppmv total sulfur
WaterFreezes in the cryogenic sectionMolecular sieve bedsBelow 0.1 ppmv
Heavy hydrocarbons (pentanes and heavier, benzene)High freezing points; can solidify during liquefactionAdsorption or a liquids recovery stepBelow 0.1 mol% pentanes and heavier; below 1 ppmv benzene

Sources: FERC (2019) for the sequence 4; Mokhatab et al., Gas Processing & LNG (2019) for reasons, methods and limits 5; Gao et al. (2022) 6.

How is the gas cooled to a liquid?

Liquefaction takes place in one or more parallel units called trains 4. Each train uses compressors to drive refrigerants that pull heat out of the gas in stages until it condenses 4,3. Gao et al. (2022) group the processes into three families 6:

Cycle familyHow it worksWhere it appears 6
CascadeUsually three separate cycles with pure refrigerants (propane, ethylene, methane), each at a lower temperature levelUsed from the early 1960s
Mixed refrigerantOne blend of light hydrocarbons follows the cooling curve of the gas more closely; often precooled with propaneMainly adopted by base-load plants after the 1980s
ExpanderExpansion of nitrogen or methane through turbines provides refrigerationLower efficiency than cascade or mixed refrigerant cycles

The 2019 FERC example uses two propane-precooled mixed refrigerant trains, each rated at a nominal 5 million tonnes per annum, with gas turbines driving the refrigerant compressors 4. Liquefaction consumes part of the feed: from its survey data, EIA estimates that 7% to 15% of the gas delivered to US export plants is used to run the equipment 3.

How is LNG stored at the plant?

As a liquid, natural gas takes up about 1/600th of its gas volume, so plants keep it in specially insulated, refrigerated tanks 1. Heat always leaks in through the insulation, and internal pumps add energy, so some liquid evaporates; US regulations call the vapor that leaves the tank "boil-off gas" 8.

How is LNG loaded onto ships?

Pumps inside the storage tanks send LNG through insulated transfer lines to the berth, where it is loaded into double-hulled carriers 4,2. Cryogenic arms or hoses make the ship-to-shore connection; emergency release couplers allow a quick disconnection and emergency shutdown systems stop the transfer 7. Flares burn excess gas during maintenance, startup, shutdown and upsets; the 2019 FERC example has four flares on one tower 4.

A typical US export cargo holds the equivalent of about 3.0 to 3.7 billion cubic feet of gas, roughly 62,000 to 77,000 metric tons of LNG 2. The 2019 FERC example allows carriers of up to 208,000 cubic meters 4. At the receiving end, terminals warm the LNG back into gas for pipeline delivery 1.

Which US rules cover LNG plants?

Federal safety standards for LNG facilities used in pipeline transportation of gas are in 49 CFR Part 193 (Title 49 of the Code of Federal Regulations), administered by PHMSA 9. Its subparts run from siting, design and construction through operations, maintenance, training, fire protection and security, and it incorporates NFPA 59A (2001 and 2006 editions) by reference 9. Part 193 does not apply to LNG facilities in navigable waters, and for marine cargo transfer it covers mainly siting 10.

One construction rule, 49 CFR 193.2321, requires 100% nondestructive examination, under the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, of welds on load-bearing curved shells exposed to cryogenic temperatures 9. The 2019 example project also went through a federal environmental review led by FERC, with the US Department of Energy as a cooperating agency 4.

Where integrity problems show up

Unit or equipmentTypical integrity issueIn the Library
Acid gas removal (amine) unit in pretreatmentCorrosion and cracking in amine service; in 1986 OSHA cited survey data showing cracking in about 60% of 24 refinery amine absorbersWhat is amine corrosion and amine cracking?
Cryogenic tanks, piping and any carbon steel that LNG can reachBrittle fracture: carbon steels lose toughness at cryogenic temperatures; a 1944 LNG tank failure in Cleveland, Ohio, killed 128 people, and suspicion fell on its 3.5% nickel steelWhat is brittle fracture?
Welds on cryogenic load-bearing shellsWeld flaws; US rules require 100% nondestructive examination of these weldsWhat are the main non-destructive testing (NDT) methods in oil and gas?
Insulated lines in cold or cycling serviceCorrosion under insulation where moisture condenses, most often between -12 and 177 °C (10 and 350 °F) or in service that cycles through that rangeWhat is corrosion under insulation (CUI)?

Sources: FERC (2019) 4; Occupational Safety and Health Administration (OSHA) memorandum of 11 April 1986 12; US Particle Accelerator School cryogenic safety lecture, Fermi National Accelerator Laboratory (2021) 11; 49 CFR 193.2321 9; American Institute of Chemical Engineers Center for Chemical Process Safety, Process Safety Beacon (June 2019) 13.

Common questions

Is LNG the same as natural gas liquids (NGLs)?
No. LNG is mainly methane cooled until it becomes liquid (40 CFR 98.238). NGLs such as ethane, propane and butanes are heavier hydrocarbons separated from raw gas at a gas processing plant; see [What does a gas processing plant do?](/library/gas-processing-plant/).
What is boil-off gas?
It is the gas that vents from LNG storage tanks as heat leaks through the insulation and pumps add energy to the liquid (40 CFR 98.238).
Why is mercury removed if it is only present in traces?
Mercury can embrittle the aluminum brazed heat exchangers used in the cold section, which can cause serious structural damage (Mokhatab et al., 2019).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Liquefied Natural Gas (LNG) Overview · Pipeline and Hazardous Materials Safety Administration (PHMSA) ·
  2. 2.Liquefied Natural Gas Value Chain (fact sheet) · U.S. Department of Energy, Office of Fossil Energy
  3. 3.Natural gas explained: Liquefied natural gas · U.S. Energy Information Administration ·
  4. 4.Gulf LNG Liquefaction Project, Final Environmental Impact Statement (FERC/EIS-0290F), front matter and Chapter 1 · Federal Energy Regulatory Commission, with U.S. Department of Energy
  5. 5.Gas pretreatment considerations for LNG plants feeding with pipeline-quality gas · Gas Processing & LNG (S. Mokhatab, S. Northrop, R. Palla, B. Sharma)
  6. 6.The Design and Optimization of Natural Gas Liquefaction Processes: A Review (Energies 15(21), 7895, doi:10.3390/en15217895) · MDPI Energies (L. Gao, J. Wang, M. Binama, Q. Li, W. Cai)
  7. 7.About LNG · GIIGNL (International Group of Liquefied Natural Gas Importers)
  8. 8.40 CFR 98.238, Definitions (Subpart W, Petroleum and Natural Gas Systems) · Electronic Code of Federal Regulations (eCFR)
  9. 9.49 CFR Part 193, Liquefied Natural Gas Facilities: Federal Safety Standards · Electronic Code of Federal Regulations (eCFR)
  10. 10.49 CFR 193.2001, Scope of part · Electronic Code of Federal Regulations (eCFR)
  11. 11.Lecture 16: Cryogenic Safety (US Particle Accelerator School) · Fermi National Accelerator Laboratory, USPAS (J.G. Weisend II)
  12. 12.Potentially Hazardous Amine Absorber Pressure Vessels Used in Refinery Processing (memorandum) · Occupational Safety and Health Administration ·
  13. 13.Process Safety Beacon: Corrosion Under Insulation · AIChE Center for Chemical Process Safety