Skip to content
Beaconby Winda
FactAsset Integrity Management · Pipeline integrity

What is pipeline integrity management?

·12 sources

Short answer

Pipeline integrity management is an operator's ongoing cycle of finding threats, assessing pipe condition, repairing defects and preventing new damage. Work is ranked by risk. In the US, 49 CFR 192 Subpart O (gas transmission) and 49 CFR 195.452 (hazardous liquids) require written programs where a failure could affect high consequence areas.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

On July 25, 2010, a 30-inch crude oil pipeline ruptured in a wetland near Marshall, Michigan, releasing an estimated 843,444 gallons of oil into the wetland, Talmadge Creek and the Kalamazoo River 7. The rupture ran along a 51.6-inch crack-like feature that an in-line inspection had found in 2005, yet for nearly 5 years the integrity management program did not identify it as a threat 7. The National Transportation Safety Board (NTSB) found that the program relied on a single inspection technology and did not account for tool inaccuracy, actual wall thickness or the interaction of cracks and corrosion 7. US liquid pipeline rules now in force require operators to consider uncertainties in reported in-line inspection results explicitly 5.

What are the steps of a pipeline integrity management program?

The US regulator, the Pipeline and Hazardous Materials Safety Administration (PHMSA), sums up the duty as to "identify, prioritize, assess, evaluate, repair and validate" the integrity of covered pipe 1. The federal program elements cover these steps 3,5:

  1. Find the covered pipe: segments in, or that could affect, a high consequence area (HCA). 1,3,5
  2. Gather and integrate data, then identify threats, such as corrosion, cracking, manufacturing defects and outside force. 1,3,5
  3. Assess risk and rank segments for assessment. 1,3,5
  4. Assess condition with in-line inspection, pressure testing, direct assessment or other approved methods. 1,3,5
  5. Repair or mitigate anomalies on a set schedule, and add preventive measures. 1,3,5
  6. Reassess and re-evaluate at set intervals, using what was learned. 1,3,5
  7. Measure performance and keep records for the life of the pipeline. 1,3,5

API Recommended Practice (RP) 1160 (3rd edition, February 2019, reaffirmed March 2024) describes this process for hazardous liquid lines 11, and ASME B31.8S, in the 2018 edition incorporated into federal rules, does so for gas 12.

How do the US gas and liquid rules compare?

Gas transmission: 49 CFR 192 Subpart OHazardous liquid: 49 CFR 195.452
Pipe coveredSegments located in an HCA 3Pipe that could affect an HCA, unless a risk assessment shows it cannot 5
What makes an HCAClass 3 or 4 locations, or an impact circle with 20 or more occupied buildings or an identified site 3Navigable waterways, high population and other populated areas, unusually sensitive areas 4
Programs dueDecember 17, 2004 1March 31, 2002, or February 18, 2003, depending on the operator's mileage 2
Newly identified HCAAssess within 10 years 3Add to plan within 1 year, assess within 5 years 5
Assessment methodsIn-line inspection, pressure or spike test, direct examination, guided wave, direct assessment (corrosion and stress corrosion cracking only), other technology 3In-line inspection where practicable, with crack tools where cracks are a threat; otherwise pressure test, external corrosion direct assessment or other technology 5
ReassessmentAt most 7 calendar years by an allowed method; longer intervals need a confirmatory direct assessment within 7 years 3Five-year intervals, not over 68 months 5
RecordsUseful life of the pipeline 3Useful life of the pipeline 5

Source: eCFR, up to date as of 22 Oct 2026 3,4,5; PHMSA program pages 1,2.

How is a pipeline's condition assessed?

PHMSA's integrity assessment fact sheet lists in-line inspection tools that use magnetic flux leakage, transverse flux and ultrasonic waves to find corrosion, cracks and other anomalies, plus geometry tools that measure deformation 10. It notes that many tools need pipe of at least 6 inches and that hydrostatic testing is used instead of, or alongside, tool runs 10. Gas rules allow direct assessment only for external or internal corrosion and stress corrosion cracking, and both rules require operators to allow for in-line inspection uncertainty 3,5.

What happens outside high consequence areas?

On December 11, 2012, a 20-inch gas transmission line ruptured near Sissonville, West Virginia, in a Class 2 area outside any HCA, so it was not in the operator's integrity management program 6. The NTSB found more than 70% wall loss from external corrosion and noted that the line had not been inspected or tested after 1988 6. Federal gas rules now also require assessments of certain segments outside HCAs, including Class 3 and 4 locations and moderate consequence areas, with initial assessments due by July 3, 2034, and reassessment at least every 10 years 9.

Where integrity problems show up

DecisionData it depends onWhat goes wrong without it
Which segments are coveredPopulation, buildings, identified sites and sensitive areas around the line 3,4Sissonville (2012): a segment outside any HCA, not inspected or tested after 1988, ruptured 6
How to act on in-line inspection resultsReported anomalies with tool tolerance, validated wall thickness and interacting defects 5,7Marshall (2010): a crack-like feature reported in 2005 was not treated as a threat 7
Which tool to runThreats on the segment; crack threats need crack-capable tools 5Marshall (2010): crack management relied on one inspection technology 7
Whether findings apply to similar pipeCorrosion and crack findings with material, coating and environment 3Sissonville (2012): corrosion found by 2009 inspections of two adjacent lines was not adequately considered for the line that failed 6
How to judge internal corrosionGas quality, liquid sampling and internal corrosion monitoring results 3Carlsbad (2000): the NTSB found monitoring and sampling would likely have shown the corrosion potential 8

Sources: NTSB/PAR-12/01, 2012 7; NTSB/PAR-14/01, 2014 6; NTSB/PAR-03/01, 2003 8; 49 CFR 192 Subpart O and 195.452 3,5.

Common questions

How is pipeline integrity management different from asset integrity management?
Pipeline integrity management is the pipeline-specific form, built around high consequence areas and the assessment methods in federal pipeline rules. Inside US refineries, process safety reviews by the Occupational Safety and Health Administration (OSHA) point instead to in-service inspection codes such as API 510 for vessels and API 570 for piping. See [What is asset integrity management in oil and gas?](/library/asset-integrity-management) and [Piping vs pipeline: what is the difference?](/library/piping-vs-pipeline).
Is every US pipeline under these rules?
No. Subpart O and 195.452 apply to segments in or affecting HCAs; gas rules add assessments for some segments outside HCAs under 49 CFR 192.710.
What triggers an immediate repair?
Both rules list immediate repair conditions, such as metal loss deeper than 80% of the nominal wall or a dent on the top of the pipe with metal loss or cracking. Until it is repaired, the operator must lower the pressure or shut the line down. See [What happens after an in-line inspection run?](/library/ili-anomaly-response).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Gas Transmission Integrity Management (GT IM) Overview · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
  2. 2.Hazardous Liquid Integrity Management (HL IM) · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
  3. 3.49 CFR Part 192, Subpart O, Gas Transmission Pipeline Integrity Management · eCFR, US Office of the Federal Register
  4. 4.49 CFR 195.450, Definitions (high consequence area) · eCFR, US Office of the Federal Register
  5. 5.49 CFR 195.452, Pipeline integrity management in high consequence areas · eCFR, US Office of the Federal Register
  6. 6.Pipeline Accident Report: Columbia Gas Transmission Corporation Pipeline Rupture, Sissonville, West Virginia, December 11, 2012 (NTSB/PAR-14/01) · US National Transportation Safety Board (NTSB)
  7. 7.Pipeline Accident Report: Enbridge Incorporated Hazardous Liquid Pipeline Rupture and Release, Marshall, Michigan, July 25, 2010 (NTSB/PAR-12/01) · US National Transportation Safety Board (NTSB)
  8. 8.Pipeline Accident Report: Natural Gas Pipeline Rupture and Fire Near Carlsbad, New Mexico, August 19, 2000 (NTSB/PAR-03/01) · US National Transportation Safety Board (NTSB)
  9. 9.49 CFR 192.710, Transmission lines: Assessments outside of high consequence areas · eCFR, US Office of the Federal Register
  10. 10.Fact Sheet: Integrity Assessment · US Pipeline and Hazardous Materials Safety Administration (PHMSA), Pipeline Safety Stakeholder Communications
  11. 11.2025 Publications Catalog (entry for RP 1160) (RP 1160, 3rd edition, February 2019, reaffirmed March 2024) · American Petroleum Institute (API)
  12. 12.49 CFR 192.7, What documents are incorporated by reference partly or wholly in this part? (incorporates ASME B31.8S-2018) · eCFR, US Office of the Federal Register