What does a pressure relief valve do?
A pressure relief valve opens automatically when system pressure reaches a set point, venting fluid to stop overpressure, then recloses as pressure falls. ASME Boiler and Pressure Vessel Code Section XIII sets rules for overpressure protection devices, and API Standard 520 covers sizing, selection and installation in refineries and related plants.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
How does a pressure relief valve work?
In the most common design, a spring presses a disc onto a seat at the valve inlet 1,2. When pressure under the disc reaches the set pressure, it overcomes the spring, the valve lifts and fluid escapes; when pressure falls back to the reseating point, the valve closes again 1.
How far and how fast the valve opens depends on the service 1,2. A safety valve, used on steam or vapor, pops fully open almost at once; a relief valve, used on liquid, opens further as pressure keeps rising; and a safety relief valve is built to work in either service 1.
Released fluid goes to a safe discharge point or, in many refineries, through a closed header to a knockout drum that separates liquid from vapor, and on to a flare 1,2. OSHA's manual lists the causes they must handle, such as loss of cooling or reflux, fire, heater malfunction, control failures, exchanger tube failure and thermal expansion of trapped liquid 2.
What are the main types of pressure relief device?
| Device | How it works | Recloses? | Where it fits |
|---|---|---|---|
| Direct spring-loaded valve | A spring holds the disc shut until inlet pressure overcomes it | Yes | General service; balanced bellows versions are used where back pressure is expected |
| Pilot-operated valve | System pressure holds the main disc shut; a small pilot valve vents that pressure at the set point so the main valve opens | Yes | High-pressure service with narrow margins; tighter seat close to set pressure |
| Rupture disk | A thin disk bursts at its rated pressure | No, stays open | Where a spring valve is unsuitable, or upstream of a valve to shield it from corrosive or clogging fluid |
| Weight-loaded pressure-vacuum vent | A weight, not a spring, holds the vent shut until tank pressure or vacuum lifts it | Yes | Atmospheric and low-pressure storage tanks |
Sources: National Board PRD inspection guide 1; OSHA Technical Manual 2; ASME Section XIII product page 3; API 2025 Publications Catalog 5; Valve Magazine, 2024 9.
Because system pressure, not a spring, holds a pilot-operated valve shut, its seat stays tight closer to the set point, so equipment can run nearer its maximum allowable working pressure 9. Its small pilot tubing can clog in dirty service, and fast pressure swings at start-up can make it lift and leak 9. When a rupture disk sits upstream of a relief valve, a pressure gauge or telltale in the space between them shows whether the disk has burst 1.
Why is a relief valve safety-critical?
The National Board's inspection guide describes pressure relief devices as the last line of defense, the protection left when operating controls and other safety devices have failed 1. In processes covered by OSHA's process safety management (PSM) standard, relief and vent systems and devices are one of the six equipment groups that need a mechanical integrity program (29 CFR 1910.119(j)(1)(iii)), and the process safety information must include the relief system design and its design basis (29 CFR 1910.119(d)(3)(i)(D)) 6.
In OSHA's 2017 review of its refinery PSM emphasis program, relief devices were the equipment most frequently cited for deficiencies, ahead of piping circuits, pressure vessels and alarms 7. Recurring findings included missing relief devices, undersized valves, wrong set points, high back pressure, devices in places that could not be reached and no written design basis for the relief system 7.
A blocked relief path can be fatal. In a 2013 incident at an olefins plant in Geismar, Louisiana, a reboiler cut off from its relief device by block valves was heated, its shell ruptured, two workers died and 167 people were injured; the US Chemical Safety and Hazard Investigation Board (CSB) found that the valves and the controls on them had not been through adequate management of change 8. For how facilities identify and manage such equipment, see What are safety and environmental critical elements (SECEs)?.
Which codes and standards apply?
ASME added Section XIII, Rules for Overpressure Protection, to its Boiler and Pressure Vessel Code in the 2021 edition, and the current product page lists a 2025 edition 3,4. Its scope takes in several device types (relief valves, spring-actuated non-reclosing devices, pin-actuated devices and rupture disks), and it also deals with certifying their capacity, marking them with the ASME mark, installing them, and protecting a system from overpressure through its design 3.
| Stage | Document | What it covers |
|---|---|---|
| Overpressure causes and relief loads | API Standard 521 | Pressure-relieving and depressuring systems, including flares and vent stacks |
| Sizing and selection | API Standard 520, Part I | Relief devices that protect unfired pressure vessels and related equipment |
| Purchase | API Standard 526 | Flanged steel spring-loaded and pilot-operated relief valves |
| Construction and certification | ASME BPVC Section XIII | Device rules and capacity certification |
| Installation | API Standard 520, Part II | Inlet and discharge arrangements |
| Seat tightness test | API Standard 527 | Leakage testing of closed valves |
| In-service inspection and repair | API RP 576 | Spring-loaded and pilot-operated valves, rupture disks, pin devices and tank vents |
| Process safety (US) | 29 CFR 1910.119 | Relief design basis and mechanical integrity in covered processes |
Sources: ASME 3; API 2025 Publications Catalog, scope descriptions only 5; eCFR 6.
Where integrity problems show up
| Location or condition | Typical integrity issue | In the Library |
|---|---|---|
| Valve internals | Corrosion of the disc holder and guides stops the valve working properly, so it may not open at set pressure | What is corrosion? |
| Valve inlet and outlet | Plugging, fouling or solids stop the valve opening or reseating; steady leakage builds scale at the outlet | What is mechanical integrity (MI)? |
| Relief path | A closed block valve between the equipment and its relief device | What is management of change (MOC)? |
| Valves set too close to operating pressure or facing high back pressure | Chatter that can damage the valve and the connected piping and cut relief capacity | What is mechanical and vibration fatigue? |
| Relief system design | Missing or undersized devices, wrong set points and no documented design basis | What is process safety management (PSM)? |
Sources: OSHA Technical Manual, Section IV, Chapter 2 2; National Board PRD inspection guide 1; OSHA 3918, 2017 7; CSB, 2016 8.
Common questions
- What is the difference between a safety valve and a relief valve?
- A safety valve is meant for steam or vapor and pops fully open, while a relief valve is meant for liquid and opens in proportion to the pressure rise. A safety relief valve can serve either way, and "pressure relief valve" is the general term for all three.
- Is a rupture disk a pressure relief valve?
- No. A rupture disk is a non-reclosing pressure relief device: once it bursts it stays open and must be replaced, whereas a valve recloses.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.NBIC Pressure Relief Device (PRD) Inspection Guide (draft) · National Board of Boiler and Pressure Vessel Inspectors
- 2.OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes · US Occupational Safety and Health Administration (OSHA)
- 3.BPVC.XIII, BPVC Section XIII, Rules for Overpressure Protection (product page) (2025) · American Society of Mechanical Engineers (ASME)
- 4.2021 ASME Boiler and Pressure Vessel Code (2021) · American Society of Mechanical Engineers (ASME)
- 5.2025 Publications Catalog (Refining: Pressure-Relieving Systems for Refinery Service; Inspection of Refinery Equipment) · American Petroleum Institute (API)
- 6.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
- 7.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
- 8.CSB Releases Final Case Study into 2013 Explosion and Fire at Williams Olefins Plant in Geismar, Louisiana · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 9.Fundamental Operation of Pilot-Operated Safety Relief Valves (W. L. Cheong) · Valve Magazine, Valve Manufacturers Association ·