What is a pressure vessel?
A pressure vessel is a closed container for gas or liquid designed to operate above 15 pounds per square inch gauge (psig), as defined in 29 CFR 1910.106. US vessels are mostly built to ASME Boiler and Pressure Vessel Code Section VIII, which most states adopt into law, and inspected under API 510 or the National Board Inspection Code.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
What counts as a pressure vessel?
The US Occupational Safety and Health Administration (OSHA) sorts containers by design pressure. Under 29 CFR 1910.106, a tank designed for up to 0.5 psig (about 3.4 kPa) is an atmospheric tank, one designed for more than 0.5 and up to 15 psig is a low-pressure tank, and one designed for more than 15 psig (about 103 kPa) is a pressure vessel 2. The American Society of Mechanical Engineers (ASME) uses the same 15 psig line for its Section VIII, Division 1, which applies to fired and unfired vessels 5.
In a process plant the term covers drums, columns, reactors, heat exchanger shells, deaerators and spheres, not only storage 3,8,12. Fired boilers, piping, relief valves and transportable containers fall outside OSHA's pressure vessel guidelines and have their own rules 3. The concern is stored energy: OSHA notes that a damaged vessel can leak and cause poisoning, fire or explosion, and that a rupture can be far worse 1.
Where are pressure vessels used in oil, gas and chemical plants?
| Vessel type | What it does | Where it appears |
|---|---|---|
| Knockout drum or separator | Separates liquid from gas or vapor | Fuel gas systems, relief and flare systems |
| Column (tower) | Holds trays or packing for distillation or treating | Crude distillation, amine treating |
| Reactor | Holds feed and catalyst at reaction temperature and pressure | Hydrotreating |
| Heat exchanger shell | Contains the fluid on the outside of a tube bundle | Crude preheat trains, reboilers |
| Deaerator | Removes dissolved oxygen and carbon dioxide from boiler feedwater | Steam systems |
| Sphere | Stores liquefied gas under pressure | Liquefied petroleum gas (LPG), ammonia |
Sources: OSHA Technical Manual, Section IV, Chapters 2 and 3 12,3; NIST SP 780, 1990, which notes that ammonia and LPG storage vessels are usually spherical 4; API catalog entry for API Recommended Practice (RP) 572, which lists towers, exchangers, reactors and spheres among vessel types, 2025 8.
Which codes and rules apply to pressure vessels?
Each stage of a vessel's life has its own document. ASME Section VIII governs a new vessel from design and fabrication through inspection and testing to certification 5. A 1990 NIST assessment for OSHA noted that Section VIII has no in-service inspection rules and no legal force until a jurisdiction adopts it, as most US states, many cities and all Canadian provinces had done in whole or in part 4.
The National Board of Boiler and Pressure Vessel Inspectors, founded in 1919, brings together the chief inspectors of most US states and Canadian provinces and many large US cities 6. It registers code-built vessels and publishes the National Board Inspection Code (NBIC) for installation, inspection, repair and alteration, which most US and Canadian jurisdictions adopt into law 6.
Local programs set the detail. California's Cal/OSHA Pressure Vessel Unit, for example, issues permits to operate under the Title 8 Unfired Pressure Vessel Safety Orders, sections 450 to 560 7. After a 2017 steam vessel explosion in St. Louis, Missouri, killed four people, the US Chemical Safety and Hazard Investigation Board (CSB) recommended in 2022 that the city adopt a national in-service inspection standard such as NBIC Part 2 11.
| Stage of life | Document | What it covers |
|---|---|---|
| Design and construction | ASME BPVC Section VIII (Division 1, 2025 edition) | Requirements for a new vessel, from design to certification 5 |
| Overpressure protection | ASME BPVC Section XIII (2025 edition) | Rules for the relief devices that protect pressurized equipment 13 |
| Legal adoption | State and city boiler and pressure vessel laws | Which vessels need permits, registration and inspection 4,7 |
| In-service inspection and repair | API 510; National Board Inspection Code | Inspection, repair, alteration and rerating after start-up 6,8 |
| Process safety | OSHA 29 CFR 1910.119(j) | Mechanical integrity program for vessels in covered processes 9 |
API 510 also covers the pressure-relieving devices that protect a vessel 8. In processes covered by OSHA's process safety management (PSM) standard, inspection and testing must follow recognized and generally accepted good engineering practices 9.
How are pressure vessels inspected in service?
OSHA's guidelines describe five common nondestructive methods 3. Visual testing checks general condition; liquid penetrant testing finds surface-breaking flaws, including in austenitic stainless steels; magnetic particle testing finds surface and near-surface flaws, but only in ferromagnetic steels. Radiography finds internal flaws but can miss tight cracks, and ultrasonic testing finds internal flaws and measures wall thickness.
The same guidelines stress that a safety judgment depends on the largest flaw an inspection could miss, not the smallest one it can find, and that combining methods and repeating tests independently improves reliability 3.
OSHA's 2017 review of its refinery PSM emphasis program found recurring gaps in vessel inspection: thickness measurement locations not defined, vessels with no ultrasonic thickness readings, corrosion rates not calculated, and insulated equipment never checked for corrosion under insulation 10. Pressure vessels were among the equipment most often cited for deficient inspection procedures 10.
Where integrity problems show up
| Vessel or service | Typical integrity issue | In the Library |
|---|---|---|
| Amine treating vessels | Cracking in or next to welds, mostly welds that were not post-weld heat treated | What is amine corrosion and amine cracking? |
| Vessels in wet hydrogen sulfide service, including LPG spheres | Hydrogen-related cracking and blistering, mainly in weld heat-affected zones | What is wet hydrogen sulfide (H2S) damage? |
| Ammonia storage spheres | Stress corrosion cracking in or near welds; water and oxygen content strongly affect it | What is stress corrosion cracking (SCC)? |
| Deaerators | Corrosion fatigue cracking at welds that were not post-weld heat treated | What is corrosion fatigue? |
| Vessels in hot caustic service | Caustic stress corrosion cracking at welds (OSHA's example is pulp digesters) | What is caustic stress corrosion cracking? |
| Insulated vessels | Corrosion hidden under insulation that some refineries did not inspect for | What is corrosion under insulation (CUI)? |
Sources: OSHA Technical Manual, Section IV, Chapter 3 3; NIST SP 780, 1990 4; OSHA 3918, 2017 10. In the surveys summarized by NIST in 1990, about 40% of 294 amine plants and 31% of 189 wet hydrogen sulfide vessels reported cracking 4.
Common questions
- Is a storage tank a pressure vessel?
- Only if it is designed for more than 15 psig. OSHA classes tanks designed for up to 0.5 psig as atmospheric and those from above 0.5 to 15 psig as low-pressure tanks; both are usually called storage tanks rather than pressure vessels. See [What are the main types of storage tanks?](/library/storage-tank-types/).
- Does ASME Section VIII cover inspection after start-up?
- No. Section VIII covers a vessel up to its certification as new, and in-service inspection, repair and alteration fall under API 510 or the NBIC, as adopted by the jurisdiction.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Pressure Vessels (Safety and Health Topics) · US Occupational Safety and Health Administration (OSHA)
- 2.29 CFR 1910.106, Flammable liquids (in 29 CFR Part 1910, Subpart H) · eCFR, US Office of the Federal Register
- 3.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
- 4.NIST Special Publication 780, Guidelines for Pressure Vessel Safety Assessment (S. Yukawa) · US National Institute of Standards and Technology (NIST)
- 5.BPVC.VIII.1, BPVC Section VIII, Rules for Construction of Pressure Vessels, Division 1 (product page) (2025) · American Society of Mechanical Engineers (ASME)
- 6.About the National Board · National Board of Boiler and Pressure Vessel Inspectors
- 7.Pressure Vessels (Cal/OSHA Pressure Vessel Unit) · California Department of Industrial Relations
- 8.2025 Publications Catalog (Refining: Inspection of Refinery Equipment) · American Petroleum Institute (API)
- 9.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
- 10.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
- 11.Loy Lange Box Company Pressure Vessel Explosion (investigation page) · US Chemical Safety and Hazard Investigation Board (CSB)
- 12.OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes · US Occupational Safety and Health Administration (OSHA)
- 13.BPVC.XIII, BPVC Section XIII, Rules for Overpressure Protection (product page) (2025) · American Society of Mechanical Engineers (ASME)