Skip to content
Beaconby Winda
FactInspection, Testing and Monitoring · In-service inspection codes

What is API 572 (inspection practices for pressure vessels)?

·10 sources

Short answer

API 572 is the American Petroleum Institute's recommended practice (RP) on how in-service pressure vessels, such as towers and exchangers, are inspected. It supplements the API 510 inspection code with guidance on planning, methods, repairs and records. The current edition is the 5th, published in November 2023.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

After a pressure vessel in amine service failed in 1984, an industry survey found cracking at about 40% of 294 amine plants, in absorbers, regenerators, heat exchangers and piping 1. Every crack was in or near a weld, mostly welds that had not been stress relieved, and internal examination by wet fluorescent magnetic particle testing was the preferred way to find them 1. The same chapter reports weld-zone cracking from wet hydrogen sulfide in storage spheres for liquefied petroleum gas (LPG) 1. Whether such damage is found depends on inspection practice: which vessels are opened, which surfaces are prepared and which method is used.

What does API 572 cover?

API presents RP 572 as a companion to API 510 that gives vessel inspectors background on inspection practice to build their skills 2. It deals with the vessel types found in hydrocarbon and chemical processing, including towers, shell-and-tube and air-cooled heat exchangers, reactors and spheres 2. Its subjects are vessel components, inspection planning, inspection intervals, methods of inspection and assessment, repair methods, and records and reports 2. API announced the 5th edition 4, which runs to 163 pages 2 and is the edition listed for API 510 inspector exams from September 2026 3.

DocumentTypeRole for in-service vessels
API 510, 11th edition (October 2022)CodeRequirements for in-service inspection, repair, alteration and rerating 2,3
API RP 572, 5th edition (November 2023)Recommended practiceHow inspection is planned and carried out, and how it is recorded 2
API RP 571, 3rd edition (March 2020)Recommended practiceBackground on more than 60 damage mechanisms in refinery equipment 2
API RP 576, 5th edition (September 2024)Recommended practiceInspection of pressure-relieving devices 3
National Board Inspection Code (NBIC), 2025 editionJurisdictional standardInstallation, inspection, repair and alteration rules adopted into law by most US and Canadian jurisdictions 5
29 CFR 1910.119(j)US regulationInspection and testing that follows good engineering practice, at a justified frequency, with records 6

How are vessels inspected in practice?

An examination can be done with the vessel stripped down and out of service, or with it running under normal conditions, and some equipment needs both 10.

The technical manual of the US Occupational Safety and Health Administration (OSHA) lists five methods in wide use on vessels: visual examination, liquid penetrant, magnetic particle, radiography and ultrasonic testing 1. The first three find only flaws at or near the surface, while radiography and ultrasonic testing reach into the wall 1. Based on service experience, the manual directs most attention to:

  • vessels in deaerator, amine, wet hydrogen sulfide, ammonia and pulp digester service; 1
  • welds and the metal next to them; 1
  • vessels whose fabrication welds were never post-weld heat treated; 1
  • repaired vessels, above all those not heat treated after repair 1.

The same manual lists the records that support a safety assessment: vessel identity and data report, design code, pressures, temperatures, materials, corrosion allowance and heat treatment, operating history and changes, and each inspection's type, extent, date, methods, personnel qualifications, results and follow-up 1.

How does API 572 relate to API 510 and the law?

API 510 is the code that sets requirements; RP 572 is a recommended practice that explains how inspection is done 2. The US process safety rule requires inspection and testing of pressure vessels to meet recognized and generally accepted good engineering practice (RAGAGEP), at frequencies backed by that practice and operating experience, and to be documented 6. OSHA's 2017 review of its refinery inspections notes that the rule lets employers select their RAGAGEP and names API publications as examples for vessel and piping inspection 7. Some states write API 510 into their rules: Virginia lets approved owner-user inspection agencies inspect petroleum and chemical vessels to it 8.

Where integrity problems show up

What it finds wellWhat it can miss or get wrongIn the Library
Internal magnetic particle testing of weld surfaces finds cracking in amine and wet hydrogen sulfide service 1Needs entry and a clean surface; works only on ferromagnetic steels and is most sensitive to cracks lying across the magnetic field 1What is amine corrosion and amine cracking? · What is wet hydrogen sulfide (H2S) damage?
Ultrasonic thickness readings measure general wall loss from one side 1Readings exist only where they are planned; OSHA's refinery inspections cited procedures that did not fix the number and location of thickness points, and corrosion rates above the expected rate that were not acted on 7How does ultrasonic thickness measurement work?
Inspection aimed at expected damageEarly high temperature hydrogen attack is hard to detect; at Anacortes in 2010 the ruptured exchangers had never been inspected for it, because damage reviews used design data instead of measured conditions 9What is high temperature hydrogen attack (HTHA)?
External visual inspection of shells, nozzles and supports 1Corrosion under insulation: OSHA cited a refinery for not inspecting for it on vessels and piping in a sulfur unit 7What is corrosion under insulation (CUI)?

Sources: OSHA Technical Manual 1; OSHA 3918, 2017 7; US Chemical Safety and Hazard Investigation Board (CSB) report on the 2010 Anacortes refinery explosion, 2014 9.

Common questions

Is API 572 mandatory?
Not in itself. It is a recommended practice that becomes binding where a regulator, a contract or an owner's procedures adopt it; under US process safety rules employers select their good engineering practice, and OSHA cites API publications as examples.
What is the difference between API 510 and API 572?
API 510 is the inspection code with requirements for in-service vessels, while RP 572 describes inspection practice in support of it. Inspectors certified to API 510 are examined on both, among other documents.
Does API 572 cover fired heaters, boilers or storage tanks?
No. API publishes RP 573 for fired boilers and process heaters and RP 575 for atmospheric and low-pressure storage tanks.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
  2. 2.2025 Publications Catalog (entries for API 510, RP 571, RP 572, RP 573, RP 575) (RP 572, 5th edition, November 2023) · American Petroleum Institute (API)
  3. 3.API 510 Exam Publications Effectivity Sheet for September 2026, January 2027 and May 2027 (RP 572, 5th edition, November 2023; RP 576, 5th edition, September 2024) · American Petroleum Institute (API)
  4. 5.National Board Inspection Code (NBIC) · The National Board of Boiler and Pressure Vessel Inspectors (NBBI)
  5. 6.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
  6. 7.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
  7. 8.16VAC25-50, Boiler and Pressure Vessel Regulations (16VAC25-50-120) · Virginia Administrative Code, Virginia General Assembly
  8. 9.Investigation Report: Catastrophic Rupture of Heat Exchanger (Seven Fatalities), Tesoro Anacortes Refinery, Report No. 2010-08-I-WA · US Chemical Safety and Hazard Investigation Board (CSB)
  9. 10.Safety of pressure systems: Pressure Systems Safety Regulations 2000, Approved Code of Practice and guidance (L122, second edition) · UK Health and Safety Executive (HSE)