What are corrosion-resistant alloys (CRAs)?
Corrosion-resistant alloys (CRAs) are stainless steels, nickel-based alloys and similar metals that resist corrosion in fluids that attack carbon steel. In oil and gas they include 13% chromium martensitic, duplex and austenitic stainless steels and nickel alloys, used solid or as a cladding or lining inside steel pipe. ISO 15156-3 covers their use in H2S service.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
Corrosion-resistant does not mean crack-proof: the Specialty Steel Industry of North America (SSINA) states that no stainless steel grade is completely immune to chloride stress corrosion cracking, and the UK Health and Safety Executive (HSE) reports that austenitic stainless steel in chloride solutions accounts for the most frequent stress corrosion cracking failures in piping 2,7. CRAs are chosen where carbon steel would corrode too fast, and both their resistance and their cost rise with alloy content 4,8. Choosing one replaces general thinning with a different set of damage mechanisms, set out below.
What makes an alloy corrosion-resistant?
Most CRAs rely on chromium. Once steel holds at least 10.5% chromium, a thin, adherent surface film forms that stops the iron underneath from oxidizing; this is the basis of the ASTM A941 definition of stainless steel cited by SSINA 1. Other elements add specific resistance 1:
- Nickel gives the austenitic structure, with good toughness down to cryogenic temperatures and better resistance to acids. 1
- Molybdenum improves resistance to pitting, crevice corrosion and chlorides. 1
- Nitrogen makes austenitic and duplex grades stronger and more resistant to corrosion. 1
The film needs enough chromium everywhere. If chromium carbides form along grain boundaries, for example in a weld heat-affected zone, local chromium can fall below 10.5% and the metal there corrodes between grains 1.
Which CRA families are used in oil and gas?
| Family | Key features | Typical oil and gas use |
|---|---|---|
| Martensitic stainless (13% chromium and modified "super" 13% chromium) | Hardenable by heat treatment; magnetic 3 | Well tubulars and line pipe; API TR 13TR1 studies how modified 13% chromium grades crack in halide brines once acidic gas from production reaches them 6 |
| Austenitic stainless (304, 316, 6% molybdenum grades) | Non-magnetic when annealed; tough at low temperature; 304 and 316 are the most used stainless steels 1,3 | Process piping, where chloride cracking is the most frequent stress corrosion failure; liquid oxygen and other cold duty 7 |
| Nickel-based alloys | Highest nickel, chromium and molybdenum content, at the top of the resistance and cost range 4 | Precipitation-hardened and solid-solution nickel alloys are among the CRA families used in oil and gas production 5 |
| Clad or lined pipe | A CRA layer on the inside of carbon steel pipe 6 | Line pipe carrying oil, gas and water 6 |
Sources: SSINA 1,3; AMPP paper 09381 4; OSTI record of the NACE paper collection on CRAs in oil and gas production 5; API 2025 catalog 6; HSE 7.
Where are CRAs used instead of carbon steel?
The usual approach in process plants is a material that corrodes slowly plus a thickness allowance, because fully resistant materials are often too costly 7. A 1990 NIST assessment noted that severe general corrosion calls for stainless steels or other corrosion-resistant materials 8. In practice CRAs appear in four places:
- Wells. API Spec 5CRA/ISO 13680 (2nd edition, October 2022) covers seamless CRA casing, tubing and coupling stock, with a higher product level for material meant to resist cracking under the ISO 15156 series 6.
- Pipelines and flowlines. API Spec 5LC covers solid CRA line pipe in austenitic, martensitic, duplex and nickel-based grades, and Spec 5LD covers clad or lined pipe 6.
- Refineries. In hot sulfur service, the US Chemical Safety Board (CSB) calculated that carbon steel corrodes about 120 times faster than 18% chromium stainless steel at 630 °F (about 332 °C) 10. API TR 938-C covers duplex grades used in refineries 6.
- Sour service. Part 3 of NACE MR0175/ISO 15156 covers cracking-resistant CRAs and other alloys 9.
What are the limits of CRAs?
- Chloride stress corrosion cracking. Austenitic grades are the most susceptible, with 304 and 316 very susceptible; ferritic grades resist well and duplex grades fall between 2. Fully immersed cracking is rare below 60 °C (150 °F), but evaporation can concentrate chlorides and cause cracking at lower temperatures 2.
- Cracking in sour service. Not every CRA is acceptable in H2S; Part 3 of ISO 15156 deals with this 9.
How are CRAs checked during construction?
Composition is checked with positive material identification (PMI); the CSB notes that portable instruments readily measure chromium in the field 10, and API RP 578 (4th edition, 2023) covers material verification programs 6. Inspection methods also change: magnetic particle testing needs a ferromagnetic material, so liquid penetrant testing is used on austenitic stainless steels 11.
Where integrity problems show up
| Decision or step at this stage | What it affects later | In the Library |
|---|---|---|
| Choosing a 304 or 316 grade for warm chloride-bearing service | Chloride stress corrosion cracking, possible below 60 °C where chlorides concentrate by evaporation 2,7 | What is chloride stress corrosion cracking? |
| Welding or heat treating austenitic stainless so carbides form | Chromium-depleted zones that corrode between grains 1 | What is intergranular corrosion? |
| Buying CRA tubulars for a sour well without cracking requirements | API 5CRA's higher product level exists for cracking-resistant material 6 | Sulfide stress cracking |
| Skipping PMI on alloy parts | A lower alloy installed where a CRA was specified 6,10 | What is positive material identification (PMI)? |
Common questions
- Is stainless steel a corrosion-resistant alloy?
- Yes. Stainless steels make up most of the CRA range, which an AMPP paper describes as running from ferritic stainless steels to nickel-based and titanium alloys.
- What is the difference between solid and clad CRA pipe?
- Solid CRA pipe is alloy through the wall (API Spec 5LC); clad or lined pipe has a carbon steel outer wall with a CRA layer inside (API Spec 5LD).
- Are CRAs immune to corrosion?
- No. They resist general corrosion well but can suffer pitting, crevice corrosion and stress corrosion cracking in the wrong environment.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Alloying Elements · Specialty Steel Industry of North America (SSINA)
- 2.Chloride Stress Corrosion Cracking · Specialty Steel Industry of North America (SSINA)
- 3.Alloy Families · Specialty Steel Industry of North America (SSINA)
- 4.Defining Acceptable Environmental Ranges and Welding Procedures for Corrosion Resistant Alloys (paper 09381, store page with abstract) · Association for Materials Protection and Performance (AMPP)
- 5.Corrosion-resistant alloys in oil and gas production (OSTI record 378117) · US Department of Energy, Office of Scientific and Technical Information (OSTI)
- 6.2025 Publications Catalog (entries for Spec 5CRA/ISO 13680:2020, Spec 5LC, Spec 5LD, TR 13TR1, TR 938-C, RP 578) · American Petroleum Institute (API)
- 7.Corrosion / selection of materials (COMAH technical measures) · UK Health and Safety Executive (HSE)
- 8.NIST Special Publication 780, Guidelines for Pressure Vessel Safety Assessment (S. Yukawa) · US National Institute of Standards and Technology (NIST)
- 9.NACE MR0175/ISO 15156, Part 3 (part titles and document history) · GlobalSpec Engineering360 standards catalog
- 10.Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 11.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)