What is stress corrosion cracking in pipelines (high-pH and near-neutral pH)?
Pipeline stress corrosion cracking (SCC) is cracking on the outside of buried steel pipe where susceptible steel, tensile stress and corrosive water meet. High-pH SCC runs between steel grains in concentrated carbonate-bicarbonate solution; near-neutral pH SCC runs across grains in dilute groundwater. US gas rules cover its direct assessment in 49 CFR 192.929.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
On 12 September 2009 a 914 mm natural gas pipeline near Englehart, Ontario, ruptured, exploded and burned; the Transportation Safety Board of Canada (TSB) traced the failure to near-neutral pH SCC at the toe of the long seam weld 3. The line was inspected regularly with in-line tools, but the TSB found the magnetic flux leakage (MFL) tool in use was not designed to identify SCC in the seam weld 3. A Canadian national inquiry had counted 22 SCC failures in Canada from 1977 to 1996, 12 of them ruptures 1.
What conditions cause SCC on a pipeline?
Canada's National Energy Board (NEB) and the US Office of Pipeline Safety both describe three conditions that act together, none sufficient alone: a susceptible pipe steel, a tensile stress and a potent environment at the pipe surface 1,2. The NEB found every commonly used line pipe steel susceptible, named operating pressure as the main source of stress, and noted that research had not found a stress below which cracks will not start and grow 1.
The environment only reaches the steel when the coating and the cathodic protection (CP) both fail at the same spot 1. Polyethylene tape is the classic case: it can disbond or tent, and because it insulates, it keeps CP current away from the steel underneath 1,2. Most Canadian SCC failures came after 1985, on tape-coated lines built from 1968 to 1973 1. Fusion-bonded epoxy (FBE) coatings have performed well, provided field joints are coated equally well 1.
Cracks form in colonies of closely spaced, parallel cracks on the outer surface, usually too small to see at first. Over years they lengthen, deepen and link up until the pipe leaks or ruptures 1.
How do high-pH and near-neutral pH SCC differ?
| Feature | High-pH SCC | Near-neutral pH SCC |
|---|---|---|
| Water at the crack | Concentrated carbonate-bicarbonate, formed when CP raises pH under disbonded coating 2 | Dilute groundwater with dissolved carbon dioxide (CO2) 1,2 |
| pH | Above about 9 1 | About 5.5 to 7.5 1,2 |
| Cathodic protection at the site | Present, in a narrow potential range 1 | Shielded; CP does not reach the steel 1 |
| Temperature link | Strong; growth slows sharply in cooler pipe, so it clusters within about 20 km downstream of compressor stations 1,2 | No clear link to pipe temperature; more common in colder climates 1 |
| Crack path | Between grains (intergranular), narrow and tight 1,2 | Across grains (transgranular), wider, with corroded walls 1,2 |
| First recognized | First documented SCC pipeline failure, Natchitoches, Louisiana, mid-1960s 2 | Canadian failures of 1985 and 1986, first called "low pH" SCC 1,2 |
Research on high-pH SCC is the older body of work, and the NEB noted that findings for one type do not carry over to the other 1. For near-neutral pH cracking, corrosion inside the crack and hydrogen entering the steel are both thought to play a part 1.
How is pipeline SCC found?
- Crack-detecting in-line inspection (ILI). The Pipeline and Hazardous Materials Safety Administration (PHMSA) study lists ultrasonic and electromagnetic acoustic transducer (EMAT) tools among SCC methods 2. EMAT tools are built to detect and size axial cracks; MFL tools find metal loss but have limited ability to find SCC, especially at a seam weld 3.
- Hydrostatic testing. The NEB named hydrostatic retesting as one of the two main ways to detect SCC 1; the Englehart section had been retested five times since 1986 3.
- Investigative digs. The NEB described excavations chosen by susceptibility models 1; at a dig, cracks are checked with methods such as magnetic particle inspection 2.
- SCC direct assessment (SCCDA). Under 49 CFR 192.929, an SCCDA plan follows NACE SP0204 through four steps and includes at least two above-ground surveys and at least three direct examinations at the most likely sites 4. The rule calls SCCDA "complementary with other inspection methods for SCC" such as ILI or spike hydrostatic testing 4.
How is pipeline SCC managed?
The NEB's main recommendation was a company-specific SCC management program: identify where SCC may be, find it, and deal with it 1. It also recommended that new pipelines be designed so that in-line inspection tools can pass 1. A general pressure reduction was judged ineffective because no threshold stress is known, though it can serve as a temporary measure where failure is imminent 1.
Repair options under 49 CFR 192.929 include removing the cracked pipe, a Type B sleeve, a spike pressure test, or grinding followed by non-destructive testing and a remaining strength check 4. API RP 1176 (1st edition, 2016) covers the assessment and management of cracking in gas and liquid pipelines 5.
Where integrity problems show up
| Where it occurs (unit or equipment) | Conditions that drive it | How it is usually found | In the Library |
|---|---|---|---|
| Gas pipe within about 20 km downstream of compressor stations | Warm gas, disbonded coating, carbonate-bicarbonate at the steel (high-pH) 1,2 | Crack ILI tools and hydrostatic testing 2 | What types of in-line inspection tools are there (MFL, UT, EMAT, geometry)? |
| Polyethylene tape-coated pipe laid in the 1960s and 1970s | Tape disbonds and shields CP from the steel 1,2 | Investigative digs with magnetic particle inspection 1,2 | How does cathodic protection work? |
| Long seam weld toe under tented tape | Groundwater under the tent; normal pressure cycles grow cracks 3 | EMAT ILI or hydrostatic retest; MFL tools are not suited 3 | Magnetic flux leakage |
| Segments with wet-dry soils and soils that damage coatings | Terrain and soil conditions named by the NEB 1 | Susceptibility models pick dig sites 1 | What is direct assessment (ECDA, ICDA, SCCDA)? |
| US gas segments under integrity management | Carbonate-bicarbonate, cyclic loading, CP swings and shielding coatings, all named in the rule 4 | SCCDA surveys and direct examinations 4 | What is pipeline integrity management? |
| Hazardous liquid pipelines | Three US liquid line failures were attributed to SCC in 2003 2 | Crack assessment under API RP 1176 5 | What is API 1160 (integrity management for hazardous liquid pipelines)? |
Sources: NEB MH-2-95, 1996 1; PHMSA SCC Study, 2005 2; TSB P09H0074, 2010 3; 49 CFR 192.929 4; API 2025 catalog 5.
Common questions
- Is high-pH SCC the same as carbonate cracking in refineries?
- They share carbonate chemistry but occur in different places. High-pH pipeline SCC grows on the outside of buried pipe under disbonded coating; refinery carbonate cracking grows inside equipment that holds alkaline sour water, such as fluid catalytic cracking overheads.
- Does lowering the operating pressure stop SCC?
- Not by itself. The NEB found no pressure below which SCC will not start and grow, so it treated pressure reduction as a temporary measure combined with others.
- Can a magnetic flux leakage pig find SCC?
- Not reliably. The TSB found MFL tools suited to metal loss but not to SCC on the outer surface, particularly at the long seam.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Public Inquiry Concerning Stress Corrosion Cracking on Canadian Oil and Gas Pipelines, Report of the Inquiry (MH-2-95) · National Energy Board (now Canada Energy Regulator)
- 2.TTO Number 8, Stress Corrosion Cracking Study, Final Report (prepared by Michael Baker Jr., Inc.) · US Department of Transportation, Office of Pipeline Safety (now PHMSA)
- 3.Pipeline Investigation Report P09H0074: natural gas pipeline rupture near Englehart, Ontario, 12 September 2009 · Transportation Safety Board of Canada (TSB) ·
- 4.49 CFR 192.929, What are the requirements for using Direct Assessment for Stress Corrosion Cracking (SCCDA)? · eCFR, US Office of the Federal Register
- 5.2025 Publications Catalog (entry for RP 1176) (RP 1176, 1st edition, 2016 (includes Errata 1, February 2021)) · American Petroleum Institute (API)
- 6.Question 3: Carbonate stress corrosion cracking (CSCC) in FCC main fractionator overhead systems (technical Q&A database) · American Fuel & Petrochemical Manufacturers (AFPM)