What is atmospheric corrosion?
Atmospheric corrosion is corrosion of metal exposed to air, driven by thin films of moisture from rain, dew or humidity on the surface. Salt and pollutants in those films make it faster, so marine and industrial sites suffer most. US pipeline rules (49 CFR 192.479 and 192.481, 195.583) require exposed pipe to be coated and periodically inspected.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
In January 2025 the US Bureau of Safety and Environmental Enforcement (BSEE) reported an explosion on an offshore platform when a flange on an 8-inch gas pipeline failed; the fire spread about 80 feet to the bottom of the production deck 1. BSEE found severe corrosion on the outside of the flange, driven by high chlorine levels (12,000 parts per million) with oxygen present, and noted that the flange had been painted but the coating had not been properly maintained 1. Wall loss weakened the flange until it failed in a brittle, circumferential break 1.
What makes atmospheric corrosion faster?
Metal in air corrodes only while a film of water sits on it 6, so anything that keeps the surface wet or makes that water more conductive speeds the attack:
- Time of wetness. At NASA's beachside test site in Florida, carbon steel corrodes fastest in winter: morning condensation lingers at lower temperatures, while summer heat dries surfaces quickly 2,4.
- Salt. Marine aerosols deposit chloride on the surface; at the NASA site, higher waves offshore went with higher chloride deposition 2.
- Pollution. Combustion products, fertilizers and road salt raise the conductivity of rain and condensation, so even a nominally clean atmosphere can become aggressive 6.
- Trapped water. Corrosion concentrates where rain or condensation cannot run off: joints, hollow sections, supports and dirt deposits 6,7.
- Climate. NPL ranks severity as low in dry regions, moderate in temperate and open rural areas, and highest in humid tropical and marine locations and polluted industrial air 6.
How fast can steel corrode in marine air?
NASA's Kennedy Space Center has run its beachside site, about 150 feet from the Atlantic high tide line, since the 1960s, and documents it as having higher atmospheric corrosion rates than other known US test sites 3,4.
| Measurement at NASA's beachside site | Value |
|---|---|
| Carbon steel (1010) corrosion rate, one-year exposures | 0.127 to 0.51 mm/y (5 to 20 mils per year, mpy) 2 |
| Weighted average rate | 0.28 mm/y (11 mpy) 2 |
| Chloride deposition (wet candle method) | 70 to 7,300 mg/m2 per day, weighted mean 983 2 |
| Sulfur dioxide deposition, 2002 to 2010 | 0.92 to 1.81 mg/m2 per day, a very low level 2 |
Short tests can mislead. When NASA extrapolated one-month exposures to a yearly rate, the result matched the measured one-year rate only about half the time, so it stopped using monthly data to predict yearly rates 2.
Sources: NASA KSC Atmospheric Site Data 2.
How is atmospheric corrosion found?
- Periodic inspection. US rules require exposed gas pipeline to be inspected at least once every 3 calendar years onshore (intervals up to 39 months) and every calendar year offshore (up to 15 months); hazardous liquid lines follow the same onshore and offshore intervals 5.
- Attention to known hot spots. Those inspections must look closely at soil-to-air interfaces, pipe under thermal insulation or disbonded coating, pipe supports, splash zones, deck penetrations and spans over water 5.
- Wall thickness checks. After the 2025 flange failure, BSEE recommended non-destructive wall thickness measurement along gas pipelines and inspections that assess corrosion against the design and repair history 1.
- Site corrosivity. Exposed steel coupons and chloride collectors characterize how aggressive a site is; NASA rates its beachside chloride level as high under ISO 9223 criteria 2.
How is atmospheric corrosion controlled?
- Coatings. US rules require pipeline exposed to the atmosphere to be cleaned and coated with a suitable coating, except where tests or experience show only light surface oxide will form or safety will not be affected before the next inspection; that exception does not cover offshore splash zones or soil-to-air interfaces 5.
- Coating maintenance. BSEE's 2025 case turned on a coating that had not been kept up 1. Corrosion can also spread under a coating from small defects, and zinc-rich coatings are noted for the cathodic protection they give carbon steel 7.
- Design for drainage, so that water does not collect at joints and in hollow sections 6.
Where integrity problems show up
| Where it occurs (unit or equipment) | Conditions that drive it | How it is usually found | In the Library |
|---|---|---|---|
| Offshore topsides piping and flanges | Chloride and oxygen; coating not maintained 1 | Non-destructive wall thickness measurement and corrosion assessment during inspections 1 | How does ultrasonic thickness measurement work? |
| Pipe supports, deck penetrations, splash zones and spans over water | Water and salt held against the steel 5,6 | Close attention during periodic inspection, every year offshore 5 | What should an inspection plan contain? |
| Soil-to-air interfaces on pipelines | Named by US rules; no exemption from coating 5 | Close attention during inspection at least every 3 years onshore 5 | What is soil corrosion? |
| Coastal plants, terminals and test racks | Marine chloride and long wet periods in cooler months 2,4 | Exposed steel coupons and chloride deposition measurements 2 | What is corrosion monitoring and which methods are used? |
| Pipe under thermal insulation or disbonded coating | Trapped water 5 | Close attention during atmospheric corrosion inspection 5 | What is corrosion under insulation (CUI)? |
Sources: BSEE Safety Alert 493, 2025 1; NASA KSC 2,4; 49 CFR 192.479, 192.481 and 195.583 5; NPL Guide No. 5, 2021 6.
Common questions
- Is atmospheric corrosion the same as corrosion under insulation?
- No. Atmospheric corrosion acts on surfaces open to the air; corrosion under insulation happens where insulation traps water against the metal. US pipeline rules cover both in the same inspection and list pipe under thermal insulation as a place needing close attention.
- Is general rusting serious?
- Uniform rusting is the most common form of corrosion, and NASA notes it usually attracts maintenance long before a structure is weakened. Local wall loss at flanges, supports and joints is different: the 2025 offshore failure began as external corrosion under a neglected coating.
- Can a one-month coupon give the yearly corrosion rate?
- Not reliably. At NASA's marine site, monthly results scaled up to a year agreed with measured yearly rates only about half the time.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Safety Alert No. 493, BSEE Investigation Determines Corrosion Caused Pipeline Explosion · US Bureau of Safety and Environmental Enforcement (BSEE) ·
- 2.Atmospheric Site Data · NASA Kennedy Space Center, Corrosion Engineering Laboratory
- 3.Corrosion (Corrosion Engineering Laboratory home page) · NASA Kennedy Space Center
- 4.Atmospheric Exposure · NASA Kennedy Space Center, Corrosion Engineering Laboratory
- 5.49 CFR 192.479 and 192.481, Atmospheric corrosion control (and 49 CFR 195.583) · eCFR, US Office of the Federal Register
- 6.Bimetallic Corrosion (Guides to Good Practice in Corrosion Control No. 5) · UK National Physical Laboratory (NPL)
- 7.Forms of Corrosion · NASA Kennedy Space Center, Corrosion Engineering Laboratory