Skip to content
Beaconby Winda
FactRegulation, Standards and Compliance · Audit and evidence

What inspection records do codes require you to keep?

·18 sources

Short answer

Codes and regulations require inspection records showing what was inspected, when, by whom, how and with what result, and set how long they are kept. In the US, 29 CFR 1910.119(j)(4)(iv) sets that content for process plant equipment, while 49 CFR 192 and 195 set pipeline records, many kept for the pipeline's life.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

A folder of inspection reports is not the whole record the rules expect. Under the US gas transmission integrity management rules, operators must keep, for the pipeline's useful life, the documents behind every identification, calculation, justification, deviation and decision in the program, ready for review during an inspection 7. Records also carry the numbers that integrity decisions rest on: a corrosion rate is metal loss over time, so it needs dated readings from the same location (see Corrosion rate). In its refinery inspections, the US Occupational Safety and Health Administration (OSHA) cited inadequately recorded piping inspections and rising thickness readings that nobody investigated 16.

What must an inspection record contain?

RecordContent the rule namesRule
Process equipment inspection or testDate; who performed it; serial number or other equipment identifier; what was done; results29 CFR 1910.119(j)(4)(iv) 1; 40 CFR 68.73(d)(4) 2
Gas pipeline strength testOperator, responsible employee and test company; test medium, pressure and duration; pressure charts or readings; significant elevation changes; leaks and failures and how they were handled49 CFR 192.517(a) 5
Liquid pipeline pressure testCharts and instrument calibration data; names; date and time; minimum test pressure; medium; facility and apparatus; any pressure discontinuities explained; an elevation profile where differences exceed 100 ft (30 m); temperature49 CFR 195.310(b) 9
Alberta pipeline pressure testA legible chart that runs unbroken through the whole test and shows when it began and ended (date and time), an unbroken record of pipe temperature, the location, and licence and segment numbersPipeline Rules, AR 125/2023, s. 36 14
Corrosion control test or surveyEnough detail to show that protection is adequate or that no corrosive condition exists49 CFR 192.491(c) 4; 195.589(c) 11
Pipe repairDate, location and description49 CFR 192.709(a) 6; 195.404(c)(1) 10

How long must inspection records be kept?

RuleRecordMinimum retention
29 CFR 1910.119(j)(4)(iv) and (o)(5)Equipment inspections and tests; compliance audit reportsNo period stated for inspections; the two most recent audit reports 1
40 CFR 68.200Records supporting an EPA risk management program5 years, unless subpart D says otherwise 3
49 CFR 192.709Gas transmission pipe repairs; other repairs; patrols, surveys, inspections and testsLife of the pipe; 5 years; 5 years or until the next one, whichever is longer 6
49 CFR 192.517(a) and 192.947Strength tests; integrity management recordsUseful life of the pipeline 5,7
49 CFR 192.491 and 195.589Corrosion control tests, surveys and inspectionsAt least 5 years, some for as long as the line is in service 4,11
49 CFR 195.404(c)Liquid pipe repairs; other repairs; inspections and testsLife of the pipe; 1 year; 2 years or until the next one, whichever is longer 10
49 CFR 195.266 and 195.310Construction records; the latest pressure testLife of the facility; while the facility is in use 8,9
Canada, SOR/99-294 s. 56Audit and inspection records; construction records, mill certificates, surveillance reports, defect documentsLonger of 5 years or two audit cycles; until at least 2 years after abandonment 12
Alberta, AR 125/2023 s. 12 and 13Design-to-decommissioning recordsAs CSA Z662 requires, and passed to any buyer 14
UK, Pressure Systems Safety Regulations 2000, reg. 14Latest examination report, and earlier ones that help judge safety or repairsKept at the site and handed to any new owner or user 15

Sources: the rule cited in each row, all checked 25 October 2026 1,6,10,12,14,15.

What do inspection codes add?

Under the US process safety rule, the inspection codes an employer adopts, such as API 510 or API 570, serve as its RAGAGEP (recognized and generally accepted good engineering practice) 16. OSHA presumes a violation when an employer departs from a "shall" statement in the RAGAGEP it adopted 17, so mandatory record provisions in those codes carry weight in an inspection. In Canada, the federal regulations apply their own retention periods in addition to those in the CSA standards they adopt 12.

How do records feed integrity decisions?

The Canada Energy Regulator's guidance lists what pipeline integrity records should hold: original pipe data (material, maker, grade, seam and girth weld type, welder identification, non-destructive examination, heat numbers, weld maps), coatings, pressure tests, maximum operating pressure, in-line inspection data, cathodic protection surveys, and inspections of relief valves, emergency shutdown devices and other valves 13. OSHA's refinery guidance adds that an irregular result must be retested rather than ignored, and the cause resolved 16. Records also follow the asset: in Alberta, a buyer missing records must prove fitness for service by engineering assessment 14, and in the UK the previous owner must hand records over in writing 15.

Where integrity problems show up

RequirementWhat it means for integrity records or workIn the Library
1910.119(j)(4)(iv), five items per recordEach reading tied to an equipment identifier and date lets later readings at the same point give a rate 1What is mechanical integrity (MI)?
192.947(d), decision and deviation documentsIn a Canadian case at Prince George, British Columbia, in 2018, the TSB found no record of the rationale or approval for deferring a crack inspection before a rupture 7,18What is pipeline integrity management?
192.709(c) and 195.404(c)(3), keep until the next inspectionThe last record is the baseline for the next interval 6,10How are inspection intervals set for vessels, piping and tanks?
SOR/99-294 s. 56(g), mill certificatesMaterial records must outlast the pipeline by at least 2 years after abandonment 12What is a mill test certificate (EN 10204 3.1 and 3.2)?
AR 125/2023 s. 13, records on transferLost or incomplete records shift the burden to an engineering assessment 14What does a technical due diligence check in an asset acquisition?
OSHA refinery findings on anomalous dataIncreasing thickness readings went uninvestigated; data must be checked as it is recorded 16What is an inspection data management system (IDMS)?

Sources: eCFR 1,6,7,10; SOR/99-294 12; AR 125/2023 14; OSHA 3918, 2017 16; TSB report P18H0088, 2020 18.

Common questions

Does the PSM standard say how long to keep inspection records?
Its paragraph on inspection documentation sets content but no period. EPA's Risk Management Program rule keeps supporting records for 5 years unless its subpart D says otherwise. See What is process safety management (PSM)?
Is an inspection record the same as an inspection report?
No. A report is one record; the rules also call for supporting documents, such as the decision and deviation records required for US gas integrity programs.
Can inspection records be electronic?
Yes, under conditions. Alberta accepts electronic pressure-test charts if a permanent copy stays accessible to the regulator and the sampling rate, resolution and range are adequate; the UK rules allow records kept in a form that can be reproduced at the site.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
  2. 2.40 CFR 68.73, Mechanical integrity · eCFR, US Office of the Federal Register
  3. 3.40 CFR 68.200, Recordkeeping · eCFR, US Office of the Federal Register
  4. 4.49 CFR 192.491, Corrosion control records · eCFR, US Office of the Federal Register
  5. 5.49 CFR 192.517, Records (strength testing) · eCFR, US Office of the Federal Register
  6. 6.49 CFR 192.709, Transmission lines: Record keeping · eCFR, US Office of the Federal Register
  7. 7.49 CFR 192.947, What records must an operator keep? · eCFR, US Office of the Federal Register
  8. 8.49 CFR 195.266, Construction records · eCFR, US Office of the Federal Register
  9. 9.49 CFR 195.310, Records (pressure testing) · eCFR, US Office of the Federal Register
  10. 10.49 CFR 195.404, Maps and records · eCFR, US Office of the Federal Register
  11. 11.49 CFR 195.589, What corrosion control information do I have to maintain? · eCFR, US Office of the Federal Register
  12. 12.Canadian Energy Regulator Onshore Pipeline Regulations (SOR/99-294) · Justice Laws Website, Government of Canada
  13. 13.Guidance Notes for the Canadian Energy Regulator Onshore Pipeline Regulations · Canada Energy Regulator (CER)
  14. 14.Pipeline Rules, Alberta Regulation 125/2023 (office consolidation, with amendments up to AR 8/2026) · Alberta King's Printer
  15. 15.The Pressure Systems Safety Regulations 2000 (SI 2000/128), regulation 14, Keeping of records · legislation.gov.uk, The National Archives (Open Government Licence)
  16. 16.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918-08) · US Occupational Safety and Health Administration (OSHA)
  17. 17.RAGAGEP in Process Safety Management Enforcement (memorandum to regional administrators) · US Occupational Safety and Health Administration (OSHA) ·
  18. 18.Pipeline Transportation Safety Investigation Report P18H0088: Pipeline rupture and fire, Westcoast Energy Inc., Prince George, British Columbia · Transportation Safety Board of Canada (TSB)