What is NACE MR0175/ISO 15156 (materials for sour service)?
NACE MR0175/ISO 15156 is a standard for selecting and qualifying metals that resist hydrogen sulfide (H2S) cracking in oil and gas production. It also covers gas sweetening plants. Its three parts deal with general principles, carbon and low-alloy steels, and corrosion-resistant alloys. ISO states it is not necessarily applicable to refinery equipment.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
A common assumption is that this standard governs all equipment that sees H2S, but ISO limits it to production and gas sweetening and says it is not necessarily applicable to refining and downstream equipment 1. Within that scope the concern is cracking of pressure-containing parts, which is why US offshore and federal onshore rules require H2S-exposed wellheads, blowout preventers and similar equipment to meet MR0175 6,9. OSHA guidance adds that very small hard zones at welds can start significant cracks in wet H2S service, and that weld hardness limits alone may not fully prevent this 10.
What does NACE MR0175/ISO 15156 cover?
ISO describes the series as principles, requirements and recommendations for choosing and qualifying metallic materials for equipment in oil and gas production and gas sweetening plants where H2S is present and a failure could endanger health, safety or the environment 1. It addresses every H2S cracking mechanism in metals: sulfide stress cracking (SSC), stress corrosion cracking, hydrogen-induced cracking (HIC) and stepwise cracking, stress-oriented hydrogen-induced cracking (SOHIC), soft zone cracking and galvanically induced hydrogen stress cracking 1. The main forms are compared in HIC vs SOHIC vs SSC.
It adds to the materials rules of design codes and regulations rather than replacing them, and it assumes load-controlled design 1.
How is the standard organized?
| Part | Title (short form) | What it deals with |
|---|---|---|
| 1 | General principles for selection of cracking-resistant materials | Scope, H2S cracking mechanisms, and how materials are selected and qualified 1,8 |
| 2 | Cracking-resistant carbon and low-alloy steels, and the use of cast irons | Carbon and low-alloy steels and cast irons 3,4 |
| 3 | Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys | Corrosion-resistant and other alloys; see What are corrosion-resistant alloys (CRAs)? 4 |
Sources: ISO 1; UNE 3; GlobalSpec 4; 43 CFR 3176.11 8.
Changes between editions are issued as technical circulars, listed for the parts in 2021 and 2022 4. The current ISO edition of Part 1 is the fourth, published in November 2020; as of 25 October 2026, ISO lists it as subject to revision, with a fifth edition registered as a final draft (FDIS) on 2 October 2026 1,2.
Where did MR0175 come from, and who maintains it now?
MR0175 began at NACE International, now the Association for Materials Protection and Performance (AMPP). A 1999 conference paper (CORROSION 99, now sold by AMPP) records that it became an industry standard for Christmas tree valves in 1975 and was widened in 1978 to other production and completion equipment, after equipment failures 5. An ISO working group, ISO/TC 67/WG 7, was then preparing a separate sour gas document 5.
The US edition carries both designations, for example ANSI/NACE MR0175-2021/ISO 15156-1:2020 8.
Which regulations reference it?
| Regulator | Rule | What it requires |
|---|---|---|
| Bureau of Safety and Environmental Enforcement (BSEE), US offshore | 30 CFR 250.490(p), 250.198 | H2S-resistant metallurgy in zones with H2S or where H2S partial pressure in produced fluid may exceed 0.05 psi; blowout preventer, wellhead and pressure-control equipment to NACE MR0175-2003; minimal welding, done so welds resist SSC 6,7 |
| Bureau of Land Management (BLM), federal and Indian onshore leases | 43 CFR 3176.8, 3176.9 | H2S-exposed drilling and production equipment to NACE MR 0175-2021 (1990 to 2021 editions accepted); production facilities with 100 ppm or more H2S in the gas 8,9 |
BLM defines the metallurgical properties it means: steel grade, processing route (rolled, normalized, tempered or quenched) and resulting strength, judged against H2S concentration, fluid pH, pressure and temperature 9. See Sour service.
How is it used on a project?
- Define the environment. Materials are chosen for the working environment, which BLM describes by H2S concentration, fluid pH, pressure and temperature 9.
- Select or qualify the material. Materials come from the applicable part or are qualified by testing, as the scope's "selecting and qualifying" indicates 1.
- Control strength, hardness and welds. Hydrogen damage becomes more likely as hardness and strength rise 10.
- Buy to it. Product specifications refer to it; the higher product level of API Spec 5CRA covers alloy tubulars meant to resist cracking under the ISO 15156:2020 series 11.
Where integrity problems show up
| Decision or step at this stage | What it affects later | In the Library |
|---|---|---|
| Classifying equipment as sour service | Whether cracking-resistant materials are specified at all; regulators set their own triggers, such as 0.05 psi H2S partial pressure offshore 6 | Sour service |
| Choosing steel grade, heat treatment and strength | Susceptibility to hydrogen damage rises with hardness and strength 10; BLM ties compliance to all three 9 | Sulfide stress cracking |
| Qualifying weld procedures and checking weld hardness | Small hard zones that ordinary hardness tests miss can start cracks 10 | HIC vs SOHIC vs SSC |
| Choosing plate for new wet H2S vessels | OSHA lists lower-strength steels for new vessels; blisters can grow stepwise into through-wall cracks 10 | Hydrogen induced cracking |
| Applying a production standard to refinery equipment | ISO says it is not necessarily applicable to refining 1 | What is wet hydrogen sulfide (H2S) damage? |
Sources: ISO 1; 30 CFR 250.490 6; 43 CFR 3176.8 9; OSHA Technical Manual, Section IV, Chapter 3 10.
Common questions
- Does NACE MR0175 apply to refineries?
- Not necessarily. MR0175/ISO 15156 covers oil and gas production and gas sweetening, and ISO says it is not necessarily applicable to refining and downstream equipment.
- Is NACE MR0175 still a separate standard?
- No. The current edition is one joint document that carries both designations, for example ANSI/NACE MR0175-2021/ISO 15156-1:2020, the edition US federal onshore rules incorporate by reference.
- Does meeting MR0175 prevent all H2S damage?
- No. It addresses cracking resistance, not general metal loss, and OSHA notes weld hardness limits may not be completely effective on their own in wet H2S service.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.ISO 15156-1:2020, Petroleum and natural gas industries: Materials for use in H2S-containing environments in oil and gas production, Part 1: General principles for selection of cracking-resistant materials (standard page) (4th edition, 2020) · International Organization for Standardization (ISO)
- 2.ISO/FDIS 15156-1 (standard under development, page) (5th edition, in development) · International Organization for Standardization (ISO)
- 3.ISO 15156-2:2020, Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (catalog page) · UNE (Spanish Association for Standardization)
- 4.NACE MR0175/ISO 15156, Part 3 (document history and part titles) · GlobalSpec Engineering360 standards catalog
- 5.MR0175: A History and Development (D.H. Patrick, CORROSION 99 paper 99418, store page with abstract) · Association for Materials Protection and Performance (AMPP)
- 6.30 CFR 250.490, Hydrogen sulfide · eCFR, US Office of the Federal Register
- 7.30 CFR 250.198, Documents incorporated by reference · eCFR, US Office of the Federal Register
- 8.43 CFR 3176.11, Incorporation by reference · eCFR, US Office of the Federal Register
- 9.43 CFR 3176.8, Drilling/completion/workover requirements, and 3176.9, Production facilities · eCFR, US Office of the Federal Register
- 10.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
- 11.2025 Publications Catalog (entry for Spec 5CRA/ISO 13680:2020) · American Petroleum Institute (API)