Skip to content
Beaconby Winda
FactEngineering Design and Materials · Materials and welding

What is post-weld heat treatment (PWHT)?

·4 sources

Short answer

Post-weld heat treatment (PWHT) is controlled reheating of a completed weld or component, holding it at temperature and cooling it at a controlled rate. It lowers the residual stress left by welding and tempers hard zones in the weld and heat-affected zone. ASME Section VIII and other codes set when it is required.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

In an industry survey of 294 amine plants summarized in the OSHA Technical Manual, about 40% reported cracking, every crack was in or near a weld, and the cracks were found mainly in welds that had not been post-weld heat treated 1. The same guidance names vessels whose fabrication welds were never heat treated, and repaired vessels without PWHT, as the places to focus inspection in amine, wet hydrogen sulfide (H2S), ammonia, deaerator and caustic digester service 1. The PWHT decision made at fabrication therefore guides where inspection looks for the life of the equipment 1.

What does PWHT do to a weld?

A 1990 assessment by the US National Institute of Standards and Technology (NIST) describes welds that were never thermally stress relieved as a prime source of residual stress 2.

Heat treatment also changes the metal. Both effects matter for cracking: NIST notes that susceptibility to stress corrosion cracking rises with hardness and strength, and lists the heat-affected zone of welds without PWHT as a typical susceptible condition 2. OSHA adds that in wet H2S service, PWHT appears to reduce both the likelihood and the severity of cracking 1.

When is PWHT required?

  • By the construction code. ASME Section VIII, Division 1 (2025 edition) is ASME's construction code for pressure vessels, taking a vessel from design and fabrication through to inspection, testing and certification 4; NIST notes that Section VIII specifies preheat and PWHT requirements for welded construction 2.
  • By the service. OSHA's survey summaries tie cracking at as-welded joints to amine, wet H2S, ammonia, deaerator and caustic digester service 1. API RP 945 (4th edition, September 2022) covers carbon steel fabrication, inspection and repair for avoiding environmental cracking in amine units 3.

What are the limits and side effects of PWHT?

  • It does not repair existing cracks. For older ammonia vessels, OSHA calls the benefit of stress relief doubtful, partly because small undetected cracks may already be present 1.
  • Repairs are harder. NIST notes that repair welds should generally receive PWHT, especially in cracking-prone service, but that this is not always possible and codes give alternatives 2.

Where integrity problems show up

Decision or step at this stageWhat it affects laterIn the Library
Leaving carbon steel welds as-welded in amine serviceCracking in or near welds, found mainly at joints without PWHT 1What is amine corrosion and amine cracking?
Stress relieving vessels in hot caustic service, or notCaustic stress corrosion cracking at welds; in pulp digesters, fully stress-relieved vessels were less susceptible 1,2What is caustic stress corrosion cracking?
Controlling weld hardness and PWHT in wet H2S serviceCracks starting at small hard zones in welds; PWHT appears to reduce them 1What is wet hydrogen sulfide (H2S) damage?
Leaving deaerator welds without PWHTCorrosion fatigue cracking, generally limited to welds without PWHT 1What is corrosion fatigue?
Fabricating ammonia storage spheres as-weldedStress corrosion cracking in or near welds; stress relief is a mitigation for new vessels 1What is stress corrosion cracking (SCC)?
Leaving welds with high residual stress in steel used near its toughness transitionBrittle fracture, which needs a flaw, high stress and low toughness 2What is brittle fracture?
Recording the type, extent and conditions of PWHT in the vessel fileOSHA lists these, and whether weld examination came before or after PWHT, among the information needed for in-service safety assessment 1What documents are handed over when a project is completed?

Sources: OSHA Technical Manual, Section IV, Chapter 3 1; NIST SP 780, 1990 2.

Common questions

What is the difference between preheat and PWHT?
Preheat warms the joint before and during welding; PWHT is a separate heat treatment after welding that relieves residual stress. ASME Section VIII sets requirements for both in welded vessel construction.
Which services make PWHT matter most?
OSHA's survey summaries link cracking at welds left in the as-welded condition to amine, wet hydrogen sulfide, ammonia, deaerator and caustic service.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
  2. 2.NIST Special Publication 780, Guidelines for Pressure Vessel Safety Assessment (S. Yukawa) · US National Institute of Standards and Technology (NIST)
  3. 3.2025 Publications Catalog (entry for RP 945) · American Petroleum Institute (API)
  4. 4.BPVC.VIII.1, BPVC Section VIII, Rules for Construction of Pressure Vessels, Division 1 (product page) (2025) · American Society of Mechanical Engineers (ASME)