How do protective coatings prevent corrosion?
Protective coatings prevent corrosion mainly by separating steel from its environment: they keep out water, oxygen and salts and add electrical resistance. Some also protect chemically, through inhibitive pigments, or sacrificially, through zinc. US rules require most buried and submerged steel pipelines to be both coated and cathodically protected (49 CFR 192.455, 195.557, 195.563).
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
On July 25, 2010, a 30-inch crude oil pipeline ruptured in a wetland at Marshall, Michigan 1. The National Transportation Safety Board (NTSB) found the probable cause was corrosion fatigue cracking that grew from cracks and corrosion beneath polyethylene tape coating that had come loose (disbonded) 1. Pipe-to-soil readings taken six days later showed cathodic protection above the minimum criteria of 49 CFR 195.571, yet the NTSB noted that disbonded tape can shield the steel from that current 1. Cleanup costs exceeded $767 million when the report was adopted in 2012 1.
How does a coating protect steel?
Steel rusts only when water and oxygen are both present 5. Coatings act in three ways:
- Barrier. The film excludes air and moisture and puts a high-resistance layer into the corrosion cell 3. For buried pipelines, US rules require coatings that adhere well enough to stop moisture creeping underneath, resist cracking, survive handling and soil stress, and work with cathodic protection; insulating types must absorb little moisture and resist electric current (49 CFR 192.461) 9.
- Inhibitive. Primers with pigments such as zinc phosphate interfere with corrosion where the film is broken 5.
- Sacrificial. Zinc-rich primers and galvanizing contain a metal more reactive than steel, which corrodes first at a break until it is used up 5,12.
For paints, the UK National Physical Laboratory (NPL) notes that protection generally rises in proportion to dry film thickness 5.
Which coatings are used in oil and gas?
| Coating | Where it is used | Strengths | Weaknesses |
|---|---|---|---|
| Fusion-bonded epoxy (FBE) | Factory-applied line pipe; inside and outside of well tubulars 7,12 | Most widely used pipe coating today; tolerates high temperature and stress 7 | Disbondment may increase toward the end of design life 3 |
| Three-layer polyethylene or polypropylene (epoxy primer, adhesive, extruded outer layer) | Factory-applied line pipe 3 | Abrasion and chemical resistant; needs very little cathodic protection current 3 | Thick, heavy and expensive 3 |
| Coal tar and bitumen enamels | Older pipelines and field application 3,7 | Coal tar has a long service record 3 | Coal tar is a health hazard during application; bitumen absorbs moisture 3 |
| Tape systems (primer, mastic, inner and outer wraps) | Field joints, fittings, repairs, bare pipe 3 | Applied by hand or machine, usually with about 55% overlap 3 | Early tape wraps were prone to disbonding 7 |
| Paint systems (primer, intermediate, finish) | Structures, plant, above-ground pipe 5 | No size limit; thicker films last longer 5 | Need a very clean surface; usually outlived by the plant 4,11 |
| Hot-dip galvanizing and thermal spray (zinc, aluminum) | Structural steel and components 5 | Very long life to first maintenance when sealed and painted 5 | Higher cost than paint 5 |
| Internal linings (epoxy, cement, ceramic) | Lines where product treatment is not feasible, such as gathering lines 7 | Protect the inner wall; smoother flow 12 | Not widely used in oil and gas pipelines 7 |
Sources: NPL Guides No. 3 and 4 3,5; PHMSA 7; Solovyeva et al., 2023 12.
Why does surface preparation matter?
NPL describes correct surface preparation as the most important factor in a coating's success 4. Small amounts of oil, grease or oxide weaken adhesion, and invisible soluble salts such as chlorides and sulfates draw moisture through the film and cause early failure 4. Automated abrasive blast cleaning can remove all mill scale and rust, while hand and power tools are roughly 30 to 50% effective; any re-rusting before coating counts as contamination 4. US rules require pipeline coatings to be applied on a properly prepared surface (49 CFR 192.461) 9, and PHMSA notes that factory coating gives cleaner steel and better-controlled conditions, leaving only girth welds to coat in the field 7.
Why do coatings fail?
- Disbonding. The coating separates from the steel, water collects beneath it, and the film can block cathodic protection current 1,7.
- Mechanical damage. Equipment, rocks left in backfill and later excavation damage coatings 7,2.
- Age. NPL notes that coat-and-wrap systems break down with time, and that a coating usually wears out before the structure it protects 3,11.
- Too much cathodic protection. Excessive negative potentials create alkaline conditions and hydrogen at the steel that can disbond coatings 6; US rules require the amount of protection to be controlled so it does not damage the coating or pipe (49 CFR 192.463) 9.
How is coating condition checked?
- Before burial: external coating is inspected just before the pipe is lowered into the ditch, and damage is repaired (49 CFR 192.461, 195.561) 9,10.
- After backfill: onshore gas transmission operators survey coating with direct or alternating current voltage gradient methods within 6 months of backfilling 1,000 feet or more of repaired or replaced pipe, and repair damage classed as severe within 6 months (49 CFR 192.461) 9.
- In service: above-ground surveys include alternating current voltage gradient, current attenuation, close interval potential and direct current voltage gradient methods 3. PHMSA notes close interval surveys miss very small holidays and do not work where coating is disbonded, in rocky terrain or under paving 8.
- Paint films: dry film thickness is usually measured with an electromagnetic induction gauge 5.
Where integrity problems show up
| Where it occurs (unit or equipment) | Conditions that drive it | How it is usually found | In the Library |
|---|---|---|---|
| Tape-coated crude oil pipeline through a wetland 1 | Tape wrinkled and tented over the seam and disbonded; wet and dry cycles; current shielded 1 | In-line crack and metal loss tools; a 2005 crack inspection had reported crack-like defects in the segment, which was not excavated 1 | What is stress corrosion cracking in pipelines (high-pH and near-neutral pH)? |
| Coated gas line in rocky backfill 2 | Rocks damaged the coating and shielded the pipe; over 70% wall loss 2 | In-line inspection or pressure testing, which the NTSB concluded would likely have revealed it 2 | How does cathodic protection work? |
| Coated pipe after repair or replacement | Damage during handling and backfill 9 | Voltage gradient coating survey within 6 months (49 CFR 192.461) 9 | Coating holiday |
| Thermally insulated pipe | Water through a damaged outer jacket; cathodic protection unlikely to help 3 | Atmospheric inspections with particular attention under thermal insulation (49 CFR 192.481) 9 | What is corrosion under insulation (CUI)? |
| Pipe at soil-to-air interfaces, supports and splash zones | Coating breakdown in air 9 | Visual inspection at least every 3 calendar years onshore, every year offshore (49 CFR 192.481) 9 | What is atmospheric corrosion? |
Sources: NTSB PAR-12/01 1 and PAR-14/01 2; NPL Guide No. 4 3; 49 CFR 192 Subpart I 9.
Common questions
- Is a coating holiday the same as disbondment?
- No. A holiday is a gap that leaves bare steel, which cathodic protection current can reach. A disbonded coating is still present but has lost adhesion; water trapped beneath it can corrode the steel while the film blocks the current, as the NTSB found at Marshall and Sissonville.
- Why add cathodic protection to a coated pipe?
- Coatings always have some flaws or damage, and cathodic protection covers the exposed steel; the coating in turn cuts the current needed. US rules require any externally coated buried pipeline under Part 192 to be cathodically protected (49 CFR 192.455).
- Does a concrete weight coating prevent corrosion?
- No. Concrete on underwater pipelines provides negative buoyancy and is applied over the anti-corrosion coating, though its application can affect that coating.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Pipeline Accident Report NTSB/PAR-12/01: Enbridge Incorporated Hazardous Liquid Pipeline Rupture and Release, Marshall, Michigan, July 25, 2010 · US National Transportation Safety Board (NTSB)
- 2.Pipeline Accident Report NTSB/PAR-14/01: Columbia Gas Transmission Corporation Pipeline Rupture, Sissonville, West Virginia, December 11, 2012 · US National Transportation Safety Board (NTSB)
- 3.Guides to Good Practice in Corrosion Control No. 4: Corrosion Control for Buried Pipelines (D. W. Harvey) · National Physical Laboratory (NPL), UK
- 4.Guides to Good Practice in Corrosion Control No. 2: Surface Preparation for Coating (R. Hudson) · National Physical Laboratory (NPL), UK
- 5.Guides to Good Practice in Corrosion Control No. 3: Coating for the Protection of Structural Steelwork (R. Hudson) · National Physical Laboratory (NPL), UK
- 6.Guides to Good Practice in Corrosion Control No. 1: Cathodic Protection (D. W. Harvey) · National Physical Laboratory (NPL), UK
- 7.Fact Sheet: Pipe Coatings · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
- 8.Fact Sheet: Close Interval Survey · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
- 9.49 CFR Part 192, Subpart I, Requirements for Corrosion Control (192.455, 192.461, 192.463, 192.479, 192.481) · eCFR, US Office of the Federal Register
- 10.49 CFR Part 195, Subpart H, Corrosion Control (195.557 to 195.563) · eCFR, US Office of the Federal Register
- 11.Guides to Good Practice in Corrosion Control No. 11: Corrosion control checklist · National Physical Laboratory (NPL), UK
- 12.Current Downhole Corrosion Control Solutions and Trends in the Oil and Gas Industry: A Review (V. A. Solovyeva, K. H. Almuhammadi, W. O. Badeghaish), Materials 16(5):1795 · MDPI (open access, CC BY 4.0) ·