Skip to content
Beaconby Winda
FactAsset Integrity Management · Pipeline integrity

What is ASME B31.8S?

·7 sources

Short answer

ASME B31.8S is the ASME standard for building an integrity management program for onshore gas pipeline systems made of ferrous materials. Its title is Managing System Integrity of Gas Pipelines. US federal rules for gas transmission integrity management (49 CFR 192, Subpart O) incorporate its 2018 edition; ASME's latest edition is 2025.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

The edition of ASME B31.8S that US federal rules enforce is not the newest one. The federal list of incorporated documents, 49 CFR 192.7, names the 2018 edition (issued November 28, 2018) and ties it to 15 sections of Part 192, while ASME's product page lists a 2025 edition 1,2. Subpart O tells operators to follow B31.8S and its appendices where the rule says so, and states that the rule wins wherever the two conflict 3. For US compliance, the text that applies is therefore the 2018 edition read together with Subpart O 2,3.

What does ASME B31.8S cover?

ASME B31.8S, Managing System Integrity of Gas Pipelines, belongs to ASME's B31 family of piping standards 1. ASME's product page describes it as a basis for building and running an integrity management program, for onshore gas systems made of ferrous material, taking in the line pipe and also the stations, storage and other equipment connected to it 1. The page lists eight editions, from 2010 to the current 2025 edition 1.

How do US rules use B31.8S?

The US Pipeline and Hazardous Materials Safety Administration (PHMSA) issued the gas transmission integrity management rule at 68 FR 69778, effective February 14, 2004, and operators had until December 17, 2004, to put written programs in place 4,5,3. The rule points to B31.8S for specific tasks:

Subpart O sectionWhat the rule takes from B31.8S
192.903, high consequence area (HCA) definitionPotential impact radius for gases other than natural gas (B31.8S section 3.2)
192.907(b)Follow B31.8S and its appendices where specified; Subpart O controls in a conflict
192.911(i) and (l)Performance plan (section 9) and quality assurance process (section 12)
192.913(a)Features of prescriptive and performance-based programs
192.917(a) to (c)Threats listed in section 2; data gathering and integration (section 4); risk assessment (section 5)
192.921(a)(2) and 192.939Test pressures and reassessment intervals (Table 5.6.1-1 of section 5)
192.923(b)(1)External corrosion direct assessment (section 6.4, with NACE SP0502)
192.945(a)Four overall performance measures (section 9.4) and threat-specific measures (Appendix A), reported yearly

Source: 49 CFR 192.7 and Subpart O, eCFR, up to date as of 22 Oct 2026 2,3.

Subpart O itself lists the threats an operator must consider, in four groups: time-dependent threats such as internal and external corrosion and stress corrosion cracking; stable threats such as manufacturing, welding and construction defects; time-independent threats like damage by third parties, incorrect operation, and weather or outside force; and human error 3.

Worked example of the federal impact radius formula (illustrative numbers, not from any real asset or standard table). 49 CFR 192.903 sets the potential impact radius for natural gas as r = 0.69 × √(p × d²), with r in feet, p the maximum allowable operating pressure (MAOP) in psi and d the nominal diameter in inches 3. For p = 1,000 psi and d = 30 inches, r = 0.69 × √900,000 ≈ 655 feet (about 200 m). Buildings and identified sites inside that circle decide whether the segment lies in an HCA 3.

What are prescriptive and performance-based programs?

Subpart O states that B31.8S gives the essential features of both 3. PHMSA describes the rule as largely prescriptive, with fixed deadlines, reassessment intervals and remediation times 5. An operator that shows exceptional performance, including a full risk analysis, a data integration process, semi-annual performance measures and at least two assessments of each covered segment, may deviate only on reassessment timing, with some reassessment still within 7 years, and on remediation timing 3.

Where integrity problems show up

DecisionData it depends onWhat goes wrong without itIn the Library
Which segments the program coversMAOP and diameter for the impact radius; buildings and identified sites inside it 3A Class 2 segment near Sissonville, West Virginia, lay outside any HCA, was not in the operator's program and had not been inspected or tested after 1988; it ruptured in 2012 with more than 70% wall loss 6High consequence area
Which threats apply to a segmentIntegrated pipe, coating, cathodic protection, test, assessment and monitoring data, including gas stream sampling 3Before the 2000 Carlsbad, New Mexico, rupture, the National Transportation Safety Board (NTSB) found, gas quality monitoring and sampling of removed liquids would likely have shown the corrosion potential 7What is corrosion monitoring and which methods are used?
How to assess each threatThreats per segment; methods from in-line inspection to direct assessment 3Direct assessment may not be used for threats other than external and internal corrosion and stress corrosion cracking 3What is direct assessment (ECDA, ICDA, SCCDA)?
Whether findings apply to similar pipeCorrosion and crack findings, material, coating and environment 3At Sissonville, 2009 in-line inspection data showing external corrosion on two adjacent HCA lines was not adequately considered for the line that failed 6What is pipeline integrity management?

Sources: 49 CFR 192 Subpart O 3; NTSB/PAR-14/01, 2014 6; NTSB/PAR-03/01, 2003 7.

Common questions

Is B31.8S the same as B31.8?
No. 49 CFR 192.7 lists two separate 2018 documents. ASME B31.8, Gas Transmission and Distribution Piping Systems, is cited for a few design and operating sections; ASME B31.8S, Managing System Integrity of Gas Pipelines, for the integrity management subpart. See [ASME B31.3 vs B31.4 vs B31.8: which piping code applies?](/library/asme-b31-3-vs-b31-4-vs-b31-8/).
What is the liquid pipeline counterpart?
API Recommended Practice (RP) 1160, Managing System Integrity for Hazardous Liquid Pipelines; API's 2025 catalog lists the 3rd edition, February 2019, reaffirmed March 2024. See [What is API 1160 (integrity management for hazardous liquid pipelines)?](/library/api-1160/).
Does B31.8S apply outside high consequence areas?
The standard's principles apply to the whole system, while Subpart O's requirements apply to covered segments in HCAs. After Sissonville, the NTSB recommended adding major roads to the sites that create an HCA.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.B31.8S, Managing System Integrity of Gas Pipelines (product page) (2025 (editions listed: 2025, 2022, 2020, 2018, 2016, 2014, 2012, 2010)) · American Society of Mechanical Engineers (ASME)
  2. 2.49 CFR 192.7, What documents are incorporated by reference partly or wholly in this part? (incorporates ASME B31.8S-2018, issued November 28, 2018) · eCFR, US Office of the Federal Register
  3. 3.49 CFR Part 192, Subpart O, Gas Transmission Pipeline Integrity Management · eCFR, US Office of the Federal Register
  4. 4.Gas Transmission Integrity Management (GT IM) Overview · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
  5. 5.GT IM Fact Sheet · US Pipeline and Hazardous Materials Safety Administration (PHMSA)
  6. 6.Pipeline Accident Report: Columbia Gas Transmission Corporation Pipeline Rupture, Sissonville, West Virginia, December 11, 2012 (NTSB/PAR-14/01) · US National Transportation Safety Board (NTSB)
  7. 7.Pipeline Accident Report: Natural Gas Pipeline Rupture and Fire Near Carlsbad, New Mexico, August 19, 2000 (NTSB/PAR-03/01) · US National Transportation Safety Board (NTSB)