Skip to content
Beaconby Winda
FactProcurement and Supply Chain · Fabrication quality

How is fabrication quality controlled for pressure equipment?

·12 sources

Short answer

Fabrication quality for pressure equipment is controlled by the maker's written quality control system and by independent checks at set steps. The checks cover incoming material, welding with qualified procedures and welders, heat treatment, nondestructive examination, dimensions and the final pressure test. For ASME code items, an Authorized Inspector certifies compliance on the manufacturer's data report.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

During 2008 and 2009 construction, several new large-diameter pipelines had girth welds fail in hydrostatic tests, leak or fail in service; the US Pipeline and Hazardous Materials Safety Administration (PHMSA) traced them to misaligned welds, improper bevels and nondestructive testing that was not set up for the joint or not done to procedure 1. Poor control can also stay hidden for decades. The US National Transportation Safety Board (NTSB) found that inadequate quality control in 1956 let pipe with visibly defective seam welds into service at San Bruno, California, with no records of radiography or pressure testing; it ruptured 54 years later 2.

Who controls fabrication quality?

Under the ASME Boiler and Pressure Vessel Code (BPVC), the manufacturer is responsible for meeting the code, and ASME certifies the manufacturer's quality control system before it may mark items with the ASME certification mark 3,5. ASME has certified such systems since 1916 and listed more than 6,800 certificate holders when its page was checked in October 2026 3. To gain or renew a certificate, the maker's quality control manual is reviewed and the whole system, including actual welding, is demonstrated on real code work or a mock-up 4.

PartyRole during fabricationSource
ManufacturerRuns the written quality control system; responsible for code compliance and the order3,5
Authorized Inspector (from an Authorized Inspection Agency)Accepts the quality control manual, inspects during construction, including against drawing dimensions, and certifies the data report4,5
Purchaser or its source inspectorChecks against the purchase specification at points agreed in the inspection and test plan5
Plant owner under US process safety rulesMust make sure equipment as fabricated suits the process and is installed as designed12

What is checked during fabrication?

US nuclear quality rules, a public model for such controls, require welding, heat treating and nondestructive testing to be done by qualified people using qualified procedures 8. ASME BPVC Section VIII, Division 1 (2025 edition) covers design, fabrication, inspection, testing and certification of vessels above 15 pounds per square inch gauge (psig), and Section IX (2025 edition) covers welding, brazing and fusing qualifications 6,7.

StageWhat is checkedRecord it leaves
Material receiptCertificates against the order and specification; marking; alloy check where requiredMill test certificates, receiving record, PMI report
Cutting, forming, fit-upDimensions and tolerances on drawings, which carry the design calculationsDimensional report 5
WeldingQualified welding procedures and qualified weldersWelding procedure and qualification records, weld map 7,8
Heat treatmentWhether post-weld heat treatment (PWHT) was done, its type, extent and conditionsTime and temperature chart 9
Nondestructive examination (NDE)Method and extent, and whether done before or after PWHT and the pressure testNDE reports; examiner qualifications 9,10
Pressure test and final inspectionTest result; visual check for material and dimensional defectsTest record, nameplate, manufacturer's data report (ASME U-1 or U-2) 5,9

Sources: OSHA Technical Manual, Section IV, Chapter 3 9; National Board 5; ASME product pages 6,7; 10 CFR 50 Appendix B, Criterion IX 8; NIST SP 780, 1990 10.

How is fabrication quality documented?

Records are the evidence that checks happened. The nuclear rule asks that inspection and test records name the inspector, the type of observation, the result, its acceptability and any action on deficiencies 8, and ASME's joint review asks to see records of all code work since the previous review 4. OSHA's pressure vessel guidelines list what a later safety assessment needs from construction: serial number and data report, design code, material specifications, corrosion allowance, PWHT details, and the type, extent and timing of weld examinations 9. Where such records were never made, as for the 1956 San Bruno work, nothing shows what was checked 2.

Where integrity problems show up

Decision or step at this stageWhat it affects laterIn the Library
Leaving welds without PWHT in amine, wet hydrogen sulfide, ammonia or deaerator serviceService cracking concentrates in or near as-welded seams; in a survey of 294 amine plants, about 40% reported cracking 9,10What is post-weld heat treatment (PWHT)?; What is amine corrosion and amine cracking?
Not post-weld heat treating carbon steel exchanger shells in hot hydrogen serviceAt Anacortes, Washington, in 2010, hydrogen attack was found only near non-PWHT welds, along which the shell ruptured 11What is high temperature hydrogen attack (HTHA)?
Controlling weld hardness for wet hydrogen sulfide serviceCracks can start at small hard zones near welds that conventional hardness tests do not detect 9What is wet hydrogen sulfide (H2S) damage?
Setting up and following NDE procedures for each jointSome girth welds that failed in service had NDE procedures that were not optimized or not completed as required 1Radiographic vs ultrasonic testing for welds
Finding flaws before the equipment leaves the shopIn a survey of 141 liquefied petroleum gas vessels, 30% had cracking, a considerable part of it preexisting fabrication flaws found by more sensitive methods 10How are crack-like flaws assessed for fitness-for-service?
Keeping construction records with the vesselThey are inputs to later safety assessment 9What documents are handed over when a project is completed?

Sources: OSHA Technical Manual, Section IV, Chapter 3 9; NIST SP 780, 1990 10; CSB Anacortes report, 2014 11; PHMSA Advisory Bulletin ADB-10-03, 2010 1.

Common questions

What is the difference between quality assurance and quality control?
In the US nuclear rule's terms, quality assurance is all the planned and systematic actions that give confidence an item will perform in service, and quality control is the part of it that measures and controls physical characteristics against set requirements. See [Quality assurance vs quality control in construction](/library/qa-vs-qc-construction/).
Does a code stamp mean the vessel suits its service?
Not by itself. The stamp shows construction to the code, while OSHA notes that the chemical environment strongly affects cracking and is not explicitly treated in most design codes. Under US process safety rules, the owner must make sure equipment as fabricated suits the process.
Does fabrication quality control cover the vessel after start-up?
No. NIST noted in 1990 that design and construction codes contain no rules for in-service inspection; that is handled by documents such as API 510 and the National Board Inspection Code.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Pipeline Safety: Girth Weld Quality Issues Due to Improper Transitioning, Misalignment, and Welding Practices of Large Diameter Line Pipe (Advisory Bulletin ADB-10-03), 75 FR 14243 · US Pipeline and Hazardous Materials Safety Administration (PHMSA), via Federal Register (govinfo) ·
  2. 2.Pacific Gas and Electric Company Natural Gas Transmission Pipeline Rupture and Fire, San Bruno, California, September 9, 2010 (NTSB/PAR-11/01) · US National Transportation Safety Board (NTSB)
  3. 3.Boiler and Pressure Vessel Certification · American Society of Mechanical Engineers (ASME)
  4. 4.Information and Description of the ASME Joint Review Process for Applicant's Applying for ASME Boiler and Pressure Vessel Code Certification · American Society of Mechanical Engineers (ASME)
  5. 5.The Authorized Inspector's Responsibility for Dimensional Inspection (National Board BULLETIN, Classic Series) · National Board of Boiler and Pressure Vessel Inspectors
  6. 6.BPVC.VIII.1, BPVC Section VIII, Rules for Construction of Pressure Vessels, Division 1 (product page) (2025) · American Society of Mechanical Engineers (ASME)
  7. 7.BPVC.IX, BPVC Section IX, Welding, Brazing, and Fusing Qualifications (product page) (2025) · American Society of Mechanical Engineers (ASME)
  8. 8.10 CFR Part 50, Appendix B, Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants · eCFR, US Office of the Federal Register
  9. 9.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
  10. 10.NIST Special Publication 780, Guidelines for Pressure Vessel Safety Assessment (S. Yukawa) · US National Institute of Standards and Technology (NIST)
  11. 11.Investigation Report: Catastrophic Rupture of Heat Exchanger (Seven Fatalities), Tesoro Anacortes Refinery, Anacortes, Washington, April 2, 2010 (Report 2010-08-I-WA) · US Chemical Safety and Hazard Investigation Board (CSB)
  12. 12.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register