Skip to content
Beaconby Winda
FactOil, Gas and Chemicals Basics · Facilities and processes

What is hydroprocessing (hydrotreating and hydrocracking)?

·10 sources

Short answer

Hydroprocessing is the group of refinery processes that react oil fractions with hydrogen over a catalyst at high temperature and pressure. Hydrotreating removes sulfur, nitrogen, oxygen and metals with little change in molecule size; hydrocracking also breaks heavy gas oils into diesel, jet fuel and naphtha. Hot hydrogen makes high temperature hydrogen attack a key integrity concern.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

What is the difference between hydrotreating and hydrocracking?

Both use hydrogen, a catalyst and high pressure 3,6. The difference is the goal: hydrotreating removes impurities and keeps cracking to a minimum, whereas hydrocracking deliberately breaks heavy oil into lighter products 3,2.

HydrotreatingHydrocracking
Main purposeRemove sulfur, nitrogen, oxygen, halides and trace metals; saturate olefins 3Convert heavy gas oil into lighter, saturated products 2
Typical feedsNaphtha, kerosene, diesel and gas oils 3Heavy gas oils from the crude and vacuum columns, the fluid catalytic cracker and the coker 2
Typical conditionsAbout 290 to 430 °C (550 to 805 °F) and 7 to 180 bar (about 100 to 2,600 pounds per square inch) 5About 300 to 400 °C (570 to 750 °F) at 8 to 15 megapascals of hydrogen (about 1,160 to 2,180 pounds per square inch) 4
CatalystCobalt-molybdenum mainly for sulfur, nickel-molybdenum mainly for nitrogen 5Metals that add hydrogen, on an acidic silica-alumina or zeolite support that cracks 4
HeatNet heat release; reactor temperature typically rises 5 to 20 °F (3 to 11 °C) 3Cracking absorbs heat and saturation releases it; hydrogen is injected at several points to hold temperature 2
Main productsSame stream with less sulfur and nitrogenJet fuel, diesel and gasoline components 2

Hydrotreating reactions are mostly kept below about 800 °F (427 °C) so that little cracking occurs, and they use roughly 200 to 800 standard cubic feet of hydrogen for each barrel processed 3. Hydrocracking must saturate aromatic rings with hydrogen before it can break them, and the Penn State course describes it as a costly process 4.

Why do refineries hydrotreat their streams?

  • To meet fuel specifications. Hydrotreaters cut sulfur and nitrogen in finished products such as jet fuel and diesel 3.
  • To protect other catalysts. Nitrogen and sulfur compounds deactivate catalysts, so hydrotreaters sit ahead of units such as the catalytic reformer and the cracking units 1,3.
  • To upgrade heavy, sulfur-rich oil. A hydrocracker can turn high-sulfur material that would otherwise go to marine or boiler fuel into low-sulfur transport fuels 2.

The reactions convert sulfur to hydrogen sulfide, nitrogen to ammonia and oxygen to water, while metals stay behind on the catalyst 3,5.

Where are hydroprocessing units in a refinery?

A large refinery may run five or more hydrotreaters 3. The common ones are:

  • Naphtha hydrotreater: cleans naphtha before the catalytic reformer. 3
  • Kerosene or middle distillate hydrotreater: treats kerosene for jet fuel. 3
  • Gas oil or diesel hydrotreater: treats diesel-range oil or pretreats vacuum gas oil going to a cracking unit. 3

Hydrocrackers are less common; many refiners do not have one 2. All these units need a steady hydrogen supply. Steam methane reforming is the main refinery source, because byproduct hydrogen from the catalytic reformer is generally not enough 9, and some refiners buy hydrogen, including from neighboring steam crackers 10.

How does a hydrotreater work?

  1. Liquid feed is mixed with hydrogen-rich gas 3,7.
  2. The mixture is heated, first in feed/effluent heat exchangers by the hot reactor outlet stream and then in a fired heater 7,6.
  3. It passes through a fixed-bed reactor, where the treating reactions take place 3,6.
  4. The effluent is cooled, and a separator splits hydrogen-rich gas from liquid 3,6.
  5. The gas is treated to remove hydrogen sulfide and recycled to the reactor; a stripper takes the light ends out of the liquid product 3.

In the naphtha hydrotreater that the US Chemical Safety and Hazard Investigation Board (CSB) investigated at Anacortes, naphtha was heated above 600 °F (316 °C) at more than 600 pounds per square inch gauge and mixed with hydrogen before the reactor 7. Condensate is injected into the effluent to stop salts from forming in downstream equipment 5.

Where integrity problems show up

Unit / equipmentTypical integrity issueIn the Library
Feed/effluent heat exchangers, reactor circuit and other carbon steel in hot, high-pressure hydrogenHigh temperature hydrogen attack (HTHA)High temperature hydrogen attack, Anacortes refinery explosion (2010)
Cooler parts of hydrotreaters and reformer pretreater exchangersHydrochloric acid condensing; ammonium chloride corrosion and foulingHydrochloric acid corrosion, Ammonium chloride corrosion
Hydrocracker condensing areasCorrosion by wet carbon dioxideCarbon dioxide corrosion
Recycle gas amine scrubber and amine regeneratorAmine corrosionAmine corrosion

Sources: CSB, Anacortes investigation report (2014) 7 and HTHA safety alert (2016) 8; Occupational Safety and Health Administration (OSHA) Technical Manual, Section IV, Chapter 2 (undated) 6.

HTHA forms fissures and cracks when carbon steel is held in hydrogen at high temperature and pressure; low carbon steels are most susceptible because their carbides react with hydrogen more readily than chromium and molybdenum carbides do 7. At Anacortes in 2010, a carbon steel feed/effluent exchanger in the naphtha hydrotreater ruptured from HTHA, killing seven workers 7. The industry predicts safe operating regions with the Nelson curves in American Petroleum Institute Recommended Practice 941 (API RP 941), Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants; the CSB found HTHA at Anacortes in conditions the carbon steel curve rated as safe, and noted that its microscopic, localized cracks are hard to find by inspection 8.

OSHA also notes that ammonium hydrosulfide, formed from the hydrogen sulfide and ammonia in the reactor effluent, can corrode equipment seriously below the water dew point 6.

Common questions

Is hydrotreating the same as hydrodesulfurization?
Nearly. DOE uses the terms interchangeably, and sulfur removal is the main reaction, but hydrotreating also removes nitrogen, oxygen and metals and saturates olefins (DOE, 2006).
Is high temperature hydrogen attack the same as hydrogen embrittlement?
No. HTHA is the specific high-temperature mechanism described above, in which hydrogen reacts with carbon in the steel to form methane and leaves fissures (CSB, 2014). Hydrogen embrittlement is a separate mechanism with its own page: [What is hydrogen embrittlement?](/library/hydrogen-embrittlement/).
Is hydrocracking the same as fluid catalytic cracking?
No. A hydrocracker adds hydrogen and favors diesel and jet fuel; a fluid catalytic cracker uses no hydrogen, burns coke off its catalyst and favors gasoline (EIA, 2013; Penn State, undated). See [What is fluid catalytic cracking (FCC)?](/library/fluid-catalytic-cracking/).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Glossary: Catalytic hydrotreating · U.S. Energy Information Administration
  2. 2.Hydrocracking is an important source of diesel and jet fuel · U.S. Energy Information Administration, Today in Energy ·
  3. 3.Energy Bandwidth for Petroleum Refining Processes · U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)
  4. 4.FSC 432 Petroleum Refining, Lesson 7: Catalytic Conversion Processes Part 1 · Penn State College of Earth and Mineral Sciences (S. Eser)
  5. 5.An Overview of Hydrotreating · American Institute of Chemical Engineers, Chemical Engineering Progress
  6. 6.OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes · Occupational Safety and Health Administration
  7. 7.Investigation Report: Catastrophic Rupture of Heat Exchanger, Tesoro Anacortes Refinery, Report No. 2010-08-I-WA · U.S. Chemical Safety and Hazard Investigation Board
  8. 8.Safety Alert: Preventing High Temperature Hydrogen Attack (HTHA) · U.S. Chemical Safety and Hazard Investigation Board
  9. 9.AP-42, Section 5.1: Petroleum Refining · U.S. Environmental Protection Agency
  10. 10.The Future of Petrochemicals · International Energy Agency ·