Skip to content
Beaconby Winda

Dye penetrant vs magnetic particle testing

·5 sources

Short answer

Dye penetrant testing (PT) finds flaws open to the surface of almost any non-porous material by drawing a liquid back out of them. Magnetic particle testing (MT) works only on ferromagnetic steels, but it also finds flaws just below the surface, by showing where magnetic flux leaks around them.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

In a case study in UK Health and Safety Executive (HSE) guidance, two stainless steel vessels held a product containing chlorides, a known setting for stress corrosion cracking 1. One leaked during a hydraulic test after a repair and was found to have thousands of tight through-wall cracks; for the second, the examination scheme then specified red-dye penetrant on 10% of the welds 1. An NDT specialist estimated that the method had less than a 30% chance of finding a crack, so with 10% coverage the overall chance of finding a cracked weld was about 3% 1. HSE added that cracks filled with product can defeat penetrant, and that fluorescent dye would have been far more sensitive in the dark vessel 1.

Dye penetrant vs magnetic particle at a glance

Dye penetrant (PT)Magnetic particle (MT)
PrincipleA liquid seeps into open flaws; after the excess is removed, a developer draws it back out as a visible mark 2,4The part is magnetized; flux leaks out at a flaw and fine iron particles gather there 2,5
MaterialsNearly any non-porous material: all metals and many non-metals 2,4Ferromagnetic materials only, which on plant means carbon and low-alloy steels 3,5
Flaws foundOnly those open to the surface 2,3Surface flaws and some just below; OSHA gives a crude limit of about 1.5 to 3 mm depth 3
Flaw orientationNot a factor 2Best when the field crosses the flaw at 45 to 90 degrees, so parts are magnetized in two directions 5
Surface preparationCritical: clean, dry, coating-free; grinding or blasting can smear metal over flaws 1,4Less critical than for some other methods, but finishes must come off and rough surfaces interfere 2,5
TimePenetrant dwell usually 5 to 60 minutes, then at least 10 minutes to develop 4Relatively fast, with immediate results 2
Sensitivity aidsFluorescent penetrant viewed under ultraviolet light 1,3Wet fluorescent particles (WFMT) 1,3
After the testDeveloper cleaned off; chemicals handled and disposed of 4Part demagnetized 2
False indicationsBackground from rough or porous surfaces 2Sharp corners, threads, abrupt changes in shape and residual magnetism 1,2

Sources: HSE COMAH technical measures document 1; FAA AC 43.13-1B, Chapter 5 2; OSHA Technical Manual, Section IV, Chapter 3 3; Iowa State NDE-Ed penetrant and magnetic particle pages 4,5.

When is penetrant testing used?

  • Non-magnetic alloys. PT does not depend on the alloy, so it is used on austenitic stainless steels and non-ferrous metals where MT cannot work 3; HSE calls it the preferred surface technique for non-magnetic materials 1.
  • Open pits and similar surface flaws. HSE notes PT is better suited than MT to volumetric surface defects such as pits, though more affected by surface condition 1.
  • Local checks on complex shapes, since penetrant can be applied from a spray can or swab 4.

On stainless steel, HSE notes that only low-halogen chemicals should be used, so that the test itself does not start stress corrosion cracking 1.

When is magnetic particle testing used?

  • Surface cracks in ferritic steel, where HSE describes MT as generally the preferred method 1.
  • Vessels in cracking services. In OSHA's summary of an amine plant survey, wet fluorescent MT and UT were the main ways cracks were found, with internal WFMT preferred; in pulp digesters, WFMT with proper surface preparation was the most effective method 3.
  • One-sided access on vessels, using prods that pass current through the area between them 3.
  • Offshore and underwater structures and pipelines 5.

Which is more sensitive?

It depends on the setting, and the sources differ. FAA guidance for aircraft parts states that PT is generally more sensitive than MT even on ferromagnetic steel 2. Plant guidance from HSE and OSHA prefers MT, and especially WFMT, for surface cracks in ferritic steel 1,3. Both agree that fluorescent materials raise sensitivity and that tight cracks are the hard case; HSE notes that PT needs a long dwell to find them 1.

Where integrity problems show up

What it finds wellWhat it can miss or get wrongIn the Library
Cracks at welds in carbon steel vessels in amine and caustic service, with WFMT 3Cracks parallel to the field; flaws more than a few millimeters below the surface 3,5What is amine corrosion and amine cracking?, What is caustic stress corrosion cracking?
Corrosion fatigue cracks at deaerator welds, for which industry recommendations cited by OSHA call for WFMT 3Cracks that have not reached the inspected surface, which need volumetric methods 3What is corrosion fatigue?
Surface cracks in austenitic stainless steel, with PT 3Tight or product-filled cracks; red-dye indications in dark, confined spaces 1What is chloride stress corrosion cracking?
Pits open to the surface, with PT 1Rough or porous surfaces; flaws sealed by grinding or blasting 2,4What is pitting corrosion?

Sources: OSHA Technical Manual, Section IV, Chapter 3 3; HSE COMAH technical measures document, including case study 1 1; FAA AC 43.13-1B 2; NDE-Ed 4,5.

Common questions

Can magnetic particle testing be used on stainless steel?
Not on austenitic stainless steel, which is not ferromagnetic; OSHA notes PT is used there instead. HSE also describes alternating current field measurement (ACFM) as a surface crack method for conducting materials that can work through coatings.
Do coatings have to be removed?
Usually. The FAA lists removal of finishes and sealant as part preparation for both methods, and notes that paint and other coatings can stop penetrant entering flaws.
Can either method size a crack's depth?
No. Both show where a flaw breaks the surface and how long it is; depth needs ultrasonic methods. See [Conventional UT vs phased array (PAUT) vs time-of-flight diffraction (TOFD)](/library/ut-vs-paut-vs-tofd/).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Inspection/Non Destructive Testing (COMAH technical measures document), including case study 1 · UK Health and Safety Executive (HSE)
  2. 2.Advisory Circular AC 43.13-1B, Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair, Chapter 5: Nondestructive Inspection (NDI) · US Federal Aviation Administration (FAA)
  3. 3.OSHA Technical Manual, Section IV, Chapter 3: Pressure Vessel Guidelines · US Occupational Safety and Health Administration (OSHA)
  4. 4.Penetrant Testing: Basic Processing Steps; Advantages and Disadvantages; Common Uses (NDE-Ed) · Iowa State University, Center for Nondestructive Evaluation
  5. 5.Magnetic Particle Inspection: Introduction; Basic Principles; Magnetic Field Orientation and Flaw Detectability (NDE-Ed) · Iowa State University, Center for Nondestructive Evaluation