Skip to content
Beaconby Winda
FactRegulation, Standards and Compliance · Audit and evidence

What is RAGAGEP (recognized and generally accepted good engineering practice)?

·8 sources

Short answer

RAGAGEP, recognized and generally accepted good engineering practice, is the US process safety benchmark for equipment design, inspection and testing. The Occupational Safety and Health Administration (OSHA) process safety standard, 29 CFR 1910.119, and the Environmental Protection Agency (EPA) Risk Management Program rule both use it. Employers choose the applicable codes, standards or internal practices and document compliance.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

Adopting a recommended practice does not mean picking which of its clauses to follow. In its 2016 enforcement memorandum, OSHA says that when an employer departs from a "shall" statement in the RAGAGEP it has adopted, OSHA presumes a violation, and the employer can then explain why its approach is still good engineering practice 2. Departing from a "should" statement is not presumed a violation, as long as the equipment is still documented as compliant 2. In refinery inspections under a national emphasis program that began in June 2007, OSHA issued many citations tied to RAGAGEP, including insufficient thickness measurements and inspection frequencies that were unacceptable or never set 3.

Where does RAGAGEP appear in the rules?

ProvisionWhat it requires
29 CFR 1910.119(d)(3)(ii)Document that equipment complies with RAGAGEP 1
29 CFR 1910.119(d)(3)(iii)For equipment built to codes no longer in general use, determine and document that it is designed, maintained, inspected, tested and operated safely 1
29 CFR 1910.119(j)(4)(ii)Inspection and test procedures follow RAGAGEP 1
29 CFR 1910.119(j)(4)(iii)Inspection and test frequency follows manufacturers' recommendations and good engineering practice, and tightens when operating experience shows the need 1
40 CFR 68.65(d)(2) and (3); 68.73(d)(2) and (3)The same duties for EPA Program 3 processes 4,6
40 CFR 68.67(c)(10), added in 2024Process hazard analyses address gaps between the codes a process was built to and their current versions 5

In OSHA's reading, the term governs three things: how equipment is designed and maintained, how it is inspected and tested, and how often 2.

What counts as RAGAGEP?

OSHA's memo lists these sources and says they are not ranked 2:

  • Widely adopted codes, such as fire and electrical codes that state and local governments adopt. 2
  • Consensus documents developed under American National Standards Institute (ANSI) due-process rules, such as the ASME B31.3 process piping code. 2
  • Non-consensus documents that an industry widely accepts, such as Chlorine Institute pamphlets. 2
  • Manufacturers' recommendations. 2
  • Internal standards, provided they themselves represent recognized and generally accepted practice. 2

OSHA's 2017 refinery guidance names API 510, API 570 and API 580 as examples of inspection RAGAGEP 3. More than one document can apply: OSHA accepts either API RP 520 Part II or ISO 4126-9 for relief valve installation 2. Mixing selected clauses from several documents may leave hazards uncontrolled, and applying a document outside its intended field, such as an ammonia refrigeration vessel practice in a refinery, can lead to citations 2.

How does OSHA read shall and should in RAGAGEP?

Language in the adopted RAGAGEPOSHA's enforcement position
"Shall", "must", "shall not"The developer's mandatory minimum; a deviation is presumed a violation unless the employer shows its approach is still RAGAGEP
"Should"Following it is presumed acceptable; skipping it is not presumed a violation, but the inspector checks the alternative and the compliance record
"Should not"Treated like "should"
Normative annexExplains how to comply and may hold both "shall" and "should"
Informative annexBackground and references; employers are expected to read it, not to consult every source it cites

Source: OSHA enforcement memorandum, 11 May 2016, which replaced a June 2015 version 2.

Does a new edition apply to existing equipment?

Only if the new edition says so. OSHA states that a more protective update that is not explicitly retroactive does not oblige employers to upgrade, but paragraph (d)(3)(iii) still requires them to determine and document that the equipment operates safely 2. OSHA also tells its inspectors to establish the equipment's age, installation date and modifications, and the edition and date of the RAGAGEP the employer selected 2.

EPA goes further in its guidance. Its frequently asked question, updated 20 April 2026, expects owners to review new and updated RAGAGEP regularly for safety gaps, and says the absence of an incident so far is not a sound reason to set aside updated practice 7. EPA's 2024 amendments wrote this gap check into process hazard analysis at 40 CFR 68.67(c)(10) 5. On 24 February 2026 EPA proposed removing that paragraph while keeping the duty to evaluate gaps under its safety information rules 8. As of 25 October 2026, the eCFR text, up to date as of 22 October 2026, still contains it 5.

Where integrity problems show up

RequirementWhat it means for integrity records or workIn the Library
1910.119(d)(3)(ii), document complianceEquipment files need the selected RAGAGEP, with edition and date, and evidence of compliance; missing documentation is itself citable 2What is mechanical integrity (MI)?
1910.119(j)(4)(ii), inspection proceduresRefinery citations included no procedure fixing the number and location of thickness readings, and rising thickness readings left uninvestigated 3What are condition monitoring locations (CMLs)?
1910.119(j)(4)(iii), frequencyCitations included inspection frequencies never established and corrosion rates never calculated to set intervals 3How are inspection intervals set for vessels, piping and tanks?
1910.119(j)(5), deficienciesEquipment outside limits set by process safety information, RAGAGEP included, is corrected before further use or kept safe in the interim under management of change 2What is fitness-for-service (API 579-1/ASME FFS-1)?
1910.119(d)(3)(iii), older equipmentEquipment built to outdated codes needs a documented case that it is still safe 1,2What is asset life extension?
1910.119(j)(2), written proceduresFailing to follow one's own stricter internal inspection procedures can be cited even when published RAGAGEP is met 2What should an inspection plan contain?

Sources: 29 CFR 1910.119 1; OSHA memorandum, 2016 2; OSHA 3918, 2017 3.

Common questions

Is RAGAGEP the same as a code?
No. A code is one possible source; consensus standards, recommended practices, manufacturers' recommendations and qualified internal standards can also serve. See [Code vs standard vs recommended practice: what is the difference?](/library/code-vs-standard-vs-rp/)
Can a company write its own RAGAGEP?
Yes. OSHA accepts internal standards that represent recognized and generally accepted practice, including ones stricter than published documents, and the employer must still document that its equipment complies.
Is RAGAGEP only an OSHA term?
No. EPA's Risk Management Program rule uses it for Program 3 process safety information and mechanical integrity. See [What is process safety management (PSM)?](/library/process-safety-management/)

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
  2. 2.RAGAGEP in Process Safety Management Enforcement (memorandum to regional administrators) · US Occupational Safety and Health Administration (OSHA) ·
  3. 3.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918-08) · US Occupational Safety and Health Administration (OSHA)
  4. 4.40 CFR 68.65, Process safety information · eCFR, US Office of the Federal Register
  5. 5.40 CFR 68.67, Process hazard analysis · eCFR, US Office of the Federal Register
  6. 6.40 CFR 68.73, Mechanical integrity · eCFR, US Office of the Federal Register
  7. 7.Complying with process safety information (PSI) resulting from new and updated recognized and generally accepted good engineering practices (RAGAGEP) · US Environmental Protection Agency (EPA)
  8. 8.Accidental Release Prevention Requirements: Risk Management Programs Under the Clean Air Act; Common Sense Approach to Chemical Accident Prevention (proposed rule), 91 FR 8970 · US Environmental Protection Agency, via Federal Register (govinfo) ·