San Bruno pipeline rupture (2010): lessons for pipeline integrity
The San Bruno pipeline rupture was the September 9, 2010, failure of a 30-inch gas transmission line in San Bruno, California, that killed eight people. The National Transportation Safety Board (NTSB) traced it to a defective seam weld installed in 1956 and to an integrity management program that never found it.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
The operator's records described the pipe as seamless; investigators found six short pieces, some with partly welded seams, that the records did not show 1. The NTSB found that the integrity management program rested on incomplete and inaccurate pipeline data and ended up using an assessment method that could not detect seam defects 1. The fire destroyed 38 homes and damaged 70 1, and the US pipeline regulator cites the case as a reason for its 2019 rules on records and maximum allowable operating pressure 2.
What happened on September 9, 2010?
The line, known as Line 132, starts at a gas terminal in Milpitas, California 1.
| Date and time | Event |
|---|---|
| 1956 | A relocated section is built from six short pipe pieces, 3.5 to 4.7 feet (1.1 to 1.4 m) long, that met no known specification; the seam flaw would have been visible at installation 1 |
| 1961 and 1970 | California (1961) and federal rules (1970) let older lines skip post-construction pressure tests; the line's maximum allowable operating pressure (MAOP) of 400 psig (about 27.6 bar) rests on its highest operating pressure in the years before 1970, reached in 1968 1 |
| 2005 and 2009 | The line is assessed only by external corrosion direct assessment; no in-line inspection had ever been run 1 |
| September 9, 2:46 p.m. | The Milpitas terminal starts the work clearance for replacing its backup power supply 1 |
| 5:22 p.m. | With erratic power and false signals, the pressure regulating valves open fully; outgoing pressure peaks at 396 psig before backup monitor valves hold it near their 386 psig setting 1 |
| About 6:11 p.m. | The pipe ruptures with line pressure near 386 psig; the gas ignites almost at once, leaving a crater about 72 by 26 feet (22 by 8 m) 1 |
| 7:46 p.m. | Mechanics close the last valves by hand; the rupture is isolated 95 minutes after it began 1 |
| August 30, 2011 | The NTSB adopts its report 1 |
Sources: NTSB/PAR-11/01, 2011 1.
Why did the pipe rupture?
The NTSB found that the fracture started in the partly welded long seam of one short piece, which ductile and fatigue crack growth had weakened until it failed under gas pressure 1. The pressure that evening stayed within the MAOP and would not have harmed properly built pipe; corrosion, earthquakes and direct damage by third parties were ruled out 1. In its probable cause, the NTSB named poor quality control in 1956 and an integrity management program that failed to detect and remove the defective pipe 1.
The records gap ran deep. The geographic information system listed the segment as seamless pipe of one grade, but seamless pipe was not made in diameters above 26 inches, the purchase records pointed to a different grade, and the short pieces were not recorded at all 1. Previously identified seam weld cracks and the design and materials of the line were left out of the risk assessment, and the only method used, direct assessment for external corrosion, examines selected spots for the threats an operator is looking for 1. The NTSB found that a hydrostatic pressure test, which the exemption for older lines avoided, would likely have exposed the defect 1.
What did the NTSB recommend?
The recommendations below are the NTSB's, issued to the operator, to the federal regulator and to the state of California 1:
- To the operator (urgent, January 3, 2011). Search for records that are traceable, verifiable and complete for untested lines in populated areas, set MAOP from the weakest section, and where records fall short, run a spike test followed by a hydrostatic test 1.
- To the Pipeline and Hazardous Materials Safety Administration (PHMSA). Remove the exemption for pre-1970 lines and require a hydrostatic test with a spike test; treat manufacturing and construction defects as stable only after a test to 1.25 times MAOP; make all gas transmission lines able to take in-line inspection tools; where a line runs through high consequence areas or class 3 and 4 locations, require valves that close automatically or can be shut remotely; and require control rooms to call 911 at once 1.
- To California. Give the state's pipeline safety division direct enforcement powers and audit the operator's whole system 1.
What changed afterwards?
- The law. The Pipeline Safety, Regulatory Certainty, and Job Creation Act of 2011, enacted January 3, 2012, required verification of the records used to set MAOP and testing of untested lines or lines without accurate records 2.
- Records rule. A PHMSA rule of October 1, 2019, which PHMSA links to San Bruno and the NTSB recommendations, added 49 CFR 192.607: where it applies, records of each pipe's diameter, wall thickness, seam type and grade must be traceable, verifiable and complete and kept for the life of the line, and missing ones must be established by testing 2,4.
- MAOP reconfirmation. The same rule added 49 CFR 192.624 for onshore steel transmission lines in high consequence areas or class 3 and 4 locations (and some moderate consequence areas) whose MAOP records fall short or whose MAOP rests on the historical-pressure exemption. As of October 2026, operators must reconfirm MAOP on 50% of that mileage by July 3, 2028, and on all of it by July 2, 2035 3.
- Valves. A 2022 rule requires rupture-mitigation valves on most new or fully replaced gas and liquid lines 6 inches or larger and immediate 911 calls on a suspected rupture, citing San Bruno and NTSB recommendations P-11-10 and P-11-11 5.
Where integrity problems show up
| Element or step | Integrity link | In the Library |
|---|---|---|
| Records of pipe attributes | Seam type, grade and the short pieces were wrong or missing in the records 1; such records must now be traceable, verifiable and complete for the life of the line 4 | What is material traceability? |
| Basis for MAOP | MAOP came from 1968 operating history, not a pressure test 1 | Maximum allowable operating pressure |
| Pressure testing | A hydrostatic test would likely have exposed the defect 1 | What is a hydrostatic test? |
| Choosing the assessment method | External corrosion direct assessment cannot find seam defects it is not looking for 1 | What is direct assessment (ECDA, ICDA, SCCDA)? |
| In-line inspection capability | The operator told the NTSB that bends, valves and diameter changes made in-line inspection impracticable 1 | What is in-line inspection (ILI) and pigging? |
| Isolation valves | Manual valves took 95 minutes to close 1; new and replaced lines now need rupture-mitigation valves 5 | What are the PHMSA pipeline safety regulations (49 CFR 192 and 195)? |
Sources: NTSB/PAR-11/01, 2011 1; 49 CFR 192.607 4; 87 FR 20940, 2022 5.
Common questions
- Was corrosion the cause?
- No. The NTSB ruled out corrosion; the failure began at a defective seam weld made before the pipe went into service.
- Did the pressure exceed the limit?
- No. Pressure rose during the terminal power work but stayed within the line's MAOP, which the NTSB found would not have endangered properly built pipe.
- How does this relate to the PHMSA mega rule?
- The 2019 MAOP reconfirmation rule, which cites San Bruno, was the first final rule PHMSA issued from its April 2016 gas pipeline proposal, with more rules planned to follow. See [What is the PHMSA gas transmission mega rule?](/library/phmsa-gas-transmission-rule/).
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Pacific Gas and Electric Company Natural Gas Transmission Pipeline Rupture and Fire, San Bruno, California, September 9, 2010 (Pipeline Accident Report NTSB/PAR-11/01) · US National Transportation Safety Board (NTSB) ·
- 2.Pipeline Safety: Safety of Gas Transmission Pipelines: MAOP Reconfirmation, Expansion of Assessment Requirements, and Other Related Amendments, 84 FR 52180 · US Pipeline and Hazardous Materials Safety Administration (PHMSA), via Federal Register (govinfo) ·
- 3.49 CFR 192.624, Maximum allowable operating pressure reconfirmation: Onshore steel transmission pipelines · eCFR, US Office of the Federal Register
- 4.49 CFR 192.607, Verification of pipeline material properties and attributes: Onshore steel transmission pipelines · eCFR, US Office of the Federal Register
- 5.Pipeline Safety: Requirement of Valve Installation and Minimum Rupture Detection Standards, 87 FR 20940 · US Pipeline and Hazardous Materials Safety Administration (PHMSA), via Federal Register (govinfo) ·