What does the Alberta Energy Regulator require for pipelines?
The Alberta Energy Regulator (AER) licenses provincial pipelines in Alberta under the Pipeline Act and the Pipeline Rules (Alberta Regulation 125/2023). The Rules make CSA Z662 the minimum technical standard and require a safety and loss management system, an integrity management program, pressure-test records and prompt incident reports. Directive 077 adds detailed requirements.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
Internal corrosion caused 38% of the 229 pipeline leaks and ruptures in Alberta in 2025, more than any other type of failure, and 77% of those internal corrosion failures were on uncoated steel pipe 1. Steel makes up about 85% of the pipelines the AER licenses, and the AER says confirming that companies run effective programs to monitor and prevent corrosion is the focus of its pipeline inspections and assessments 1. The Pipeline Rules make such a program, and the records behind it, a licence obligation 5.
What does the AER regulate?
- Pipelines within Alberta. High-pressure oil and gas lines that run entirely within Alberta fall under the AER, and handles incidents and inspections for gas utility pipelines on behalf of the Alberta Utilities Commission (AUC); the Canada Energy Regulator (CER) typically regulates lines that cross provincial or national borders 2.
- A large, mostly small-diameter inventory. Alberta had 450,750 km of pipelines in 2025, 955 companies operated AER-regulated lines, and most lines were 6 inches (NPS 6) or smaller 3.
- Many inactive lines. As of 2025, about 42% of AER-regulated pipelines were discontinued or abandoned 3.
- Falling incident rates. There were 277 incidents in 2025, or 0.61 per 1,000 km, against 1.05 per 1,000 km in 2016 2.
Which rules apply to Alberta pipelines?
| Instrument | Status as of 25 October 2026 | Role |
|---|---|---|
| Pipeline Act | In force | Enables pipeline licensing and lets the AER set technical requirements in the Pipeline Rules 4 |
| Pipeline Rules, Alberta Regulation 125/2023 | In force since 15 November 2023, replacing AR 91/2005; revised version effective 29 October 2025; consolidation current to 2 February 2026; set to expire 31 January 2031 unless re-made | Technical requirements from licensing to removal 4,5 |
| Directive 077 | Edition released and effective 2 July 2026, replacing the 15 November 2023 edition | Testing and operating requirements, including temporary pipelines 6,7 |
| CSA Z662 | Named in s. 18 of the Pipeline Rules | Minimum requirements unless the Rules say otherwise 5 |
In Directive 077, "must" marks a requirement, while "should", "recommends" and "expects" mark recommended practice 6.
What do the Pipeline Rules require over a pipeline's life?
| Stage | Requirement | Section |
|---|---|---|
| Design and materials | Z662 sets the minimum; other materials or methods need an engineering assessment and AER approval | 18, 19 |
| Access for inspection | New lines must pass maintenance, inspection and purging pigs where the integrity program or Z662 calls for pigging, and must be reassessed when conditions change | 21 |
| Pressure testing | A continuous, legible record with start and end times, a pipe temperature trace, the location, and the licence and segment numbers, made with calibrated instruments | 36 |
| Operation | A safety and loss management system to Annex A of Z662 and an integrity management program to Annex N, both covering abandoned, temporary surface and inactive lines | 14, 15 |
| Records | Design-to-decommissioning records kept as Z662 requires, given to the AER on request and passed to any buyer | 12, 13 |
| Leaks, breaks and contact damage | Immediate report; on request, a written report on causes and prevention; a record kept in the integrity program and management system | 67 |
| Inactive lines | After 24 months without flow, the licensee must return the line to active service or else discontinue or abandon it | 71 |
Source: Pipeline Rules, AR 125/2023 5.
What does Directive 077 add?
- Insulated pipelines. Common insulation is not counted as an effective corrosion coating, so new insulated lines and modified ones need a coating that meets Clause 9 of Z662. An exemption needs an engineering assessment and integrity measures for corrosion and stress corrosion cracking under wet insulation 6.
- Overpressure protection on artificial lift. Where lift equipment can exceed the licensed maximum operating pressure, the licensee uses two independent protection devices, or one device tested monthly and checked yearly by a certified technician. A defective device stops operation, and inspection logs are kept and shown to the AER on request 6.
- Other topics. Pressure testing with liquids other than fresh water or with gas, temporary surface pipelines, and elevated-temperature pipelines 6.
How does the AER check compliance?
The AER inspects construction, reviews every pipeline incident to check the cause the company found and its compliance, investigates incidents, and looks for gaps in management systems and integrity programs 8. After an incident, the licensee must identify the causes and the gaps in its integrity program and fix them 1. Recurring problems lead to bulletins, such as Bulletin 2016-22 on leak detection, 2019-28 on earth movement, 2021-36 on stress corrosion cracking of hot aboveground carbon steel lines, and 2023-30 on companies hitting their own pipelines 8.
Where integrity problems show up
| Requirement | What it means for integrity records or work | In the Library |
|---|---|---|
| s. 15, program covers inactive lines | With about 42% of AER-regulated lines discontinued or abandoned in 2025, much of the program covers pipe that is not flowing 3,5 | What is pipeline integrity management? |
| s. 72, dead legs | A dead leg still exposed to operating conditions is managed as operating pipe 5 | Dead leg |
| Failure causes reported to the AER | In 2025, 39% of internal corrosion failures involved several mechanisms together, under-deposit corrosion 19% and microbiologically influenced corrosion 7% 1 | What is under-deposit corrosion? |
| Directive 077, s. 2, insulated lines | Exempted lines need integrity measures to monitor corrosion and cracking under insulation 6 | What is corrosion under insulation (CUI)? |
| Bulletin 2021-36 | Licensees were asked to assess susceptibility, inspect at-risk lines, repair defects and review leak detection 8 | What is stress corrosion cracking (SCC)? |
| s. 13, records on transfer | If records are lost, damaged or incomplete, the buyer must show by engineering assessment that the line is fit for service 5 | What does a technical due diligence check in an asset acquisition? |
Sources: AER, Industry Performance Metrics, 2026 1; AER, About Pipelines, 2026 3; AR 125/2023 5; Directive 077, July 2026 6; AER, Improving Pipeline Performance, 2026 8.
Common questions
- Does the AER regulate pipelines that cross into another province?
- Typically not. The CER usually regulates pipelines that cross provincial or international borders, and the AER does not collect data on them. See What do the Canada Energy Regulator onshore pipeline regulations require?
- Are the "should" statements in Directive 077 mandatory?
- No. The directive marks requirements with "must"; "should", "recommends" and "expects" signal recommended practice. See Code vs standard vs recommended practice: what is the difference?
- How does a safety and loss management system differ from an integrity management program?
- The safety and loss management system is the wider set of company policies and processes for managing operating risk; the AER lists the integrity management program as one of its elements, alongside risk management, operating and maintenance procedures and policies on data retention and training.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Industry Performance Metrics (pipeline performance) · Alberta Energy Regulator (AER) ·
- 2.Pipeline Performance · Alberta Energy Regulator (AER) ·
- 3.About Pipelines · Alberta Energy Regulator (AER) ·
- 4.Bulletin 2025-36: Release of Revised Pipeline Rules · Alberta Energy Regulator (AER) ·
- 5.Pipeline Rules, Alberta Regulation 125/2023 (office consolidation, with amendments up to AR 8/2026) · Alberta King's Printer
- 6.Directive 077: Pipelines, Requirements and Reference Tools · Alberta Energy Regulator (AER)
- 7.Bulletin 2026-26: New Edition of Directive 077 · Alberta Energy Regulator (AER) ·
- 8.Improving Pipeline Performance · Alberta Energy Regulator (AER) ·