Skip to content
Beaconby Winda
FactOil, Gas and Chemicals Basics · Facilities and processes

What is fluid catalytic cracking (FCC)?

·10 sources

Short answer

Fluid catalytic cracking (FCC) is a refinery process that cracks heavy gas oil into gasoline and light olefins on a hot, powdered catalyst. The catalyst flows like a fluid between a riser, where cracking takes seconds, and a regenerator, where burning off the coke left on it reheats it. The unit adds no hydrogen.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

What does an FCC unit do?

An FCC unit converts gas oils that boil between about 650 and 1,000 °F (340 and 540 °C) into lighter, higher-value products. Its feed comes from the atmospheric and vacuum distillation columns, the coker and the deasphalter, according to the US Environmental Protection Agency 2. Unlike distillation, which only separates molecules, FCC breaks them, so the US Energy Information Administration (EIA) classes it as a chemical process 1.

FCC is a carbon rejection process: instead of adding hydrogen, it lays carbon down on the catalyst as coke and burns it off for heat 4. The first commercial unit started in 1942, and zeolite Y has been the main cracking ingredient of FCC catalyst since 1964. At the start of 2014, FCC units ran in over 300 of the world's 646 refineries 5.

How do the riser, reactor and regenerator work together?

StepWhat happensTypical conditions
1. RiserHot regenerated catalyst meets preheated feed and steam at the bottom of a vertical pipe; the oil vaporizes and cracks as both travel upwardReaction at about 880 to 980 °F (470 to 525 °C) 2; contact time of seconds 4
2. Reactor and cyclonesCyclones at the top separate catalyst from the cracked vapor, which goes to the main fractionatorPressure about 1.5 to 3 atmospheres 3
3. StripperSteam strips hydrocarbons from the coked ("spent") catalystSteam stripping as the catalyst leaves the reactor 2
4. RegeneratorAir burns the coke off the catalyst, heating itAbout 1,100 to 1,250 °F (590 to 675 °C) 2, with catalyst reaching about 760 °C (1,400 °F) 5
5. ReturnHot catalyst flows back to the riser through a standpipe and slide valveCatalyst-to-oil ratio about 5.5 at the riser bottom 5

The loop runs in heat balance: the heat released by burning coke in the regenerator supplies the heat the cracking reactions absorb 3. The catalyst is a fine powder averaging about 60 to 75 micrometers, made of zeolite, an active matrix, filler and binder 4. Regenerator flue gas passes through cyclones and then an electrostatic precipitator or wet scrubber to remove catalyst fines, and a carbon monoxide boiler can recover more heat 2.

What does an FCC unit produce?

ProductTypical next step
Fuel gas (mostly methane and ethane)Refinery fuel system
Propane and propylene, butane and butylenesSeparated; propylene can go to petrochemical plants, and butylenes to alkylation
FCC gasolineDesulfurized, then blended into gasoline
Light cycle oilHydrotreated or hydrocracked into diesel or heating oil blendstock
Heavy cycle oilHydrocracker or coker
Clarified slurry (decant) oilResidual fuel oil, coker feed, or feed for carbon black and needle coke

Sources: EIA (2012) 1; Penn State FSC 432 course (undated) 4.

Gasoline is the main product, with a selectivity of around 50%, while propylene is typically under 5% of the yield in normal operation; additives based on the zeolite ZSM-5 are used to raise it 5. Even so, the International Energy Agency (IEA) notes that refineries supply propylene in large quantities as an FCC byproduct, and that FCC and catalytic reforming units are the source of most benzene, toluene and xylene aromatics 6.

How is FCC different from hydrocracking?

Both crack heavy gas oil, but they take opposite routes. FCC rejects carbon as coke, runs at low pressure, uses no hydrogen and leans toward gasoline; a hydrocracker adds hydrogen at high pressure and leans toward diesel and jet fuel 4,3. The two are often linked: FCC light cycle oil can be hydrotreated or hydrocracked into diesel blendstock 1,4. See What is hydroprocessing?.

Where integrity problems show up

Unit / equipmentTypical integrity issueIn the Library
Spent and regenerated catalyst slide valves, standpipesErosion of valve internals by abrasive circulating catalystCorrosion vs erosion
Main fractionator overhead and gas recovery sectionWet sour corrosion, cracking and hydrogen blistering when feed nitrogen forms cyanidesWet hydrogen sulfide damage, Hydrogen blistering
Older gas recovery absorbers built from low-toughness steelBrittle fracture into fragments during an explosionBrittle fracture
Regenerator and flue gas system in austenitic stainless steelPolythionic acid stress corrosion cracking, mostly around shutdowns and start-ups; reported as relatively rarePolythionic acid stress corrosion cracking

Sources: US Chemical Safety and Hazard Investigation Board (CSB) reports on Torrance (2017) 8 and Superior (2022) 9; Occupational Safety and Health Administration (OSHA) Technical Manual, Section IV, Chapter 2 (undated) 7; American Fuel & Petrochemical Manufacturers, Q&A question 86 (undated) 10.

At Torrance in 2015, the spent catalyst slide valve had lost about 16 square inches of its internals to erosion over six years and could not seal; that was one of several factors that let hydrocarbons reach the electrostatic precipitator, where they ignited 8. At Superior in 2018, a closed but eroded slide valve let air flow from the regenerator into the reactor, and two absorber vessels made of older steel grades shattered, throwing more than 100 metal fragments across the refinery 9. The CSB notes that some erosion from flowing catalyst is expected over a slide valve's life, so catalyst-facing parts are usually protected with erosion-resistant material, and that refineries typically inspect slide valves at turnarounds every 4 to 6 years 9.

Common questions

Is FCC the same as steam cracking?
No. FCC uses a catalyst to make mainly gasoline from gas oil, while a steam cracker in a petrochemical plant heats feeds such as ethane or naphtha with steam in furnace coils to make ethylene. See [What is a petrochemical plant?](/library/petrochemical-plant/).
Where does an FCC unit get its reaction heat?
Mostly from burning coke off the catalyst in the regenerator; the hot catalyst carries that heat back to the riser, while a process heater preheats the fresh feed (DOE, 2006; EPA, 2015).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Fluid catalytic cracking is an important step in producing gasoline · U.S. Energy Information Administration, Today in Energy ·
  2. 2.AP-42, Section 5.1: Petroleum Refining · U.S. Environmental Protection Agency
  3. 3.Energy Bandwidth for Petroleum Refining Processes · U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)
  4. 4.FSC 432 Petroleum Refining: Fluid Catalytic Cracking (FCC) · Penn State College of Earth and Mineral Sciences (S. Eser)
  5. 5.Fluid catalytic cracking: recent developments on the grand old lady of zeolite catalysis (E. T. C. Vogt, B. M. Weckhuysen), Chemical Society Reviews 44, 7342 to 7370 · Royal Society of Chemistry
  6. 6.The Future of Petrochemicals · International Energy Agency ·
  7. 7.OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes · Occupational Safety and Health Administration
  8. 8.Investigation Report: ExxonMobil Torrance Refinery Electrostatic Precipitator Explosion, Report No. 2015-02-I-CA · U.S. Chemical Safety and Hazard Investigation Board
  9. 9.Investigation Report: FCC Unit Explosion and Asphalt Fire at Husky Superior Refinery, Report No. 2018-02-I-WI · U.S. Chemical Safety and Hazard Investigation Board ·
  10. 10.Q&A Question 86: polythionic acid stress corrosion cracking in FCC regenerator and flue gas systems · American Fuel & Petrochemical Manufacturers