What is a petrochemical plant?
A petrochemical plant turns hydrocarbon feeds such as ethane, propane and naphtha into basic chemicals like ethylene, propylene and aromatics. For olefins, the core unit is a steam cracker, which heats the feed with steam in furnace coils to about 1,400 to 1,600 °F (760 to 870 °C); downstream units turn the products into plastics and other chemicals.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
What does a petrochemical plant make?
The International Energy Agency (IEA) counts as petrochemicals any chemicals derived from natural gas or from oil-based feeds like naphtha and ethane; on that basis they account for 90% of the feedstock used in chemical production 1. In 2017, petrochemical feedstock took about 12% of global oil demand 1.
| Basic chemical | Main production routes | Typical uses |
|---|---|---|
| Ethylene | Steam cracking, almost exclusively | Plastics (largest derivative: polyethylene), antifreeze, detergents |
| Propylene | Steam cracking; refinery fluid catalytic cracking; propane dehydrogenation | Plastics (largest derivative: polypropylene) |
| Butadiene | Byproduct of cracking butane and liquid feeds | Synthetic rubber |
| Benzene, toluene and xylenes (BTX) | Steam cracking; refinery fluid catalytic cracking and catalytic reforming | Intermediates for plastics, fibers and rubber |
| Ammonia and methanol | Steam reforming of natural gas | Fertilizer; formaldehyde and other chemicals |
Sources: IEA (2018) 1; US Energy Information Administration (EIA), Uses of hydrocarbon gas liquids (2023) 6; US Department of Energy (DOE), Chemical Bandwidth Study (2006) 4.
The IEA groups ethylene, propylene and BTX as "high-value chemicals" and, with ammonia and methanol, calls them primary chemicals. World ethylene and propylene output was about 255 million tonnes a year at the time of its 2018 report 1.
How does a steam cracker work?
| Section | What happens |
|---|---|
| 1. Pyrolysis furnaces | Feed mixed with steam flows through coils in a fired furnace at about 1,400 to 1,600 °F (760 to 870 °C) and breaks into smaller molecules, mainly ethylene 3 |
| 2. Quench | A series of quench exchangers cools the hot cracked gas 4 |
| 3. Primary fractionation | Heavier products such as pyrolysis gasoline are separated from the gas 5,1 |
| 4. Compression and acid gas removal | The cracked gas is compressed in stages with cooling in between, and acid gases are removed 4 |
| 5. Chilled separation | A demethanizer, deethanizer and ethylene/ethane splitter separate the products, using refrigeration loops of methane, ethylene and propylene 4 |
| 6. Fuel and flare | Methane and hydrogen are mostly burned as fuel inside the plant; every ethylene site has a flare for excess gas, according to the US Environmental Protection Agency 2 |
The furnaces are the energy core: DOE estimated that about half the energy used to make ethylene goes into the pyrolysis furnace, and it ranks steam cracking as the most energy-intensive chemical process 3,5. Coke forms on the inside of the coils as the furnace runs, insulating them, so firing must rise until the tube wall temperature or pressure drop reaches its limit. The furnace is then taken out of service and decoked with hot air and steam; DOE put the interval between decokes at about 15 to 90 days, varying by furnace 3.
Which feedstocks do steam crackers use?
In the United States, most ethylene comes from cracking ethane, propane or naphtha, with some butane and gas oil, and most plants use more than one feed 2. The choice changes the product slate: an ethane cracker gives about 50% more high-value chemicals than a naphtha cracker, but the output is mostly ethylene, while naphtha gives a more even split of ethylene, propylene and aromatics 1.
Ethane comes from natural gas processing and is hard to move except by dedicated pipeline 6. Naphtha usually comes from refineries, which also supply propylene from their fluid catalytic crackers and aromatics from catalytic reformers 1. See Refining vs petrochemicals: how do they connect?.
What happens to ethylene, propylene and aromatics downstream?
Olefins go mostly into plastics and resins, and also into glues, solvents and coatings 6. Typical conversion routes listed by DOE (2006) include:
- Ethylene to vinyl chloride: ethylene is chlorinated or oxychlorinated to ethylene dichloride, which is then dehydrochlorinated to vinyl chloride 2,4.
- Ethylene to ethylene glycol: ethylene is oxidized to ethylene oxide, which is hydrolyzed to the glycol. 6
- Ethylene and benzene to styrene: benzene is alkylated with ethylene to ethylbenzene, which is dehydrogenated to styrene. 6
- Propylene and benzene to phenol: the pair makes cumene, which is converted to phenol and acetone. 6
- Propylene to acrylonitrile: propylene reacts with ammonia and air (ammoxidation). 6
- Para-xylene to terephthalic acid: liquid-phase oxidation. 6
Where integrity problems show up
| Unit / equipment | Typical integrity issue | In the Library |
|---|---|---|
| Pyrolysis furnace radiant coils and fittings | Coke buildup and carburization that leave tubes brittle; DOE reported replacement every 2 to 7 years | Carburization |
| Cast alloy radiant tubes | Creep growth of the tubes at furnace temperature | Creep |
| Butadiene and other reactive monomer piping | Dead legs where popcorn polymer can grow until the pipe ruptures | Dead leg |
| Carbon steel in hot, high-pressure hydrogen service | High temperature hydrogen attack (HTHA) | High temperature hydrogen attack |
Sources: DOE (2004) 3; Hendrix Group conference paper indexed by the DOE Office of Scientific and Technical Information (OSTI record 352590) 7; US Chemical Safety and Hazard Investigation Board (CSB) news release on Port Neches (2022) 8 and HTHA safety alert (2016) 9.
At Port Neches, Texas, on 27 November 2019, a pump that had been out of service for months left a dead leg in butadiene piping; popcorn polymer built up in it and ruptured the pipe, and the released butadiene ignited. The fires burned for more than a month and injured two employees and a security contractor 8. For hot hydrogen service, American Petroleum Institute Recommended Practice 941 (API RP 941) covers steels in both refineries and petrochemical plants, and the CSB found that HTHA has occurred in conditions its carbon steel curve rated as safe 9.
Common questions
- Is a petrochemical plant the same as a refinery?
- No. A refinery makes mostly fuels from crude oil, while a petrochemical plant makes chemical building blocks, often from refinery naphtha or from ethane. Steam crackers are often built at the same hub as refineries to share feeds, hydrogen and utilities (IEA, 2018).
- Is a steam cracker the same as a fluid catalytic cracker?
- No. A conventional steam cracker uses heat and steam without a catalyst to make mainly ethylene (DOE described catalytic versions as under investigation in 2015), while a refinery's fluid catalytic cracker uses a circulating catalyst to make mainly gasoline. See [What is fluid catalytic cracking (FCC)?](/library/fluid-catalytic-cracking/).
- Do process safety rules apply to petrochemical plants?
- In the United States, the Process Safety Management standard (29 CFR 1910.119) of the Occupational Safety and Health Administration (OSHA) covers, among others, processes that use 10,000 pounds or more of flammable gas on site, according to a 1993 OSHA interpretation letter (OSHA, 1993).
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.The Future of Petrochemicals: Towards more sustainable plastics and fertilisers · International Energy Agency ·
- 2.Technical Support Document for the Petrochemical Production Sector: Proposed Rule for Mandatory Reporting of Greenhouse Gases · U.S. Environmental Protection Agency, Office of Air and Radiation ·
- 3.Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining · U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)
- 4.Chemical Bandwidth Study: Exergy Analysis, Draft Summary Report · U.S. Department of Energy, Industrial Technologies Program
- 5.Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Chemical Manufacturing · U.S. Department of Energy, Advanced Manufacturing Office
- 6.Uses of hydrocarbon gas liquids · U.S. Energy Information Administration ·
- 7.Comparative performance of six cast tube alloys in an ethylene pyrolysis test heater (Hendrix Group Inc.), report no. CONF-980316 · U.S. Department of Energy, Office of Scientific and Technical Information (record)
- 8.CSB Releases Final TPC Report · U.S. Chemical Safety and Hazard Investigation Board ·
- 9.Safety Alert: Preventing High Temperature Hydrogen Attack (HTHA) · U.S. Chemical Safety and Hazard Investigation Board