Refining vs petrochemicals: how do they connect?
Refining turns crude oil mainly into fuels, while petrochemical plants turn hydrocarbons such as naphtha, ethane and propane into chemical building blocks. The two connect through shared streams: refineries supply naphtha, propylene from fluid catalytic crackers and aromatics from catalytic reformers, and steam crackers can send hydrogen and pyrolysis gasoline back.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Refining vs petrochemicals at a glance
| Refining | Petrochemicals | |
|---|---|---|
| Main input | Crude oil, plus some condensate, natural gas liquids and unfinished oils 3 | Naphtha, ethane, propane, butane and gas oil; natural gas for ammonia and methanol 6,1 |
| Main output | Fuels: in 2023, US refineries made about 19.6 gallons of gasoline, 12.5 of distillate and 4.4 of jet fuel per 42-gallon barrel 3 | Ethylene, propylene, butadiene, benzene, toluene and xylenes, then polymers and other intermediates 1 |
| Core processes | Distillation, cracking, reforming, alkylation, hydrotreating, blending 2 | Steam cracking, chilled separation, chemical conversion 8 |
| Typical process temperatures | Crude heater outlet about 650 to 750 °F (343 to 400 °C) 8; fluid catalytic cracker regenerator about 1,100 to 1,250 °F (590 to 675 °C) 9 | Cracking furnace coils about 1,400 to 1,600 °F (760 to 870 °C) 7 |
| Hydrogen balance | Net user: hydrotreating takes about 200 to 800 standard cubic feet per barrel treated, more than the reformer supplies 8,9 | Steam crackers make byproduct hydrogen that can go to refineries 1 |
| Main integrity drivers | Sulfur, chlorides and organic acids in crude; hot hydrogen 15,10,11 | Coke and carbon in furnace coils; reactive monomers in dead legs 7,12 |
| US process safety rule | Occupational Safety and Health Administration (OSHA) Process Safety Management standard (29 CFR 1910.119), with a refinery National Emphasis Program since 2007 13 | Same standard; it covers, among others, processes with 10,000 pounds or more of flammable gas on site 14 |
When is refining used?
- To make fuels from crude at scale. Gasoline, diesel and jet fuel make up most of a US refinery's output 3.
- To upgrade the heavy part of the barrel. Conversion units crack heavy fractions into lighter, higher-value ones 2.
- To meet product specifications. Hydrotreaters remove sulfur and nitrogen from jet fuel and diesel 8.
- To supply some chemical feedstock. In 2023, each US barrel yielded about 0.34 gallons of naphtha and 0.21 gallons of other oils for petrochemical feedstock 3, and refinery olefins such as propylene and butylenes are also sold as feedstock 4.
When is petrochemical processing used?
- To make ethylene. Ethylene comes almost exclusively from steam crackers in the chemical sector 1.
- To make the building blocks of plastics, fibers and rubber. Demand for ethylene, propylene and aromatics follows those markets 1.
- To use cheap light feeds. An ethane cracker yields about 50% more high-value chemicals than a naphtha cracker, though mostly ethylene; naphtha gives more propylene and aromatics 1.
- To make ammonia and methanol. These come mainly from steam reforming of natural gas 1.
In 2017, petrochemical feedstock accounted for about 12% of global oil demand 1. See What is a petrochemical plant?.
Which streams connect a refinery and a petrochemical plant?
| Stream | From | To | Source |
|---|---|---|---|
| Naphtha | Refinery crude unit | Naphtha steam cracker | 1 |
| Propane and butanes | Refineries (for example, from the fluid catalytic cracker) and natural gas plants | Steam crackers | 5,4,6 |
| Ethane | Natural gas processing plants, not refineries | Ethane steam crackers | 4 |
| Propylene and butylenes | Refinery fluid catalytic cracker | Polymer and chemical units | 5,1 |
| Benzene, toluene and xylenes | Refinery fluid catalytic cracker and catalytic reformer | Aromatics and chemical units | 1 |
| Hydrogen | Steam cracker | Refinery hydrotreaters | 1 |
| Pyrolysis gasoline | Steam cracker | Refinery, for processing into gasoline components | 1 |
The catalytic reformer makes aromatics by stripping hydrogen from naphthenes in naphtha, and that hydrogen goes to the hydrotreaters; refineries still usually need a steam methane reformer or bought hydrogen to cover demand 9,1. Because of these links, steam crackers are often built in the same industrial hub as refineries, even under different owners, to share feeds, utilities and logistics 1. At the time of the International Energy Agency's 2018 report, about 40% of European naphtha cracking capacity sat inside integrated refinery and petrochemical complexes, against less than 20% of US naphtha cracking capacity 1.
Where integrity problems show up
| Side | Unit / equipment | Typical integrity issue | In the Library |
|---|---|---|---|
| Refinery | Hot crude unit piping and heater tubes | Sulfidation; the US Chemical Safety and Hazard Investigation Board (CSB) states it is present at every refinery that runs crude | Sulfidation |
| Refinery | Crude unit overhead | Hydrochloric acid and ammonium chloride corrosion | Hydrochloric acid corrosion, Ammonium chloride corrosion |
| Both | Carbon steel in hot, high-pressure hydrogen service (for example, refinery hydrotreaters) | High temperature hydrogen attack; American Petroleum Institute Recommended Practice 941 (API RP 941) covers hydrogen service in both refineries and petrochemical plants | High temperature hydrogen attack |
| Petrochemical | Cracking furnace coils | Coke buildup and carburization; the US Department of Energy (DOE) reported coil replacement every 2 to 7 years | Carburization |
| Petrochemical | Butadiene piping | Popcorn polymer growing in dead legs until the pipe ruptures | Dead leg |
Sources: CSB: Richmond final report (2015) 10, high temperature hydrogen attack safety alert (2016) 11, Port Neches news release (2022) 12; DOE (2004) 7; OSHA Technical Manual, Section IV, Chapter 2 (undated) 15.
On the refinery side, the mechanisms in the table trace back to compounds that arrive with the crude, such as sulfur, salts and acids 15,10. On the cracker side, they trace back to high coil temperatures and the coke that forms inside the coils 7. Hot hydrogen service appears in both.
Common questions
- Is a petrochemical plant part of a refinery?
- Sometimes. Some sites are integrated refinery and petrochemical complexes, while others are separate plants that buy feed; the IEA notes that ownership of the two is more often separate in the United States than in other regions (IEA, 2018).
- Do refineries make ethylene?
- Most ethylene is made in steam crackers in the chemical sector (IEA, 2018). EPA noted that in the United States some ethylene also comes from cracking and other processes run at refineries (EPA, 2008).
- Is a steam cracker the same as a fluid catalytic cracker?
- No. A steam cracker breaks feeds such as ethane or naphtha with heat and steam to make mainly ethylene, while a fluid catalytic cracker in a refinery uses a circulating catalyst to make mainly gasoline, with propylene as a byproduct (DOE, 2004; EIA, 2012). See [What is fluid catalytic cracking (FCC)?](/library/fluid-catalytic-cracking/).
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.The Future of Petrochemicals: Towards more sustainable plastics and fertilisers · International Energy Agency ·
- 2.Refining crude oil: the refining process · U.S. Energy Information Administration
- 3.Refining crude oil: inputs and outputs · U.S. Energy Information Administration ·
- 4.Uses of hydrocarbon gas liquids · U.S. Energy Information Administration ·
- 5.Fluid catalytic cracking is an important step in producing gasoline · U.S. Energy Information Administration, Today in Energy ·
- 6.Technical Support Document for the Petrochemical Production Sector: Proposed Rule for Mandatory Reporting of Greenhouse Gases · U.S. Environmental Protection Agency, Office of Air and Radiation ·
- 7.Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining · U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)
- 8.Energy Bandwidth for Petroleum Refining Processes · U.S. Department of Energy, Industrial Technologies Program (prepared by Energetics Inc.)
- 9.AP-42, Section 5.1: Petroleum Refining · U.S. Environmental Protection Agency
- 10.Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire, Report No. 2012-03-I-CA · U.S. Chemical Safety and Hazard Investigation Board
- 11.Safety Alert: Preventing High Temperature Hydrogen Attack (HTHA) · U.S. Chemical Safety and Hazard Investigation Board
- 12.CSB Releases Final TPC Report · U.S. Chemical Safety and Hazard Investigation Board ·
- 13.CPL 03-00-004, Petroleum Refinery Process Safety Management National Emphasis Program · Occupational Safety and Health Administration ·
- 14.Standard interpretation: Processes involving flammable liquids and gases (29 CFR 1910.119) · Occupational Safety and Health Administration ·
- 15.OSHA Technical Manual, Section IV, Chapter 2: Petroleum Refining Processes · Occupational Safety and Health Administration