Skip to content
Beaconby Winda
FactEngineering Design and Materials · Engineering documents

What is a piping isometric drawing?

·9 sources

Short answer

A piping isometric drawing shows a run of piping in a three-dimensional view on a flat sheet, with the details and materials needed to build it. Its bill of materials lists each component, and inspectors compare installed piping with it. ISO 6412-2:2017, from the International Organization for Standardization, sets drafting rules for isometric pipeline drawings.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

In the 2019 Philadelphia refinery fire, the piping circuit that failed had 141 condition monitoring locations (CMLs), but none was on the elbow that ruptured 1. The elbow, installed around 1973 at 0.322 inch (about 8.2 mm), had thinned to a minimum of 0.011 inch (about 0.28 mm), while neighboring components lower in nickel and copper had not corroded as fast 1. The US Chemical Safety and Hazard Investigation Board (CSB) found that published guidance at the time did not require every carbon steel component in hydrofluoric acid service to be inspected; the American Petroleum Institute's API RP 751 was later revised to require a special program covering each such component and weld in identified corrosion zones 1.

What does a piping isometric show?

The Capital Facilities Information Handover Specification (CFIHOS) defines the isometric diagram as a construction detail drawing for piping, shown in a three-dimensional isometric view, that gives an accurate bill of materials and material take-off 4. ISO 6412-1:2017 sets the general rules for drawing pipelines in simplified form 3, and ISO 6412-2:2017 adds the rules for isometric representation, which is used to show the essential features clearly in three dimensions 2. Both are second editions, confirmed in 2023 2,3.

How is an isometric different from a P&ID?

Piping and instrumentation diagram (P&ID)Piping isometric
What it showsHow equipment, lines, valves and instruments connect in a unitThe physical route of a run of piping in three dimensions
Scale and layoutA schematic, not to scale and not a layoutA construction drawing of the routed pipe
Component detailEvery valve and instrument by type; pipe size and identificationA bill of materials for the piping components
Main useDesign, hazard review, procedures and operationFabrication, installation and checking what was built

Sources: university process control text 5; CFIHOS document type definitions 4; ISO 6412-2:2017 2; OSHA CPL 03-00-004 6.

How are isometrics used in fabrication and construction?

The bill of materials on each isometric feeds the material take-off and purchasing 4. Piping can be prefabricated in spools, which CFIHOS defines as assemblies of piping components made as one item 4. Design choices made on these drawings carry into operation. At a Texas City, Texas, refinery, three elbows on a hydrogen heat exchanger were made dimensionally identical, which the CSB noted needs fewer fabrication drawings and weld joints, but which let a carbon steel elbow swap places with a low-alloy one during maintenance; it ruptured in 2005 after about three months in high temperature hydrogen service 9.

Before start-up, the US process safety standard requires a check that construction and equipment follow the design specifications 7. Guidance from the Occupational Safety and Health Administration (OSHA) for its refinery inspections suggests comparing the construction of sampled piping circuits with both their isometric drawings and their as-built drawings 6. OSHA's Appendix C adds that as-built drawings and materials of construction should be verified and kept in quality assurance records 7.

How do isometrics support inspection after start-up?

Wall thickness in corrosive piping is measured at predetermined CMLs, and OSHA cites API 570 as calling for them at injection points, mixing points and dead legs, not only along the run 8. For each sampled circuit, OSHA's refinery checks look for the original thickness, the locations, dates and results of later readings, and the retirement thickness 6.

The Philadelphia report shows why component-level detail matters. CMLs for the unit were first set in 1973 on the assumption of uniform corrosion, at representative points; the failed circuit grew from 41 CMLs in 2002 to 141 by 2019, and the CSB drew it as a model showing each CML and its latest reading 1. The elbow's specification called for ASTM A234 grade WPB and it was stamped WPB, but its composition matched a grade with more nickel and copper, which corrodes faster in hydrofluoric acid 1.

Where integrity problems show up

Decision or step at this stageWhat it affects laterIn the Library
The bill of materials specifies each component's material, and look-alike parts differ in materialA wrong part can pass unseen: at Texas City (2005), a carbon steel elbow identical in size to low-alloy ones was swapped in and ruptured after about three months; the CSB noted that designs can prevent such swaps 9What is positive material identification (PMI)?, What is material traceability?
Inspection locations are placed on specific componentsAt Philadelphia (2019), a circuit with 141 CMLs had none on the elbow that ruptured 1What are condition monitoring locations (CMLs)?, What should an inspection plan contain?
Original thickness is recorded at installationOSHA looks for it, with later readings and the retirement thickness, for each sampled circuit 6Baseline inspection, Corrosion rate
Installed piping is checked against isometric and as-built drawingsSupports the pre-startup check that construction follows the design 6,7What are as-built drawings?, What is a pre-startup safety review (PSSR)?

Sources: CSB report on Philadelphia, 2022 1; CSB safety bulletin on Texas City, 2006 9; OSHA CPL 03-00-004, 2007 6; 29 CFR 1910.119 and Appendix C 7.

Common questions

What is the difference between an isometric and a P&ID?
The P&ID is a schematic of how a unit is connected and controlled and is not drawn to scale. The isometric shows the routed pipe and its components for construction. See [What is a piping and instrumentation diagram (P&ID)?](/library/piping-and-instrumentation-diagram/).
What is a pipe spool?
CFIHOS defines a piping spool as an assembly of piping components prefabricated as one item. It also defines a spool piece separately, as a short section of pipe used to connect pipe ends.
What is the difference between an isometric and an as-built drawing?
An isometric is issued for fabrication and installation; an as-built drawing records what was actually installed. OSHA's inspection guidance compares installed piping with both. See [What are as-built drawings?](/library/as-built-drawings/).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Fire and Explosions at Philadelphia Energy Solutions Refinery Hydrofluoric Acid Alkylation Unit, Philadelphia, Pennsylvania (Investigation Report No. 2019-04-I-PA) · US Chemical Safety and Hazard Investigation Board (CSB) ·
  2. 2.ISO 6412-2:2017, Technical product documentation: Simplified representation of pipelines, Part 2: Isometric projection (Edition 2, 2017 (confirmed 2023)) · International Organization for Standardization (ISO)
  3. 3.ISO 6412-1:2017, Technical product documentation: Simplified representation of pipelines, Part 1: General rules and orthogonal representation (Edition 2, 2017 (confirmed 2023)) · International Organization for Standardization (ISO)
  4. 4.CFIHOS Core Reference Data Library (C-ST-001): document types, tag classes (V2.0) · IOGP JIP36, Capital Facilities Information Handover Specification (CFIHOS) ·
  5. 5.Chemical Process Dynamics and Controls, 4.1: P&ID General Information (P. Woolf et al., University of Michigan) · LibreTexts Engineering (CC BY 3.0)
  6. 6.CPL 03-00-004, Petroleum Refinery Process Safety Management National Emphasis Program · US Occupational Safety and Health Administration (OSHA) ·
  7. 7.29 CFR 1910.119, Process safety management of highly hazardous chemicals (including Appendix C) · eCFR, US Office of the Federal Register
  8. 8.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918-08) · US Occupational Safety and Health Administration (OSHA)
  9. 9.Safety Bulletin No. 2005-04-B: BP Texas City, TX Refinery Fire. Positive Material Verification: Prevent Errors During Alloy Steel Systems Maintenance · US Chemical Safety and Hazard Investigation Board (CSB) ·