Skip to content
Beaconby Winda
FactRegulation, Standards and Compliance · Audit and evidence

What is a PSM compliance audit?

·8 sources

Short answer

A process safety management (PSM) compliance audit checks, at least every three years, that a plant's PSM procedures are adequate and followed. Under 29 CFR 1910.119(o), at least one person knowledgeable in the process conducts it; the employer certifies it, responds to each finding, documents corrections and keeps the two latest reports.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

At a Superior, Wisconsin, refinery, PSM compliance audits in 2013 and 2016 had raised concerns about unclear operating procedures with refinery management 1. On 26 April 2018, during a planned shutdown of the fluid catalytic cracking unit, whose procedure still lacked effective safe operating limits, two vessels exploded; 36 workers were injured and sought medical attention, and the US Chemical Safety and Hazard Investigation Board (CSB) put property damage at about $550 million 1. The CSB concluded that the refinery's response to those audit findings had been ineffective 1. The federal rule requires a documented response to each finding and proof that deficiencies were corrected 2.

What does 29 CFR 1910.119(o) require?

ParagraphRequirement in plain words
(o)(1)At least every three years, the employer certifies that it has evaluated compliance with the whole standard, to confirm that procedures and practices are adequate and in use
(o)(2)At least one person knowledgeable in the process conducts the audit
(o)(3)The findings go into a written report
(o)(4)The employer promptly decides and documents a response to each finding, and documents that deficiencies were corrected
(o)(5)The two most recent audit reports are kept

Source: 29 CFR 1910.119, issued by the US Occupational Safety and Health Administration (OSHA) 2. Because the audit covers the whole standard, it reaches every element of the program, from process safety information and hazard analysis to mechanical integrity, management of change and incident investigation 2. See What is process safety management (PSM)?

How is a compliance audit carried out?

OSHA's nonmandatory Appendix C to the standard describes five stages 2:

  1. Planning. Format, staffing, schedule and verification methods are set beforehand, often with a checklist keyed to each paragraph of the standard. 2
  2. Staffing. A trained person or team; a large, complex plant may need process, instrumentation, maintenance, emergency and auditing expertise, led by someone skilled in audit techniques and impartial toward the area audited. 2
  3. Conducting. Document review, inspection of the physical plant and interviews at all levels, with a sample large enough to give confidence in the result. 2
  4. Evaluation and corrective action. Management reviews the findings and sets priorities, timetables and owners; changes go through management of change, and a decision to take no action is recorded with the reason. 2
  5. Follow-up and documentation. A tracking system reports status until each finding is closed. 2

How does the EPA Risk Management Program rule differ?

The Environmental Protection Agency (EPA) rule has a parallel duty for Program 3 processes in 40 CFR 68.79, with the same three-year cycle, knowledgeable auditor, report, documented responses and two retained reports 4. Since EPA's 2024 amendments, the next audit must be a third-party audit after an accidental release that meets the rule's accident-history criteria in 40 CFR 68.42(a), or when the implementing agency requires one 4. Third-party auditors must meet competency and independence criteria, including no employment with the owner for two years after the final report 5.

EPA added third-party audits in 2017, rescinded them in 2019 and reinstated them in 2024; on 24 February 2026 it proposed either removing them or limiting them to facilities with two accidents in five years 6. As of 25 October 2026, the eCFR text, up to date as of 22 October 2026, still contains the 2024 provisions 4,5.

What does an audit check in mechanical integrity?

The mechanical integrity element requires written procedures, trained maintenance staff, inspections and tests that follow RAGAGEP (recognized and generally accepted good engineering practice) at suitable frequencies, a record of each inspection and test, correction of deficiencies, and quality assurance for new equipment and spare parts 2. OSHA's refinery inspections show where gaps were common: missing or inadequate inspection procedures, too few thickness measurements, inspection frequencies never set, inadequately recorded piping inspections, no inspection for corrosion under insulation, and anomalous readings left unresolved 3. See What is mechanical integrity (MI)?

What can a compliance audit miss?

An audit built only to find compliance gaps checks what the rule spells out. The CSB noted that federal rules have no explicit requirement for trainer qualifications or hands-on practice, so such audits may not address them, and pointed to Center for Chemical Process Safety (CCPS) audit guidance on criteria beyond strict compliance 1. At the Superior refinery, the 2016 audit team appeared to have asked only contractors and emergency responders about training, not operators 1. CCPS uses "PSM audit" for an audit of any process safety program, not one done solely to meet OSHA's standard 7.

Where integrity problems show up

RequirementWhat it means for integrity records or workIn the Library
(o)(1), all elements every three yearsInspection records, frequencies and open equipment deficiencies are audited with the rest of the program 2What is mechanical integrity (MI)?
(j)(4)(iv), inspection recordsEach record can be checked for date, inspector, equipment identifier, method and result 2What inspection records do codes require you to keep?
(j)(4)(ii) and (iii), RAGAGEPInspection practice and frequency are judged against the RAGAGEP the employer selected 2,3What is RAGAGEP (recognized and generally accepted good engineering practice)?
(o)(4), documented responseA finding stays open until its correction is documented; at Superior the response to procedure findings was ineffective 1,2Which KPIs measure asset integrity performance?
Appendix C, field inspectionConditions such as uninspected insulated equipment show up in the field, not in files 2,3What is corrosion under insulation (CUI)?
40 CFR 68.79(f), third-party triggerAfter a reportable release, the next audit is a third-party audit, as of 25 October 2026 4What is the EPA Risk Management Program (RMP) rule?
Canada, SOR/99-294 s. 55Federally regulated pipeline companies audit their integrity programs at least every three years 8What do the Canada Energy Regulator onshore pipeline regulations require?

Sources: CSB report 2018-02-I-WI, 2022 1; 29 CFR 1910.119 2; OSHA 3918, 2017 3; 40 CFR 68.79 4; SOR/99-294 8.

Common questions

Is a compliance audit the same as a process hazard analysis revalidation?
No. Process hazard analyses are updated and revalidated at least every five years under paragraph (e)(6), while the compliance audit, at least every three years, covers all elements of the standard. See [What is a hazard and operability study (HAZOP)?](/library/hazop/)
Does the auditor have to be independent?
OSHA's rule requires only at least one person knowledgeable in the process; its nonmandatory appendix says the lead should be impartial toward the area audited. EPA requires an independent third party when its trigger applies, as of 25 October 2026.
How long are audit reports kept?
The two most recent reports, under both OSHA's and EPA's rules.

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.Investigation Report No. 2018-02-I-WI: FCC Unit Explosion and Asphalt Fire at Husky Superior Refinery · US Chemical Safety and Hazard Investigation Board (CSB) ·
  2. 2.29 CFR 1910.119, Process safety management of highly hazardous chemicals (including nonmandatory Appendix C) · eCFR, US Office of the Federal Register
  3. 3.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918-08) · US Occupational Safety and Health Administration (OSHA)
  4. 4.40 CFR 68.79, Compliance audits · eCFR, US Office of the Federal Register
  5. 5.40 CFR 68.80, Third-party audits · eCFR, US Office of the Federal Register
  6. 6.Accidental Release Prevention Requirements: Risk Management Programs Under the Clean Air Act; Common Sense Approach to Chemical Accident Prevention (proposed rule), 91 FR 8970 · US Environmental Protection Agency, via Federal Register (govinfo) ·
  7. 7.PSM audit (Process Safety Glossary) · Center for Chemical Process Safety (CCPS), American Institute of Chemical Engineers
  8. 8.Canadian Energy Regulator Onshore Pipeline Regulations (SOR/99-294) · Justice Laws Website, Government of Canada