Skip to content
Beaconby Winda
FactInspection, Testing and Monitoring · In-service inspection codes

What is API 570?

·9 sources

Short answer

API 570 is the American Petroleum Institute's code for inspecting, rating, repairing and altering metallic piping systems after they enter service. It covers the piping and its pressure-relieving devices and defines the in-service inspection and condition-monitoring program. The current edition is the 5th (February 2024), supported by API RP 574 on inspection practice.

By , Editor·Researched and drafted by ·Checked by , Editor·Last checked ·Next review

Why does it matter?

In June 2019 a pipe elbow ruptured in the hydrofluoric acid alkylation unit of a refinery in Philadelphia, Pennsylvania; installed in 1973 with a 0.322 inch wall, it had thinned to 0.011 inch 4. The circuit around it had grown to 141 condition monitoring locations (CMLs), none of them on that elbow, whose high nickel and copper content made it corrode faster than the pipe on either side 4. The US Chemical Safety and Hazard Investigation Board (CSB) noted that published practice at the time did not require every carbon steel component in that service to be inspected 4.

What does API 570 cover?

  • Designation and edition. API 570, Piping Inspection Code: In-Service Inspection, Rating, Repair, and Alteration of Piping Systems, is in its 5th edition, dated February 2024 1. API announced the 5th editions of API 570 and RP 574 together 2.
  • Scope. It is the code for metal piping once it is operating, along with the relief devices that protect that piping. In the catalog's account it lays down the program for inspecting and monitoring the piping in service and the repair guidance that keeps it sound 1.
  • Companion practice. API RP 574, Inspection Practices for Piping System Components (5th edition, February 2024), backs up the code as a reference for piping inspectors working in refineries and chemical plants 1.
  • Related documents. Relief device inspection is described in API RP 576 (5th edition, 2024), and damaged piping can be evaluated with API 579-1/ASME FFS-1 (4th edition, December 2021), which API lists as referenced by API 570 1.
  • Where it stops. The code applies only after piping has been placed in service 1. For construction rules see What is ASME B31.3 (process piping)?, and for the boundary with transmission lines Piping vs pipeline: what is the difference?.

How is in-service piping inspection organized?

  • Circuits. The CSB explains that refineries divide piping into circuits: runs that see similar process conditions, share a material and are expected to suffer the same damage 4. See What is a corrosion loop?.
  • Condition monitoring locations. Within each circuit, wall thickness is measured at intervals at chosen spots called CMLs; the CSB notes that one CML may hold up to four readings around the pipe, and that CMLs are also called thickness monitoring locations 4. See What are condition monitoring locations (CMLs)?.
  • How many CMLs. In the CSB's description, a circuit expected to corrode evenly gets fewer CMLs and one prone to local attack gets more 4. OSHA's 2017 refinery review adds that CMLs belong at spots where deterioration is likely, such as injection points, mixing points and dead legs, and that their number weighs worker safety, the expected corrosion rate and how complex the system is 5.
  • Timing. OSHA describes measurement frequency as depending on how hazardous the service is, with the interval for a given line set by the inspector or piping engineer within the owner's quality system 5. Timing is covered in How are inspection intervals set for vessels, piping and tanks?; risk-based planning in What is risk-based inspection (RBI)?.

Who requires API 570?

  • US process safety rules. Piping systems, including valves, fall under the mechanical integrity element of OSHA's process safety management standard, which requires inspection to follow good engineering practice 6. OSHA names API 570 as an example of that practice and found piping circuits to be the equipment most often cited for inspection frequencies that did not meet it 5.
  • Offshore production. The Bureau of Safety and Environmental Enforcement (BSEE) requires platform production process piping to be designed, installed, inspected, repaired, tested and maintained to API RP 14E and API 570, incorporating the 4th edition (February 2016) with its 2017 addendum 7.
  • The UK. The Health and Safety Executive (HSE) regards API 570, RP 574 and Energy Institute guidance as relevant good practice for reducing pipework risk at major hazard sites and offshore installations 8.
  • State boiler and pressure vessel law. Colorado, for example, accepts API 570 (4th edition) in place of the National Board Inspection Code for the chemical and petroleum industries 9.

API certifies piping inspectors against API 570 in a program that API states is ANSI-accredited 3. See How do API 510, 570 and 653 inspector certifications work?.

Where integrity problems show up

What it finds wellWhat it can miss or get wrongIn the Library
Thinning at CMLs in circuits where corrosion is even along the line 4A component that corrodes faster than its circuit: the Philadelphia elbow, with no CML, thinned while neighboring components did not 4What are condition monitoring locations (CMLs)?
Dead legs, which HSE notes can corrode faster and need special attention 8A local thin patch between fixed readings: at a UK refinery in 2019, four thickness points on a dead-leg relief line missed the spot that failed, releasing about 75 tonnes of hydrocarbon; HSE judged spot ultrasonic checks inadequate for high-risk dead legs 8Dead leg
Corrosion rate trends built from repeated readings 5OSHA cited sites that did not calculate corrosion rates to set measurement intervals, and rising thickness readings left uninvestigated 5What is an inspection data management system (IDMS)?
Exterior corrosion that routine external inspection can see 5Corrosion hidden under insulation: OSHA cited a sulfur unit whose piping and vessels were not inspected for it 5What is corrosion under insulation (CUI)?

Sources: CSB report on Philadelphia (2022) 4; OSHA 3918 (2017) 5; HSE safety alert CEMHD2-2019 8.

Common questions

What is the difference between API 570 and API RP 574?
API 570 is the code that sets requirements for in-service piping; RP 574 is a recommended practice that supplements it with inspection know-how for piping components. See [Code vs standard vs recommended practice: what is the difference?](/library/code-vs-standard-vs-rp/).
Is API 570 a design code?
No. It applies to piping once in service; design and construction rules come from separate piping codes, described in [What is ASME B31.3 (process piping)?](/library/asme-b31-3/).
Is a CML the same as a TML?
In practice, yes: the CSB notes that condition monitoring locations are also called thickness monitoring locations. See [Thickness measurement location](/glossary/thickness-measurement-location/).

Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.

Sources

  1. 1.2025 Publications Catalog (entries for API 570, RP 574, RP 576 and API 579-1/ASME FFS-1) (API 570, 5th edition, February 2024; RP 574, 5th edition, February 2024; RP 576, 5th edition, 2024; API 579-1/ASME FFS-1, 4th edition, December 2021) · American Petroleum Institute (API)
  2. 2.API Strengthens Piping Inspection Standards with New Updates · American Petroleum Institute (API)
  3. 3.Individual Certification Programs · American Petroleum Institute (API)
  4. 4.Investigation Report: Fire and Explosions at Philadelphia Energy Solutions Refinery Hydrofluoric Acid Alkylation Unit (No. 2019-04-I-PA) · US Chemical Safety and Hazard Investigation Board (CSB) ·
  5. 5.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
  6. 6.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
  7. 7.30 CFR 250.198, Documents incorporated by reference, and 250.841, Platforms · eCFR, US Office of the Federal Register
  8. 8.Catastrophic rupture of dead-leg pipe-work (Safety alert, Bulletin No. CEMHD2-2019) · UK Health and Safety Executive (HSE) ·
  9. 9.NB-370, National Board Synopsis of Boiler and Pressure Vessel Laws, Rules and Regulations (Colorado entry) · National Board of Boiler and Pressure Vessel Inspectors (NBBI)