What is risk-based inspection (RBI)?
Risk-based inspection (RBI) plans inspection of pressure equipment from risk: each item's probability of failure combined with its consequence of failure. The result sets what, where, how and when to inspect. API RP 580 sets out the elements of an RBI program, and API RP 581 gives one quantitative method.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
In June 2019 a pipe elbow in the hydrofluoric acid alkylation unit of a Philadelphia, Pennsylvania, refinery ruptured after thinning to 0.011 inch from an original 0.322 inch 9. The inspection program, set up in 1973, assumed uniform corrosion and monitored representative points; by 2019 the circuit had 141 thickness monitoring locations, none of them on the failed elbow 9. That elbow was rich in nickel and copper and corroded faster than its neighbors, which were not thin 9.
The US Chemical Safety and Hazard Investigation Board (CSB) found that no published industry practice at the time asked refiners to check every carbon steel component in that service. After the fire, the industry's recommended practice for these units was revised to call for a special inspection program covering each such component and weld in the zones where acid corrodes steel 9. The gap between where a program looks and where damage actually runs is the question risk-based inspection (RBI) tries to answer.
What is risk-based inspection?
The Engineering Equipment and Materials Users Association (EEMUA) defines it as building an inspection plan from the asset's operating context, how it may degrade, and the likelihood and consequences of failure over its life 3. CSB summarizes the aim set by the American Petroleum Institute (API): spend inspection effort where it counts by weighing the time between inspections against the risk that known damage mechanisms cause a failure 10.
The idea grew up in the 1990s as a way to make maintenance and safety pull in the same direction, according to a 2026 open-access review by Collina and colleagues, and spread from onshore chemical and petrochemical plants to offshore and energy work 14. The same review sets it beside two older habits. Time-based work happens on a calendar, whatever the condition of the equipment; condition-based work waits for monitoring data to say that something is needed. A risk-based program instead ranks equipment so that the items with the most risk get attention first, which is why it suits plants that handle hazardous substances 14. See Risk-based inspection vs time-based inspection.
How does RBI work?
Public descriptions differ in detail but share one loop. The outline below draws on a 2015 safety study by the National Transportation Safety Board (NTSB) of risk assessment in US gas pipeline programs, and on the 2026 review of risk-based methods in process plants 13,14:
- Name the threats. For each item, list how it could degrade and where, from its material, service and history 13. After the 2012 Richmond, California, refinery fire, CSB recommended that a team of qualified people carry out a documented review of damage mechanisms and their consequences for this purpose 12. See What is a damage mechanism review?.
- Estimate the likelihood. Judge or calculate how likely each threat is to end in a loss of containment over a set period 13,1.
- Estimate the consequence. Work out what a release would do to people, property and the environment; some studies turn this into money 14.
- Combine and rank. Put the two together for each item and sort the items by the result 13,14.
- Test against criteria. Compare each risk with what the operator will accept. The review names as low as reasonably practicable (ALARP) and published acceptance criteria from the Netherlands and the US Environmental Protection Agency (EPA) as examples 14.
- Plan the work. Items that fail the test get inspection or other action. Where the likelihood estimate is good enough, the plan can be worked backward from a target probability of failure, so the inspection lands before the risk target is reached 14,1.
- Inspect and update. Findings go back into the estimate, so the next plan starts from better knowledge of the equipment 1,14.
How is the risk estimated?
Probability of failure (PoF). API describes failure in RP 581 as leakage to the atmosphere or rupture of the pressure boundary 1. The 2026 review lists several ways to put a number on it: fault trees that combine the chances of the events leading to a release, statistical reliability models of a single failure, and Bayesian networks, which can be revised as new evidence comes in. Simpler studies give each scenario a frequency rating instead 14. See Probability of failure.
Consequence of failure (CoF). Quantitative studies model the release itself and then the fire, explosion or toxic exposure it could cause; qualitative ones assign a severity rating 14. In its pipeline study, NTSB found that operators' consequence models were simple compared with their likelihood models 13. See Consequence of failure.
Putting them together. Methods run from judgement to calculation. US gas pipeline rules let operators rely on subject matter experts, relative models that weight and add scores, scenario models built from event or fault trees, or probabilistic models that give an absolute figure, such as expected deaths per mile per year 13. Process plant studies often place each item on a risk matrix, consequence on one axis and likelihood on the other, or multiply likelihood by cost to express risk in money 14. The trade-offs are covered in Qualitative vs semi-quantitative vs quantitative RBI.
Inspection lowers uncertainty, not damage. API's catalog entry for RP 581 states that an inspection does not itself reduce risk; it reduces uncertainty about the damage present, so the risk can be estimated more accurately 1. That only works if the readings are trusted. OSHA's refinery review tells employers to retest a result that looks wrong instead of setting it aside, and describes cases where wall thickness readings rose over time and no one looked into why 5. How much an inspection tells you depends on its inspection effectiveness.
Which standards and rules apply to RBI?
| Document | Type | What it covers |
|---|---|---|
| API RP 580, Elements of a Risk-Based Inspection Program (4th edition, August 2023; Addendum 1, March 2025) | Recommended practice | Minimum and recommended elements to develop, run and maintain an RBI program; qualitative to fully quantitative approaches 1,2 |
| API RP 581, Risk-Based Inspection Methodology (3rd edition, April 2016, in API's 2025 catalog; for a later edition see What is API 581?) | Recommended practice | Quantitative procedures for vessels, piping, tanks, pressure relief devices and exchanger tube bundles 1 |
| 29 CFR 1910.119(j)(4) | US federal rule | Inspection frequency must follow good engineering practice, and be shorter if operating experience shows the need 4 |
| 49 CFR 195.452 | US federal rule | Hazardous liquid pipelines that could affect high consequence areas: assessment intervals are based on the risk the pipe poses to the area, within a five-year cycle of no more than 68 months 16 |
| Pressure Systems Safety Regulations 2000, regulation 8 | UK law | A written scheme of examination, drawn up or certified by a competent person, sets the nature and frequency of examination 6 |
| HSE L122, Approved Code of Practice for those regulations | UK code of practice | Different parts of a system may be examined at different intervals according to the risk of each part 8 |
In its 2017 review of refinery inspections, the US Occupational Safety and Health Administration (OSHA) named API 510, API 570 and API 580 as examples of recognized engineering practice for piping and vessel inspection 5. Storage tanks are reached through another standard: EPA's guidance for spill prevention inspectors notes that API 653 allows a tank's interval to be set from its corrosion rate or from a risk-based assessment 15. For the two API RBI documents side by side, see API 580 vs API 581: what is the difference?.
What can RBI not do?
- Find a mechanism nobody considered. At Anacortes, Washington, in 2010, CSB ran the RP 581 calculation for high temperature hydrogen attack (HTHA) with the exchanger's design conditions and got a low susceptibility result for equipment that had ruptured, killing seven workers 10. Under the 2nd edition of RP 581, checking the conditions a unit really ran at was optional; the 3rd edition of April 2016 made it a requirement for HTHA, yet CSB closed its recommendation to API on 4 October 2016 as "Closed, Unacceptable Action" because the other parts were not met 11. See What is high temperature hydrogen attack (HTHA)?.
- Make up for readings in the wrong places. At Richmond in 2012, most thickness readings in the line came from fittings high in silicon, which corrode slowly in that service; the low-silicon component that failed had no monitoring point, and a 2002 reading showing it had thinned never reached the tracking database 12.
- Rely on inspection that cannot see the damage. CSB concluded that inspection for HTHA is not reliable enough to depend on 10.
- Move a legal due date on its own. In the UK, the date for the next examination can be postponed only by written agreement with the competent person, only once per examination, only if no danger results, and only with written notice to the enforcing authority before the date 7,8.
- Prove that one method is safer than another. NTSB concluded that nobody knew whether the four risk assessment approaches allowed for US gas pipelines give the same safety benefit, and that state inspectors found risk models among the hardest parts of a program to check 13.
- Cover equipment it was not built for. The 2026 review notes that the API approach is tailored to equipment common in oil and gas, and that hydrogen components such as electrolyzers are not among its listed loss of containment cases 14.
Where integrity problems show up
| Decision | Data it depends on | What goes wrong without it | In the Library |
|---|---|---|---|
| Which components to inspect | Damage mechanism and material for each component, not only each circuit | Philadelphia, 2019: the program assumed uniform corrosion and had no monitoring point on the elbow that thinned to 0.011 inch 9 | What are condition monitoring locations (CMLs)? |
| Which damage mechanisms to model | Actual operating conditions, not only design values | Anacortes, 2010: the HTHA calculation with design conditions gave low susceptibility for exchangers that ruptured 10 | What happened at Anacortes in 2010? |
| Where readings go in a circuit | Material of each component, and every past finding entered in the database | Richmond, 2012: a thinned low-silicon component had no monitoring point and its 2002 reading was not tracked 12 | What happened at Richmond in 2012? |
| How often to inspect | Measured corrosion rates and operating experience | OSHA found unestablished inspection frequencies and corrosion rates not calculated to set thickness intervals 5 | How are inspection intervals set for vessels, piping and tanks? |
| Changing an examination date (UK) | Written scheme of examination and a competent person's agreement | A postponement is lawful only once per examination, without danger, and with notice to the enforcing authority 7 | What should an inspection plan contain? |
Sources: CSB reports 2019-04-I-PA, 2022 9, 2010-08-I-WA, 2014 10, and 2012-03-I-CA, 2015 12; OSHA 3918, 2017 5; PSSR 2000, regulation 9 7.
Common questions
- What is the difference between RBI and time-based inspection?
- Time-based inspection repeats inspections at fixed intervals for a class of equipment. RBI sets interval and method item by item from risk, and UK pressure systems guidance allows different parts of one system to be examined at different intervals for that reason. See [Risk-based inspection vs time-based inspection](/library/rbi-vs-time-based-inspection/).
- Does RBI always lengthen inspection intervals?
- No. Risk can point either way. US process safety rules require more frequent inspection where operating experience shows the need, and the UK code of practice for pressure systems lets the riskier parts of a system be examined more often than the rest.
- Is RBI the same as API 581?
- No. API RP 581 is one quantitative method; API RP 580 allows approaches from qualitative to fully quantitative.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.2025 Publications Catalog (entries for RP 580 and RP 581) (RP 580, 4th edition, August 2023; RP 581, 3rd edition, April 2016, with Addendum 1 (April 2019) and Addendum 2 (October 2020)) · American Petroleum Institute (API)
- 2.Body of Knowledge for API 580 Risk-Based Inspection Certification Exam (2026 exams) (RP 580, 4th edition, August 2023, with Addendum 1 (March 2025)) · American Petroleum Institute (API)
- 3.Glossary: Risk based inspection · Engineering Equipment and Materials Users Association (EEMUA)
- 4.29 CFR 1910.119, Process safety management of highly hazardous chemicals, paragraph (j)(4) · eCFR, US Office of the Federal Register
- 5.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
- 6.The Pressure Systems Safety Regulations 2000 (SI 2000/128), regulation 8 · legislation.gov.uk, The National Archives
- 7.The Pressure Systems Safety Regulations 2000 (SI 2000/128), regulation 9 · legislation.gov.uk, The National Archives
- 8.Safety of pressure systems: Pressure Systems Safety Regulations 2000, Approved Code of Practice and guidance (L122, second edition) · UK Health and Safety Executive (HSE)
- 9.Fire and Explosions at Philadelphia Energy Solutions Refinery Hydrofluoric Acid Alkylation Unit, Investigation Report No. 2019-04-I-PA · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 10.Investigation Report: Catastrophic Rupture of Heat Exchanger (Seven Fatalities), Tesoro Anacortes Refinery, Anacortes, Washington, April 2, 2010, Report No. 2010-08-I-WA · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 11.Recommendations Status Change Summary, Recommendation 2010-8-I-WA-R11 to the American Petroleum Institute (API RP 581) · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 12.Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire, Report No. 2012-03-I-CA · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 13.Integrity Management of Gas Transmission Pipelines in High Consequence Areas, Safety Study NTSB/SS-15/01 · US National Transportation Safety Board (NTSB) ·
- 14.Toward the application of the Risk-Based Maintenance approach to a hydrogen-fueled manufacturing plant (G. Collina and others), International Journal of Hydrogen Energy 238, 155318, open access under CC BY 4.0 · Elsevier, via OSTI.gov (co-authored by the US National Laboratory of the Rockies)
- 15.SPCC Guidance for Regional Inspectors, Chapter 7: Inspection, Evaluation, and Testing · US Environmental Protection Agency (EPA) ·
- 16.49 CFR 195.452, Pipeline integrity management in high consequence areas · eCFR, US Office of the Federal Register