What is positive material identification (PMI)?
Positive material identification (PMI) is testing a metal part, usually with a portable analyzer, to confirm that its alloy matches the specified material. A typical check confirms that a pipe elbow is chromium alloy steel, not carbon steel. PMI is used on receipt, during fabrication and after maintenance; API RP 578 covers verification programs that use it.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
In July 2005, a carbon steel elbow fitted by mistake into a hot, high-pressure hydrogen line at a Texas City, Texas, refinery ruptured after about 3 months, and the fire caused a reported $30 million in damage 1. The three elbows on that exchanger piping had the same dimensions, carbon steel and low-alloy steel cannot be told apart by eye, and the refinery tested alloy parts when they were received and issued for new construction but not when they were removed and refitted during maintenance 1. The US Chemical Safety and Hazard Investigation Board (CSB) found that a quick X-ray fluorescence check would have caught the swap before start-up 1,2. This fire is separate from the explosion at the same refinery in March 2005 1.
How does PMI work?
The CSB describes PMI as identifying and chemically analyzing metal alloys by nondestructive methods 7. ASTM's guide to metals identification groups the methods into quantitative ones, which report how much of each element is present, and qualitative ones, which respond indirectly to chemistry and processing 4.
| Method | How it works | What it does well | Limits |
|---|---|---|---|
| X-ray fluorescence (XRF) | X-rays from a tube or sealed source knock electrons out of inner atomic shells; each element then emits X-rays at its own energies, which the detector sorts 5 | Hand-held and does not damage the part; quickly tells carbon steel from chromium alloy steel 1,7 | Field-portable units do not detect light elements: EPA lists lithium through phosphorus, silicon included, and says elements of atomic number 16 or higher can generally be measured 5; many portable PMI tools cannot read silicon well enough for sulfidation screening 7 |
| Optical emission spectrometry (OES) | A spark excites a small spot of metal and the light given off is measured element by element | Reads light elements; ASTM's laboratory spark method for carbon and low-alloy steel lists 21 elements, including carbon, silicon and phosphorus 6 | Removes a tiny amount of surface metal, which ASTM still counts as nondestructive if the part remains serviceable 4; laboratory versions need a suitable specimen 6 |
| Qualitative sorting | Eddy current, conductivity, thermoelectric, chemical spot, triboelectric and spark tests 4 | Quick sorting of mixed grades 4 | Do not give element percentages 4 |
Carbon has atomic number 6, below every element EPA lists as measurable by field-portable XRF, so carbon content is measured by spark OES or in a laboratory 5,6.
Where is PMI applied?
- Receiving and issue from stores. The Texas City refinery verified alloy components when they arrived at the warehouse and when they were sent out for new construction 1.
- Maintenance. The CSB recommended PMI or another verification method for all critical alloy piping parts removed and reinstalled during maintenance, with parts and locations tagged before removal 1.
- New and existing assets, including welds. API Recommended Practice (RP) 578, Material Verification Program for New and Existing Assets (4th edition, February 2023), covers programs that use PMI and other methods to confirm that an asset, component or weldment matches the specified material 3.
- Existing carbon steel in hot sulfur service. After the 2012 Richmond, California, refinery fire, the CSB recommended that API revise RP 578 to require programs to identify carbon steel circuits that may contain low-silicon components 7.
- Spare parts. US process safety management rules require maintenance materials, spare parts and equipment to be suitable for the process 8. OSHA's 2017 review of its refinery inspections states that positive materials testing must follow the employer's written mechanical integrity procedures and be documented 9.
What can PMI not show?
- Light elements on a portable XRF. Silicon and carbon need OES or laboratory analysis 5,6,7.
- Strength, hardness or heat treatment. ASTM separates spectrometric methods, which respond to alloy content, from electromagnetic and thermoelectric methods, which respond to properties shaped by chemistry and processing 4. PHMSA's 2009 finding of new line pipe up to 15% below its reported yield strength concerned mechanical properties as well as chemistry 10.
- Where a part belongs. A reading tells you what the piece in hand is made of, not which position it came out of. The three Texas City elbows were the same size, and the CSB asked for parts and their locations to be tagged before removal, so records still have to tie each part to its place 1 (see material traceability).
Where integrity problems show up
| Decision or step at this stage | What it affects later | In the Library |
|---|---|---|
| Refitting alloy piping parts after maintenance without PMI | A carbon steel elbow in hot hydrogen service ruptured from high temperature hydrogen attack after fewer than 3,000 hours 1 | What is high temperature hydrogen attack (HTHA)? |
| Not checking silicon in carbon steel for hot sulfur service | Low-silicon components corrode faster; portable PMI often cannot detect silicon, so laboratory analysis or a full thickness survey is needed 7 | What is sulfidation (high-temperature sulfur corrosion)? |
| Specifying steel with at least 9% chromium for sulfidation service | Chromium is easy to verify in the field with portable PMI, and such steels avoid wide corrosion-rate differences within one circuit 7 | How are materials selected for oil and gas equipment? |
| Accepting material on its certificate alone | Certificate values can differ from the product, as PHMSA found in 2009 10 | What is a mill test certificate (EN 10204 3.1 and 3.2)? |
| Controlling spare parts and maintenance materials | US process safety rules require them to suit the process 8 | What is mechanical integrity (MI)? |
Sources: CSB Safety Bulletin 2005-04-B, 2006 1; CSB final report on the 2012 Richmond refinery fire, 2015 7; PHMSA Advisory Bulletin ADB-09-01, 2009 10; 29 CFR 1910.119(j)(6)(iii) 8.
Common questions
- Is PMI the same as positive material verification (PMV)?
- They are closely related. The CSB's 2006 bulletin uses positive material verification for the overall control and PMI for the test, and API calls the overall program a material verification program that uses PMI and other methods.
- Does PMI damage the part?
- XRF does not. Spark OES removes a tiny amount of metal; ASTM's guide counts such methods as nondestructive when the part stays fit for service.
- Does a mill test certificate make PMI unnecessary?
- No. At Texas City the elbows were the right parts in the wrong places, which a certificate cannot reveal, and PHMSA found pipe that did not match its maker's reported values.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Safety Bulletin No. 2005-04-B, BP Texas City, TX Refinery Fire: Positive Material Verification: Prevent Errors During Alloy Steel Systems Maintenance · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 2.CSB Issues Safety Bulletin on BP Texas City Major Fire: Better Material Identification Needed, Errors During Systems Maintenance Cited (news release) · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 3.2025 Publications Catalog (entry for RP 578, Material Verification Program for New and Existing Assets) (RP 578, 4th edition, February 2023) · American Petroleum Institute (API)
- 4.ASTM E1476-04(2022), Standard Guide for Metals Identification, Grade Verification, and Sorting (product page) (E1476-04 (reapproved 2022)) · ASTM International
- 5.SW-846 Test Method 6200: Field Portable X-Ray Fluorescence Spectrometry for the Determination of Elemental Concentrations in Soil and Sediment · US Environmental Protection Agency (EPA)
- 6.ASTM E415-21, Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry (product page) (E415-21) · ASTM International
- 7.Final Investigation Report: Chevron Richmond Refinery Pipe Rupture and Fire · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 8.29 CFR 1910.119, Process safety management of highly hazardous chemicals · eCFR, US Office of the Federal Register
- 9.Process Safety Management for Petroleum Refineries: Lessons Learned from the Petroleum Refinery Process Safety Management National Emphasis Program (OSHA 3918) · US Occupational Safety and Health Administration (OSHA)
- 10.Pipeline Safety: Potential Low and Variable Yield and Tensile Strength and Chemical Composition Properties in High Strength Line Pipe (Advisory Bulletin ADB-09-01), 74 FR 23930 · US Pipeline and Hazardous Materials Safety Administration (PHMSA), via Federal Register (govinfo) ·