What is a safety integrity level (SIL)?
A safety integrity level (SIL) is one of four discrete levels, SIL 1 to SIL 4, that state how reliably a safety instrumented function must act on demand. SIL 4 is the most demanding. IEC 61508 defines the levels for safety-related systems, and IEC 61511 applies them to safety instrumented systems in the process industry.
By Jun Zhong, Editor·Researched and drafted by Beacon's AI newsroom·Checked by Jun Zhong, Editor·Last checked ·Next review
Why does it matter?
When the UK Health and Safety Executive (HSE) analyzed 34 incidents involving control systems for its guidance Out of control, it traced 44% of them primarily to the specification phase, before design began, and 20% to changes made after commissioning 1. HSE cautions that the sample is small, but concludes that most of these failures could have been foreseen with a systematic, risk-based approach over the whole life of the system 1. In HSE's scheme the specification phase includes the safety integrity requirements, which is where the required SIL is recorded 1. Every later step, from design to proof testing, is then judged against that level 2.
What does a SIL specify?
A SIL belongs to a safety function, not to a plant or a single instrument. The US Chemical Safety and Hazard Investigation Board (CSB) report on the 2018 Superior, Wisconsin, refinery explosion quotes the Center for Chemical Process Safety (CCPS) glossary: a SIL is one of four discrete levels allocated to a safety instrumented function (SIF), the combination of sensors, logic solver and final control elements that takes the process to a safe state 3. HSE describes safety integrity as the probability that a safety-related system performs its function under all stated conditions, within a stated time, when it is called on, and links it to both performance and availability 2.
IEC 61508 links the four levels to required measures of risk reduction and treats functions demanded only occasionally (low demand mode) separately from those that act continuously 2. This page does not reproduce the numeric targets. HSE's summary of the standard covers three kinds of requirement for claiming a level 2:
| Requirement | What it covers |
|---|---|
| Random hardware failures | A reliability model of the function's architecture, with predicted failure performance compared with the target level 2 |
| Architectural constraints | Minimum fault tolerance (redundancy) and diagnostic coverage for each element or subsystem 2 |
| Systematic failures | A managed safety lifecycle that runs from hazard and risk evaluation and specification through design, installation and commissioning, validation, operation and maintenance, to later modification 2 |
IEC 61508-1 is in its second edition (2010), and the IEC webstore listed a third edition as under development on 25 October 2026 6. IEC 61511-1, the process-sector application, is edition 2.0 (2016) with Amendment 1 (2017) 7.
How is the required SIL decided?
HSE describes the sequence: identify each hazard and what can start it, estimate how likely it is, evaluate the overall risk, and work out how much risk reduction is needed to reach a tolerable level 2. The safety functions that deliver that reduction are then allocated to instrumented systems, other technology or external measures, and each instrumented function gets the level its share of the reduction requires 2.
- Semi-quantitative methods. Layer of protection analysis (LOPA) credits the independent layers already present and sizes the gap a SIF must close; the 2016 LOPA at the Superior refinery was run partly to set SIF requirements 3.
- Qualitative methods. HSE notes that the level can instead be chosen from the likelihood and consequence of the hazard, the frequency and duration of exposure, and whether the hazard can be avoided 2.
- Scenario sources. The scenarios come from the process hazard analysis; HSE recommends formal techniques such as a hazard and operability study (HAZOP) where failure could cause significant harm 1,3.
How is a SIL kept in operation?
- Proof testing. Where diagnostic coverage is low, HSE notes that the integrity achieved depends critically on how often proof tests are run and whether they reveal failures that stay hidden in normal operation 2. It describes tests at trip conditions, end-to-end tests that also prove impulse lines, and written pass and fail criteria 2.
- Repair and overrides. Where diagnostics are extensive, the result depends on how quickly revealed faults are repaired, and overrides need authorization, recording and review 2.
- Latent failures. In its 2014 report on the 2010 Macondo blowout in the Gulf of Mexico, the CSB found that weekly function testing of the blowout preventer did not reveal latent faults in its emergency system: one of two redundant control pods had miswiring and a drained battery, and a key valve in the other was also miswired 4.
- Mechanical integrity. The US process safety management (PSM) rule places emergency shutdown systems and controls, including sensors, alarms and interlocks, in the mechanical integrity program, with inspections and tests that follow recognized and generally accepted good engineering practices 5.
Where integrity problems show up
| Element or step | Integrity link | In the Library |
|---|---|---|
| Safety requirements specification | 44% of the incidents HSE analyzed began here, through poor hazard analysis or unassessed failure modes 1 | What is layer of protection analysis (LOPA)? |
| Final element, such as an emergency shutdown valve | HSE's offshore asset integrity program found performance standards that were generic, without measurable criteria such as maximum valve closure time or allowable leak rate 8 | Performance standard (for safety-critical elements) |
| Proof test of the whole function | Hidden failures stay hidden until a test reveals them; routine function tests missed the latent faults at Macondo 2,4 | What is a safety instrumented system (SIS)? |
| Sensors and process connections | HSE lists protection against vibration and corrosion of the process connection, and control of isolation valves between tests 2 | What are safety and environmental critical elements (SECEs)? |
| Test records | The PSM rule requires each inspection and test to be documented with date, performer, equipment identifier, description and results 5 | What is mechanical integrity (MI)? |
| Changes after commissioning | 20% of the incidents HSE analyzed began with modifications made after commissioning 1 | What is management of change (MOC)? |
Sources: HSE HSG238, 2003 1; HSE COMAH technical measures, control systems 2; CSB Macondo report, Volume 2, 2014 4; 29 CFR 1910.119(j) 5; HSE KP3 report, 2007 8.
Common questions
- What is the difference between SIL, SIS and SIF?
- A safety instrumented system (SIS) is the whole set of sensors, logic solvers and final elements; a safety instrumented function (SIF) is one protective action that the system performs; and the SIL is the integrity level assigned to that function.
- Does a "SIL-certified" device make a function SIL-rated?
- No. HSE notes that SILs quoted for certified subsystems should come with their proof test interval, diagnostic coverage and fault tolerance, and help with architecture, but the level of the complete function still has to be confirmed.
- Does US regulation require a SIL?
- The PSM rule does not use the term. It requires emergency shutdown systems, interlocks and other controls to be inspected and tested under recognized and generally accepted good engineering practices, with documented results.
Beacon explains these concepts in its own words for education. It does not reproduce or replace the standards cited, and Winda is not affiliated with or endorsed by the organizations that publish them. Engineering decisions need the current edition of the standard and a qualified engineer.
Sources
- 1.Out of control: Why control systems go wrong and how to prevent failure (HSG238), second edition · UK Health and Safety Executive (HSE)
- 2.Control systems (COMAH technical measures document) · UK Health and Safety Executive (HSE)
- 3.Investigation Report: FCC Unit Explosion and Asphalt Fire at Husky Superior Refinery, Superior, WI (Report No. 2018-02-I-WI) · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 4.Investigation Report Volume 2: Explosion and Fire at the Macondo Well (Report No. 2010-10-I-OS) · US Chemical Safety and Hazard Investigation Board (CSB) ·
- 5.29 CFR 1910.119, Process safety management of highly hazardous chemicals (paragraph (j)) · eCFR, US Office of the Federal Register
- 6.IEC 61508-1:2010, Functional safety of electrical/electronic/programmable electronic safety-related systems, Part 1: General requirements (product page) (Edition 2.0 (2010); edition 3.0 listed as under development on 2026-10-25) · International Electrotechnical Commission (IEC) ·
- 7.IEC 61511-1:2016, Functional safety: Safety instrumented systems for the process industry sector, Part 1 (product page) (Edition 2.0 (2016); Amendment 1 (2017), consolidated as edition 2.1) · International Electrotechnical Commission (IEC) ·
- 8.Key Programme 3: Asset Integrity Programme · UK Health and Safety Executive (HSE), Offshore Division